Comfort Glow SL30NT Owner's Operation And Installation Manual

Page 1
(VENT-FREE) NATURAL GAS STOVE HEATER
OWNER’S OPERATION AND INSTALLATION MANUAL
For more information, visit www.desatech.com
For more information, visit www.desatech.com
SL30NT
Patent Pending
Model SL30NT Series Thermostat Control Gas Log Heater
(Burner System For Cast Iron Stoves)
WARNING: If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal in­jury, or loss of life.
— Do not store or use gasoline or other
flammable vapors and liquids in the vicinity of this or any other appliance.
— WHAT TO DO IF YOU SMELL GAS
Do not touch any electrical switch; do not use any phone in your building.
Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
If you cannot reach your gas supplier, call the fire department.
— Installation and service must be per-
formed by a qualified installer, service agency, or the gas supplier.
This appliance may be installed in an aftermarket*, permanently located, manufactured (mobile) home, where not prohibited by local codes.
This appliance is only for use with the type of gas indicated on the rating plate. This appli­ance is not convertible for use with other gases.
WARNING: The SL30NT series vent-free gas log heater is only approved for use in the Comfort Glow series cast iron stove models CISC and CISG.
WARNING: Improper installation, adjustment, alteration, service, or maintenance can cause injury or property damage. Refer to this manual for correct installation and opera­tional procedures. For assistance or addi­tional information consult a qualified installer, service agency, or the gas supplier.
WARNING: This is an unvented gas-fired heater. It uses air (oxygen) from the room in which it is installed. Provisions for adequate combustion and ventilation air must be pro­vided. Refer to
tilation
section on page 4 of this manual.
Air for Combustion and Ven-
* Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer
Save this manual for future reference.
Save this manual for future reference.
Page 2
TABLE OF CONTENTS
2
SAFETY INFORMATION
TABLE OF CONTENTS
SAFETY INFORMATION ............................................................ 2
PRODUCT IDENTIFICATION ..................................................... 3
LOCAL CODES........................................................................... 3
PRODUCT FEATURES .............................................................. 4
AIR FOR COMBUSTION AND.................................................... 4
VENTILATION ............................................................................. 4
INSTALLATION ........................................................................... 6
OPERATING HEATER.............................................................. 13
INSPECTING BURNERS.......................................................... 14
CLEANING AND MAINTENANCE ............................................ 14
SAFETY INFORMATION
WARNINGS
WARNING ICON G 001
WARNING: This product contains and/or generates chemicals known to the State of California to cause cancer or birth defects, or other reproductive harm.
IMPORTANT: Read this owners manual carefully and completely before trying to assemble, operate, or ser­vice this heater. Improper use of this heater can cause serious injury or death from burns, fire, explosion, electrical shock, and carbon monoxide poisoning.
DANGER: Carbon monoxide poisoning may lead to death!
SPECIFICATIONS .................................................................... 15
TROUBLESHOOTING .............................................................. 16
SERVICE HINTS....................................................................... 19
TECHNICAL SERVICE ............................................................. 19
REPLACEMENT PARTS .......................................................... 19
ACCESSORIES ........................................................................ 19
ILLUSTRATED PARTS BREAKDOWN AND PARTS LIST ....... 20
PARTS CENTRALS .................................................................. 24
OWNER’S REGISTRATION FORM.......................................... 25
WARRANTY INFORMATION...................................... Back Cover
WARNING: Do not allow fans to blow directly into the stove. Avoid any drafts that alter burner flame patterns. Ceiling fans can create drafts that alter burner flame patterns. Altered burner patterns can cause sooting.
WARNING: Do not use a blower insert, heat exchanger insert or other accessory not approved for use with this heater.
Due to high temperatures, the appliance should be located out of traffic and away from furniture and draperies.
Carbon Monoxide Poisoning: Early signs of carbon monoxide
poisoning resemble the flu, with headaches, dizziness, or nausea. If you have these signs, the heater may not be working properly. Get fresh air at once! Have heater serviced. Some people are more affected by carbon monoxide than others. These include pregnant women, people with heart or lung disease or anemia, those under the influence of alcohol, and those at high altitudes.
Natural Gas: Natural gas is odorless. An odor-making agent is
added to the gas. The odor helps you detect a gas leak. However, the odor added to the gas can fade. Gas may be present even though no odor exists.
Make certain you read and understand all warnings. Keep this manual for reference. It is your guide to safe and proper operation of this heater.
WARNING: Any change to this heater or its
controls can be dangerous.
For more information, visit www.desatech.com
For more information, visit www.desatech.com
Do not place clothing or other flammable material on or near the appliance. Never place any objects on the heater.
Stove becomes very hot when running heater. Keep children and adults away from hot surface to avoid burns or clothing ignition. Heater will remain hot for a time after shutdown. Allow surface to cool before touching.
