Command access PD15-UL-M Instructions Manual

PD15-UL-M KIT

INSTRUCTIONS

The Command Access PD15-UL-M-KIT is a eld-installable motorized latch-

pullback kit for the Jackson 1285/95 & AHT 8/9 series devices.

A.

B. C.

E.

KIT INCLUDES | TOOLS REQUIRED

60241 Motor Mount

A.

1-

60264 MM4 RM series module (w/ optional REX)

B.

1-

40040 Phillips Screws

C.

2-

50453 Bracket

D.

1-

40059 Cable Mounting Pad

E.

2-

50636 Cable Guides

F.

3-

40060 Cable Ties

G.

2-

50741 MM4 RM Cable

1-

H.

50436 8’ Lead

1-

I.

F.D.

G. H. I.

Cordless Drill

1/16” drill bit

File

#2 Phillips head screwdriver

PH-00 Screwdriver

Watch the Video

US customer support 1-888-622-2377 | www.commandaccess.com | CA customer support 1-855-823-3002

#20379_J

MM4 Switches

off

1

on

on

2

off

Technical Information

STANDARD TORQUE

HIGH TORQUE

PTS PROGRAMMING ON

PTS PROGRAMMING LOCKED

Make sure to set PTS before nishing installation

SPECIFICATIONS

• Input Voltage: 24VDC +/- 10%

• Wire gauge: Minimum 18 gauge

• Direct wire run - no relays or
access control units in-between
power supply & module

Setting PTS

**Important Info**

Standard Torque Mode

Average Latch Retraction Current: 1 Amp
Average Holding Current: 215 mA

High Torque Mode

Average Latch Retraction Current: 2 Amp
Average Holding Current: 250 mA

Step 1

Step 2

Step 3

Step 4

• Select your preferred torque mode (ships in standard torque) Press the device push pad to the
desired setting. (Recommend to fully depress and release 5%, giving the device room for changing
door conditions.)

• While depressing the push pad, apply power. (i.e. presenting the credential to the reader).

• Continue to keep pad depressed, the device will beep 6 times. After the beeps have stopped, release the
pad and now the adjustment is complete. If not to your liking repeat the 3 steps.

• Once you’ve found the correct location, ip the dip switch to o to lock programming.

Troubleshooting & Diagnostics

Beeps

2 Beeps

3 Beeps

4 Beeps Failed Sensor Verify all 3 sensor wires are installed correctly. Replace sensor if

5 Beeps

6 Beeps

Explanation

Over Voltage

Under Voltage

Retraction or dogging failure

PUSH TO SET

Solution

> 30V unit will shut down. Check voltage & adjust to 24 V.

< 20V unit will shut down. Check voltage & adjust to 24 V.

problem persists by contacting oce.

After 1st fail: 5 beeps then immediately attempts to retract again.
After 2nd fail: 5 beeps with pause in-between for 30 seconds then
device attempts to retract again.
After 3rd fail: 5 beeps every 7 minutes, device will not attempt to
retract.
To Reset: Depress bar for 5 seconds at any time.

Device is recording it’s new position and power mode after the 6th beep.

US customer support 1-888-622-2377 | www.commandaccess.com | CA customer support 1-855-823-3002

Ceiling Tile

Electried Exit Device

INSTALLATION EXAMPLE

CAT

DRY CONTACT FROM

ACCESS CONTROL

NORMALLY OPEN

SYSTEM

NO VOLTAGE

GREEN

CHANNEL 1

LED

­+

LOCKING
HARDWARE

Module

Legend

Standard Placement

Recommended PoweR SuPPlieS:

All Command Access exit devices & field installable kits have been thoroughly cycle

tested with Command Access power supplies at our factory.

For more information click here or go to our website

US customer support 1-888-622-2377 | www.commandaccess.com | CA customer support 1-855-823-3002

STEP 1 - Disassemble Exit Device

Remove (2) screws on push pad end caps from

1.

front & back

1

2

Once connecting rods are disconnected from front

3.

activating bracket ip device over.

Pull back push pad exposing the front activating brack-

2.

et. Remove guides and roll pin from activating bracket.

Remove head assembly by removing (2) screws.

4.

1

Slide push pad forward to remove from device.

5. 6.

US customer support 1-888-622-2377 | www.commandaccess.com | CA customer support 1-855-823-3002

Underneath pushpad remove dogging assembly.

2

Re-attach head assembly by securing (2) screws.

7.

Next, we’ll be installing the kit in between the

8.

activating brackets on the exposed baserail.

CVR

RIM

2

1

1

STEP 2- Installing Kit

Add bracket #50453 to front activating bracket. Dropping it over the top and securing it with the

9.

screw provided.

**Important Info**

BEFORE MOVING TO STEP 2 - SEE STEP C on PAGE 8

BEFORE

PILOT HOLE

PILOT HOLE IN INCHES (“)

1/2”

1/4”

AMOUNT REMOVED IN INCHES (“)

AFTER

5/8”

5/16”

10.

On the baserail, remove the back (2)
screws from the dogging bracket.

2

Make sure scissor bracket on bottom side is diagonal

11.

& screws are ush before installing.

1

FRONT

US customer support 1-888-622-2377 | www.commandaccess.com | CA customer support 1-855-823-3002

1

2

Next, drop the motor mount in with the front over the front activating bracket.

12.

Line up the back with the (2) available screw holes and the bracket securing the motor mount.

13.

2

1

Push screws to correct position (pictured) to straighten

14.

scissor bracket and secure front end of the motor kit by
tightening (2) screws.

Slide MM4 module into housing’s channel on the

17. 18.

back of the device.

16.

Slide all the way up until the MM4 bracket is
almost ush with end of the channel. Tighten all
(4) screws here to secure MM4

Tighten back end of the module by re­installing (2) screws from dogging bracket.

Push Pad

End of Channel

1

3

2

US customer support 1-888-622-2377 | www.commandaccess.com | CA customer support 1-855-823-3002

4

Connect MM4 Cable. Attach the strain relief and secure MM4 cable with a zip tie.

19.

20.

1. Attach the wire guides to the inside of the baserail.

2. Route wires along the inside of the baserail using the wire guides.

**HOOK UP TO POWER & TEST MOTOR BEFORE MOVING ON TO STEP 5.**

STEP 3 - Reassemble Exit Device

Re-install pins and connecting rods on both

1.

activating brackets

Rod

Once guides & bumpers are installed on activating

2.

brackets slide on the push pad.

Connecting Rod

Back of device

Front

Turn over BACK push pad end cap over and start a pilot hole beneath the bottom right hand corner

3.

(see measurements below). Use the gold bracket as a guide. Once your hole is drilled use your

preferred method to clear out the remaining debris and le to clean up the edges.

BEFORE

PILOT HOLE IN INCHES (“)

1/4”

1. Slide BACK push pad end cap into channel before re-installing to push pad.

4.

2. Re-install (2) screws on BACK & FRONT push pad end caps.

PILOT HOLE

AMOUNT REMOVED IN INCHES (“)

1/2”

AFTER

5/8”

5/16”

1

2

1. Slide ller plates on and plug into power.

5.

2. Set “Push-to-Set” and once you found the correct location, turn PTS switch to OFF position.

Setting PTS

Step 1-

Step 2-

Step 3-

Step 4-

US customer support 1-888-622-2377 | www.commandaccess.com | CA customer support 1-855-823-3002

Select your preferred torque mode (ships in standard torque) Press the device push pad to the
desired setting. (Recommend to fully depress and release 5%, giving the device room for
changing door conditions.)

While depressing the push pad, apply power. (i.e. presenting the credential to the reader).

Continue to keep pad depressed, the device will beep 6 times. After the beeps have
stopped, release the pad and now the adjustment is complete. If not to your liking repeat

the three steps.
Once you found the correct location, ip the dip switches to o to lock programming.

MM4 Switches

off

1

on

on

2

off

STANDARD TORQUE

HIGH TORQUE

PTS PROGRAMMING ON

PTS PROGRAMMING LOCKED