Carefully supervise young children when they are in the room with fireplace.
Keep the appliance area clear and free from combus­tible materials, gasoline, and other flammable vapors and liquids.
104463-01E
Page 3
SAFETY INFORMATION
Continued
SAFETY INFORMATION
PRODUCT IDENTIFICATION
LOCAL CODES
3
3
1. This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases.
2. If you smell gas
• shut off gas supply
• do not try to light any appliance
• do not touch any electrical switch; do not use any phone in
your building
• immediately call your gas supplier from a neighbor’ s phone.
Follow the gas supplier’s instructions
• if you cannot reach your gas supplier , call the fire department
3. This heater shall not be installed in a bedroom or bathroom.
4. Do not place stove directly on carpeting, vinyl tile, or any combustible material other than wood. The stove must set on a metal or wood panel extending the full width and depth of the appliance.
5. Do not use this stove as a wood burning fireplace. Use only model SL30NT series vent-free gas log heater.
6. Do not add extra logs or ornaments such as pine cones, vermicu­lite, or rock wool. Using these added items can cause sooting.
7. This log heater is designed to be smokeless. If logs ever appear to smoke, turn off heater and call a qualified service person.
Note:
During initial operation, slight smoking could occur due
to log curing and heater burning manufacturing residues.
8. To prevent the creation of soot, follow the instructions in Clean- ing and Maintenance, pages 14 and 15.
9. Before using furniture polish, wax, carpet cleaners, or similar products, turn heater off. If heated, the vapors from these prod­ucts may create a white powder residue within burner box or on adjacent walls or furniture.
10. This heater needs fresh, outside air ventilation to run properly. This heater has an Oxygen Depletion Sensing (ODS) safety shutoff system. The ODS shuts down the heater if not enough fresh air is available. See Air for Combustion and Ventilation, pages 4 through 6. If heater keeps shutting off, see Trouble- shooting, pages 16 through 18.
11. Do not run heater
• where flammable liquids or vapors are used or stored
• under dusty conditions
12. Do not use this stove to cook food or burn paper or other objects.
13. Do not use heater if any part has been exposed to or under water. Immediately call a qualified service technician to in­spect the room heater and to replace any part of the control system and any gas control which has been under water.
14. Do not operate heater if any log is broken. Do not operate heater if a log is chipped (dime-sized or larger).
15. Turn heater off and let cool before servicing. Only a qualified service person should service and repair heater.
16. Operating heater above elevations of 4,500 feet could cause pilot outage.
17. Provide adequate clearances around air openings.
PRODUCT IDENTIFICATION
Stove Body
One Piece Log Set Inside Stove Cavity
Piezo
Stove Door
Ignitor
(Shown in the open position)
Figure 1 - Typical Stove Cabinet Model with Comfort Glow Gas Log Heater
Control Knob
LOCAL CODES
Install and use heater with care. Follow all local codes. In the absence of local codes, use the latest edition of The National Fuel Gas Code ANSI Z223.1/NFPA 54*.
*Available from:
American National Standards Institute, Inc.
1430 Broadway
New York, NY 10018
National Fire Protection Association, Inc.
Batterymarch Park
Quincy, MA 02269
For more information, visit www.desatech.com
For more information, visit www.desatech.com
104463-01E
Page 4
PRODUCT FEATURES AIR FOR COMBUSTION AND VENTILATION
4
Providing Adequate Ventilation
PRODUCT FEATURES
OPERATION
This heater is clean burning. It requires no outside venting. There is no heat loss out a vent or up a chimney. Heat is generated by realistic, dancing yellow flames. This heater is designed for vent-free operation. State and local codes in some areas prohibit the use of vent-free heaters.
SAFETY PILOT
This heater has a pilot with an Oxygen Depletion Sensing (ODS) safety shutoff system. The ODS/pilot is a required feature for vent­free room heaters. The ODS/pilot shuts off the heater if there is not enough fresh air.
PIEZO IGNITION SYSTEM
This heater has a piezo ignitor. This system requires no matches, batteries, or other sources to light heater.
AIR FOR COMBUSTION AND VENTILATION
WARNING: This heater shall not be installed in a confined space or unusually tight construction unless provisions are provided for adequate com­bustion and ventilation air. Read the following in­structions to insure proper fresh air for this and other fuel-burning appliances in your home.
Today’s homes are built more energy efficient than ever. New mate­rials, increased insulation, and new construction methods help reduce heat loss in homes. Home owners weather strip and caulk around windows and doors to keep the cold air out and the warm air in. During heating months, home owners want their homes as airtight as possible.
While it is good to make your home energy efficient, your home needs to breathe. Fresh air must enter your home. All fuel-burning appliances need fresh air for proper combustion and ventilation.
Exhaust fans, fireplaces, clothes dryers, and fuel burning appliances draw air from the house to operate. You must provide adequate fresh air for these appliances. This will insure proper venting of vented fuel-burning appliances.
Unusually Tight Construction
The air that leaks around doors and windows may provide enough fresh air for combustion and ventilation. However, in buildings of unusually tight construction, you must provide additional fresh air.
Unusually tight construction is defined as construction where:
a. walls and ceilings e xposed to the outside atmosphere
have a continuous water vapor retarder with a rating of one perm (6 x 10 openings gasketed or sealed
b. weather stripping has been added on openable win-
dows and doors
c. caulking or sealants are applied to areas such as
joints around window and door frames, between sole plates and floors, between wall-ceiling joints, between wall panels, at penetrations for plumbing, electrical, and gas lines, and at other openings.
If your home meets all of the three criteria above, you must provide additional fresh air. See
From Outdoors
If your home does not meet all of the three criteria above, proceed to
tion,
page 5.
, page 6.
Determining Fresh-Air Flow For Heater Loca-
-11
kg per pa-sec-m2) or less with
and
and
Ventilation Air
Confined and Unconfined Space
The National Fuel Gas Code ANSI Z223.1/NFPA 54 defines a confined space as a space whose volume is less than 50 cubic feet per 1,000 Btu per hour (4.8 m3 per kw) of the aggregate input rating of all appliances installed in that space and an unconfined space as a space whose volume is not less than 50 cubic feet per 1,000 Btu per hour (4.8 m3 per kw) of the aggregate input rating of all appliances installed in that space. Rooms communicating directly with the space in which the appliances are installed*, through openings not furnished with doors, are considered a part of the unconfined space.
* Adjoining rooms are communicating only if there are doorless passageways or ventilation grills between them.
PROVIDING ADEQUATE VENTILATION
The following are excerpts from National Fuel Gas Code, ANSI Z223.1/NFPA 54, Section 5.3, Air for Combustion and Ventilation.
All spaces in homes fall into one of the three following ventilation classifications:
1. Unusually Tight Construction
2. Unconfined Space
3. Confined Space The information on pages 4 through 6 will help you classify your
space and provide adequate ventilation.
For more information, visit www.desatech.com
For more information, visit www.desatech.com
104463-01E
Page 5
AIR FOR COMBUSTION AND VENTILATION
Continued
AIR FOR COMBUSTION AND VENTILATION
Determining Fresh-Air Flow for Heater Location
5
5
DETERMINING FRESH-AIR FLOW FOR HEATER LOCATION
Determining if You Have a Confined or Unconfined Space
Use this work sheet to determine if you have a confined or uncon­fined space.
Space: Includes the room in which you will install heater plus any adjoining rooms with doorless passageways or ventilation grills between the rooms.
1. Determine the volume of the space (length x width x height). Length x Width x Height = _________ cu. ft. (volume of space)
Example:
(ceiling height) = 2560 cu. ft. (volume of space) If additional ventilation to adjoining room is supplied with grills
or openings, add the volume of these rooms to the total vol­ume of the space.
2. Multiply the space volume by 20 to determine the maximum Btu/Hr the space can support.
_________________ (volume of space) x 20 = (maximum
Btu/Hr the space can support)
Example:
mum Btu/Hr the space can support)
3. Add the Btu/Hr of all fuel burning appliances in the space.
* Do not include direct-vent gas appliances. Direct-vent draws combustion air from the outdoors and vents to the outdoors.
Space size 20 ft. (length) x 16 ft. (width) x 8 ft.
2560 cu. ft. (volume of space) x 20 = 51,200 (maxi-
Vent-free heater _______________Btu/Hr Gas water heater* _______________Btu/Hr Gas furnace _______________Btu/Hr Vented gas heater _______________Btu/Hr Gas fireplace logs _______________Btu/Hr Other gas appliances* + ______________Btu/Hr Total = ______________Btu/Hr
Example:
Gas water heater 40,000 Btu/Hr Vent-free heater + 30,000 Btu/Hr Total = 70,000 Btu/Hr
4. Compare the maximum Btu/Hr the space can support with the actual amount of Btu/Hr used.
_____________ Btu/Hr (maximum the space can support) _____________ Btu/Hr (actual amount of Btu/Hr used)
Example:
The space in the above example is a confined space because the actual Btu/Hr used is more than the maximum Btu/Hr the space can support. You must provide additional fresh air. Your options are as follows:
A. Rework worksheet, adding the space of an adjoining room. If
the extra space provides an unconfined space, remove door to adjoining room or add ventilation grills between rooms. See Ventilation Air From Inside Building, page 6.
B. Vent room directly to the outdoors. See Ventilation Air From
Outdoors, page 6.
C. Install a lower Btu/Hr heater, if lower Btu/Hr size makes room
unconfined.
If the actual Btu/Hr used is less than the maximum Btu/Hr the space can support, the space is an unconfined space. You will need no additional fresh air ventilation.
WARNING: If the area in which the heater may be operated is smaller than that defined as an uncon­fined space or if the building is of unusually tight construction, provide adequate combustion and ven­tilation air by one of the methods described in the
National Fuel Gas Code, ANSI Z223.1/NFPA 54, Sec­tion 5.3
51,200 Btu/Hr (maximum the space can support) 70,000 Btu/Hr (actual amount of Btu/Hr used)
or applicable local codes.
For more information, visit www.desatech.com
For more information, visit www.desatech.com
104463-01E
Page 6
AIR FOR COMBUSTION AND VENTILATION
6
Ventilation Air
INSTALLATION
AIR FOR COMBUSTION AND VENTILATION
Continued
VENTILATION AIR Ventilation Air From Inside Building
This fresh air would come from an adjoining unconfined space. When ventilating to an adjoining unconfined space, you must provide two permanent openings: one within 12" of the ceiling and one within 12" of the floor on the wall connecting the two spaces (see options 1 and 2, Figure 2). You can also remove door into adjoining room (see option 3, Figure 2). Follow the National Fuel
Gas Code, ANSI Z223.1/NFPA 54, Section 5.3, Air for Combustion and Ventilation for required size of ventilation grills or ducts.
Ventilation Air From Outdoors
Provide extra fresh air by using ventilation grills or ducts. You must provide two permanent openings: one within 12" of the ceiling and one within 12" of the floor. Connect these items directly to the outdoors or spaces open to the outdoors. These spaces include attics and crawl spaces. Follow the National Fuel Gas Code, ANSI
Z223.1/NFPA 54, Section 5.3, Air for Combustion and Ventilation
for required size of ventilation grills or ducts.
IMPORTANT:
into attic if attic has a thermostat-controlled power vent. Heated air entering the attic will activate the power vent.
Ventilation
Grills
Into Adjoining
Room,
Option 1
Do not provide openings for inlet or outlet air
12"
Ventilation Grills
Or
Remove
Door into
Adjoining
Room, Option
3
Into Adjoining Room,
Option 2
Outlet Air
Outlet Air
Inlet Air
Inlet Air
Figure 3 - Ventilation Air from Outdoors
Ventilated Attic
To Attic
To
Crawl
Space
Ventilated
Crawl Space
INSTALLATION
NOTICE: This heater is intended for use as supple­mental heat. Use this heater along with your primary heating system. Do not install this heater as your primary heat source. If you have a central heating system, you may run systems circulating blower while using heater. This will help circulate the heat throughout the house. In the event of a power outage, you can use this heater as your primary heat source.
WARNING: A qualified service person must in­stall heater. Follow all local codes.
NOTICE: State or local codes may only allow opera­tion of this appliance in a vented configuration. Check your state or local codes.
12"
Figure 2 - Ventilation Air from Inside Building
For more information, visit www.desatech.com
For more information, visit www.desatech.com
WARNING: Never install the heater
in a bedroom or bathroom
in a recreational vehicle
where curtains, furniture, clothing, or other flam-
mable objects are less than 42 inches from the front, top, or sides of the heater
in high traffic areas
in windy or drafty areas
104463-01E
Page 7
INSTALLATION
12"
Minimum
12"
Minimum
48"
Minimum
Ceiling
Side Wall Side Wall
Back Wall
Side Wall Side Wall
12
"
Minimum
12
"
Minimum
6
"
Minimum
Continued
CAUTION: This heater creates warm air currents. These currents move heat to wall surfaces next to heater. Installing heater next to vinyl or cloth wall coverings or operating heater where impurities (such as, but not limited to, tobacco smoke, aromatic candles, cleaning fluids, oil or kerosene lamps, etc.) in the air exist, may discolor walls or cause odors.
INSTALLATION
Check Gas Type
Clearances to Combustibles
Front View
7
7
IMPORTANT:
Vent-free heaters add moisture to the air. Although this is beneficial, installing heater in rooms without enough venti­lation air may cause mildew to form from too much moisture. See Air for Combustion and Ventilation, pages 4 through 6.
CHECK GAS TYPE
Use only natural gas. If your gas supply is not natural gas, do not install heater. Call dealer where you bought heater for proper type heater.
CLEARANCES TO COMBUSTIBLES (Vent-Free Operation Only)
WARNING: Maintain the minimum clearances. If you can, provide greater clearances from floor, ceil­ing, and adjoining side and back walls.
Carefully follow the instructions below. This stove is a freestanding unit designed to set directly on the floor.
IMPORTANT:
You must maintain minimum wall and ceiling clearances during installation. The minimum clearances are shown in Figure 4. Measure from outermost point of stove top.
Minimum Wall and Ceiling Clearances (see Figure 4)
A. Clearances from outermost point of stove top to any combus-
tible side wall should not be less than 12 inches.
B. Clearances from outermost point of stove top to any combus-
tible back wall should not be less than 6 inches (Includes Cor­ner Installations).
C. Clearances from the stove top to the ceiling should not be less
than 48 inches.
Corner
Wall
6
"
Minimum
Ceiling
48"
Minimum
Front of
Stove Unit
Wall
Minimum
6"
Minimum
6
"
Front of
Stove Unit
Back Wall
Top View
Side View
104463-01E
For more information, visit www.desatech.com
For more information, visit www.desatech.com
Front of
Stove Unit
Floor
Figure 4 - Minimum Clearance to Walls and Ceiling (Stove May Vary Depending on Model)
Page 8
INSTALLATION
INSTALLATION
Stove Cavity Assembly
8
Stove Cavity Assembly
INSTALLATION
Continued
STOVE CAVITY ASSEMBLY
1. Lift off corrugated box enclosing stove body crating.
2. Remove all screws fastening the wood frame enclosure.
Spread wood frame open and lift away from plastic-bagged stove body. The bottom pieces of pallet wood will remain bolted to the stove body.
3. Remove plastic bag from stove body.
4. Remove back panel from stove (see Figure 5). Use an adjust-
able wrench or a 10 mm socket. Remove six (6) bolts and wash­ers. Keep bolts and washers to reattach back panel later.
5. Remove all contents from inside stove cavity. Contents include:
(1) - Stove bottom (4) - Legs (1) - Bottom door (1) - Top grate (1) - Hardware kit bag with fasteners
6. Carefully lay stove body on back to attach bottom components
to stove body (see Figure 6). Rest stove on drop cloth or blan­ket to avoid scratching stove edges.
Back Stove Panel
Bolt
Product Identification Label
7. Remove remaining pallet wood attached to bottom of stove body (see Figure 7). Use an adjustable wrench to remove bolts.
8. Fasten each leg to stove with four (4) bolts. Use a flat screw driver to tighten bolt to leg. Thread bolt in tapped holes on stove body (see Figure 8 and Figure 9, page 9).
Front
Bolt
Pallet Wood
Figure 7 - Removing Pallet Wood From The Bottom of The Stove
Door Hinge Step Bolt Hole
Leg Hole
Leg Hole
Figure 8 - Locating Threaded Holes for Stove Bottom, Legs, and Door Attachment (Appearance May Vary Depending on Model)
Front
Stove Bottom Holes
Pallet Wood
Bottom Of Stove Unit
Door Catch Bolt With Adjustable Hex Nuts Hole
Leg Hole
Bottom Of Stove Unit
Leg Hole
Figure 5 - Removing Back Panel
Top of Stove Unit
Front of Stove Unit
Drop Cloth/ Blanket
Figure 6 - Laying Down Stove On Side (Stove Style May Vary Depending on Model)
For more information, visit www.desatech.com
For more information, visit www.desatech.com
Pallet Wood Bolted to Stove Body Bottom
Front of Stove Unit
Top of Stove Unit
104463-01E
Page 9
INSTALLATION
Continued
INSTALLATION
Stove Cavity Assembly (Cont.)
Stove Cavity Assembly (Cont.)
INSTALLATION
9
9
9. Fasten stove bottom to stove with four (4) M6 x 1 - 25mm bolts. Use a flat washer and lock washer with each bolt. Tighten bolts into threaded holes on stove body (see Figure 10 and Figure 8 on page 8). Use an adjustable wrench or a 10mm socket.
10. Attach stove door by inserting step bolt through door hinge pivot holes and into threaded hole in stove body (see Figure
11). Use an adjustable wrench or a 12mm socket to fasten step bolt. Tighten step bolt until snug. Make sure door moves freely .
11. Install door catch bolt (M8 x 1.25-55mm with two M8 hex nuts) into threaded hole on stove body (see Figure 8, page 8). Use an adjustable wrench or a 12mm socket. The catch bolt has two hex nuts attached to it (see Figure 12). The top nut is a bolt stop and the bottom nut is for door leveling adjustment.
Bolt
Leg
12. Check general catch bolt alignment with door claw. Make fi­nal adjustment and door leveling after stove is in normal stand­ing position.
13. Carefully lift stove back up on its four attached legs.
14. If available, install gas log heater inside stove cavity before installing the back panel (see Installing Gas Log Heater Into Stove, page 10).
15. Fasten back panel to stove with six (6) M6 x 1 - 20mm bolts and washers. Make sure product identification label is located on the outside in lower left-hand corner.
Stove Door
Threaded Hole
Door Hinge
Stove Door
Bolt Shoulder
Door Hinge
Figure 9 - Attaching Stove Legs
Washers
Bolt
Stove Bottom
Figure 10 - Attaching Stove Bottom
Bottom Of Stove Unit
Bottom Of Stove Unit
Step Bolt
Step Bolt
Figure 11 - Attaching Stove Door (Appearance May Vary Depending on Model)
Figure 12 - Catch Bolt and Door Claw Orientation
Bolt Shoulder
Stove Bottom
Bolt Stop
Door
Adjusting Nut
Door Claw
Catch Bolt
For more information, visit www.desatech.com
For more information, visit www.desatech.com
104463-01E
Page 10
INSTALLATION
10
Installing Gas Log Heater Into Stove
INSTALLATION
Continued
INSTALLING GAS LOG HEATER INTO STOVE
1. Remove log and gas log heater from carton. up gas log heater by the burner itself. This could damage heater . Always handle the gas log heater by the heater base only.
2. Remove all protective packaging applied to log and gas log heater for shipment.
3. Check all items for any shipping damage. If damaged, promptly inform dealer where you bought heater.
4. If not already removed, remove back panel from assembled stove body (see Figure 5, page 8). Use an adjustable wrench or a 10 mm socket. Remove six (6) bolts and washers. Keep bolts and washers to reattach back panel later.
5. Set gas log heater inside stove (see Figure 13). Make sure control knob extensions pass through bottom front opening.
6. Align outside holes on heater base with four (4) mounting holes on the stove bottom (see Figure 13).
7. Fasten heater base to stove bottom with #10-24 x .50 bolts and hex nuts provided with gas log heater (see Figure 14). Attach­ment hardware is factory packed inside plastic bag with instal­lation manual and owner’s registration card. Push bolt through heater base mounting hole and through stove bottom. Connect hex nut to bolt on underside of stove bottom. The bolt hex head is for a 5/16" socket and the hex nuts are for a 3/8" socket. If sockets are not available, use adjustable wrenches.
8. Set one-piece log on heater base as shown in Figure 15. Make sure middle section at bottom of log is seated into "U" shaped cutout in center of heater base. Log will fit securely on base.
IMPORTANT:
Make sure log does not cover any burner ports
and does not touch the stove cavity (see Figure 16).
9. Fasten back panel to stove with six (6) M6 x 1.20mm bolts and washers. Make sure product identification label is located on the outside lower left-hand corner.
10. Place freestanding stove in desired position in room. Be sure to maintain clearances to combustibles as outlined on page 7.
Note:
Do not pick
Heater
Bolt
Hex Nut
Figure 14 - Fastening Heater Base to Stove Drop Bottom
Heater Base
Figure 15 - Installing One-Piece Stove Log Set
One-Piece Log Set
O
L
HI
OFF
PILOT
Burner Porting Areas (double slotted rectangular openings
Base
Stove Bottom
One-Piece Log Set
Middle Section at Bottom of Log Set
Burner
"U" Shaped Cutout in Chassis
Bottom Front Opening
Figure 13 - Placing Heater Base In Stove Cavity (Appearance May Vary Depending on Model)
Bolt
Heater Base
For more information, visit www.desatech.com
For more information, visit www.desatech.com
Burner
Safety Pilot Location
Figure 16 - Top View of One-Piece Log Set on Gas Log Heater
Stove Bottom
104463-01E
Page 11
INSTALLATION
Continued
Connecting to Gas Supply
INSTALLATION
11
11
CONNECTING TO GAS SUPPLY
WARNING: This appliance requires a 1/2" NPT (National Pipe Thread) inlet connection to the pres­sure regulator.
WARNING: A qualified service person must con­nect heater to gas supply. Follow all local codes.
Installation Items Needed
Before installing heater, make sure you have the items listed below.
• piping (check local codes)
• sealant (resistant to propane/LP gas)
• equipment shutoff valve *
• test gauge connection *
• sediment trap
• tee joint
• pipe wrench * A CSA design-certified equipment shutoff valve with 1/8" NPT
tap is an acceptable alternative to test gauge connection. Purchase the optional CSA design-certified equipment shutoff valve from your dealer. See Accessories, page 19.
The gas inlet connection for the stove heater is located on the lower right-hand side of the stove when viewed from the front of the unit. The gas connection can be made either through the bottom right side or through the lower back opening as illustrated in Figure 17. Make sure gas log heater is secured to the stove cavity assembly.
WARNING: Never connect heater to private (non­utility) gas wells. This gas is commonly known as wellhead gas.
Side View
Front of Stove Unit
Figure 17 - Gas Regulator Location and Gas Line Access Into Stove Cabinet
Back Stove Panel
Product Identification Label
Gas Inlet Connection Access
Back View
Gas Log Heater
CAUTION: Use only new, black iron or steel pipe. Internally-tinned copper tubing may be used in certain areas. Check your local codes. Use pipe of 1/2" diam­eter or greater to allow proper gas volume to heater. If pipe is too small, undue loss of volume will occur.
Installation must include a equipment shutoff valve, union, and plugged 1/8" NPT tap. Locate NPT tap within reach for test gauge hook up. NPT tap must be upstream from heater (see Figure 18).
IMPORTANT:
Install equipment shutoff valve in an accessible location. The equipment shutoff valve is for turning on or shutting off the gas to the appliance.
Check your building codes for any special requirements for locating equipment shutoff valve to fireplaces.
Apply pipe joint sealant lightly to male NPT threads. This will prevent excess sealant from going into pipe. Excess sealant in pipe could result in clogged heater valves.
WARNING: Use pipe joint sealant that is resistant
to liquid petroleum (LP) gas.
We recommend that you install a sediment trap in supply line as shown in Figure 18. Locate sediment trap where it is within reach for cleaning. Install in piping system between fuel supply and heater. Locate sediment trap where trapped matter is not likely to freeze. A sediment trap traps moisture and contaminants. This keeps them from going into heater controls. If sediment trap is not installed or is installed wrong, heater may not run properly.
CAUTION: Avoid damage to regulator. Hold gas regulator with wrench when connecting it to gas piping and/or fittings.
From Gas Meter (5" W.C.** to
10.5" W.C. Pressure)
Tee Joint Pipe Nipple Cap
Sediment Trap
Figure 18 - Gas Connection
CSA Design-Certified Equipment Shutoff Valve With 1/8" NPT Tap*
Approved Flexible Gas Hose (if allowed by local codes)
3" Minimum
Gas Regulator
* Purchase the optional CSA design-certified equipment shutoff
valve from your dealer. See Accessories, page 19.
**Minimum inlet pressure for purpose of input adjustment.
For more information, visit www.desatech.com
For more information, visit www.desatech.com
104463-01E
Page 12
N T
O S
INSTALLATION
12
Checking Gas Connections
INSTALLATION
Continued
CHECKING GAS CONNECTIONS
WARNING: Test all gas piping and connections , internal and external to unit, for leaks after installing or servicing. Correct all leaks at once.
WARNING: Never use an open flame to check for a leak. Apply a noncorrosive leak detection fluid to all joints. Bubbles forming show a leak. Correct all leaks at once.
Pressure Testing Gas Supply Piping System
Test Pressures In Excess Of 1/2 PSIG (3.5 kPa)
1. Disconnect appliance with its appliance main gas valve (control valve) and equipment shutoff valve from gas supply piping sys­tem. Pressures in excess of 1/2 psig will damage heater regulator.
2. Cap off open end of gas pipe where equipment shutoff valve was connected.
3. Pressurize supply piping system by either using compressed air or opening main gas valve located on or near gas meter.
4. Check all joints of gas supply piping system. Apply noncorrosive leak detection fluid to gas joints. Bubbles forming show a leak.
5. Correct all leaks at once.
6. Reconnect heater and equipment shutoff valve to gas supply. Check reconnected fittings for leaks.
Test Pressures Equal To or Less Than 1/2 PSIG (3.5 kPa)
1. Close equipment shutoff valve (see Figure 19).
2. Pressurize supply piping system by either using compressed air or opening main gas valve located on or near gas meter.
3. Check all joints from gas meter to equipment shutoff valve (see Figure 19). Apply noncorrosive leak detection fluid to gas joints. Bubbles forming show a leak.
4. Correct all leaks at once.
Pressure Testing Heater Gas Connections
1. Open equipment shutoff valve (see Figure 19).
2. Open main gas valve located on or near gas meter.
3. Make sure control knob of heater is in the OFF position.
4. Check all joints from equipment shutoff valve to control valve (see Figure 20). Apply noncorrosive leak detection fluid to gas joints. Bubbles forming show a leak.
5. Correct all leaks at once.
6. Light heater (see Operating Heater, page 13). Check all other internal joints for leaks.
7. Turn off heater (see To Turn Off Gas to Appliance, page 13).
Equipment Shutoff Valve
Gas Meter
Control Valve Location
Figure 20 - Checking Gas Joints
O
Open
Equipment Shutoff Valve
Figure 19 - Equipment Shutoff Valve
For more information, visit www.desatech.com
For more information, visit www.desatech.com
POSI
PO
Closed
104463-01E
Page 13
OPERATING HEATER
OPERATING HEATER
For Your Safety Read Before Lighting
Lighting Instructions
To Turn Off Gas To Appliance
Thermostat Control Operation
13
13
FOR YOUR SAFETY
READ BEFORE LIGHTING
WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing prop­erty damage, personal injury or loss of life.
A. This appliance has a pilot which must be lighted by hand.
When lighting the pilot, follow these instructions exactly.
B. BEFORE LIGHTING smell all around the appliance area
for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electric switch; do not use any phone in your building.
• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
If you cannot reach your gas supplier, call the fire department.
C. Use only your hand to push in or turn the gas contr ol knob.
Never use tools. If the knob will not push in or turn by hand, don’t try to repair it, call a qualified service techni­cian or gas supplier. Force or attempted r epair may r esult in a fire or explosion.
D. Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.
6. With control knob pressed in, press and release ignitor but­ton. This will light pilot. The pilot is attached to the front burner . If needed, keep pr essing ignitor button until pilot lights.
Note:
If pilot does not stay lit, contact a qualified service
person or gas supplier for repairs. Until repairs ar e made, light pilot with match. T o light pilot with ma tch, see Manual Lighting Procedure on page 14.
7. Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob.
• If control knob does not pop out when released, contact
a qualified service person or gas supplier for repairs.
Note:
If pilot goes out, repeat steps 3 through 7. This heater
has a safety interlock system. Wait one (1) minute for sys­tem to reset before lighting pilot again.
8. Tur n control knob counterclockwise ing level. The burners should light. Set control knob to any heat level between HI and LO.
Ignitor Button
Figure 21- Control Knob and Ignitor Button Location
Thermocouple
Figure 22 - Pilot
C-clockwise
to desired heat-
Pilot Burner
Control Knob
LIGHTING
INSTRUCTIONS
NOTICE: During initial operation of new heater, burning logs will give off a paper-burning smell. Orange flame will also be present. This will only last a few hours.
1. STOP! Read the safety information, above.
2. Make sure equipment shutoff valve is fully open.
3. Turn control knob clockwise to the OFF position.
4. Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Fol­low “B” in the safety information, above. If y ou don’t smell gas, go to the next step.
5. Turn control knob counterclockwise LOT position. Press in control knob for five (5) seconds (see Figure 21).
Note:
You may be running this heater for the first time after hooking up to gas supply . If so, the contr ol knob may need to be pressed in for 30 seconds or more. This will al­low air to bleed from the gas system.
For more information, visit www.desatech.com
For more information, visit www.desatech.com
104463-01E
C-clockwise
to the PI-
TO TURN OFF GAS
TO APPLIANCE
Shutting Off Heater
Turn control knob clockwise to the OFF position.
Shutting Off Burners Only (pilot stays lit)
Turn control knob clockwise to the PILOT position.
THERMOSTAT
CONTROL OPERATION
The thermostat control knob can be set to any comfort level between HI and LO. The thermostat will gradually modulate the heat output and flame height from higher to lower settings, or pilot, in order to maintain the comfort level you select. The ideal comfort setting will vary by household depending upon the amount of space to be heated, the output of the central heating system, etc.
Note:
Selecting the HI setting with the control knob will cause the
burner to remain fully on, without modulating down in most cases.
Page 14
14
OPERATING HEATER
Manual Lighting Procedure
INSPECTING BURNERS CLEANING AND MAINTENANCE
Cleaning Burner Injector Holder and Pilot Air Inlet Hole
OPERATING HEATER
Continued
MANUAL LIGHTING
PROCEDURE
1. Follow steps 1 through 5 under Lighting Instructions, page 13.
2. Depress control knob and light pilot with match.
3. Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob. Now follow step 8, Lighting Instructions, page 13.
INSPECTING BURNERS
Check pilot flame pattern and burner flame patterns often.
PILOT FLAME PATTERN
Figure 23 shows a correct pilot flame pattern. Figure 24 shows an incorrect pilot flame pattern. The incorrect pilot flame is not touching the thermocouple. This will cause the thermocouple to cool. When the thermocouple cools, the heater will shut down.
If pilot flame pattern is incorrect, as shown in Figure 24
• turn heater off (see To Turn Off Gas to Appliance, page 13)
• see Troubleshooting, pages 16 through 18
Note:
The pilot flame on natural gas units will have a slight curve,
but flame should be blue and have no yellow or orange color.
Thermocouple
Figure 23 - Correct Pilot Flame Pattern
Pilot Burner
Thermocouple
Figure 24 - Incorrect Pilot Flame Pattern
Pilot Burner
CLEANING AND MAINTENANCE
WARNING: Turn off heater and let cool before
cleaning.
CAUTION: You must keep control areas, burner, and circulating air passageways of heater clean. Inspect these areas of heater before each use. Have heater inspected yearly by a qualified service person. Heater may need more frequent cleaning due to excessive lint from carpeting, pet hair, bedding material, etc.
CLEANING BURNER INJECTOR HOLDER AND PILOT AIR INLET HOLE
The primary air inlet holes allow the proper amount of air to mix with the gas. This provides a clean burning flame. Keep these holes clear of dust, dirt, lint, and pet hair. Clean these air inlet holes prior to each heating season. Blocked air holes will create soot. We recommend that you clean the unit every three months during operation and have heater inspected yearly by a qualified service person.
We also recommend that you keep the burner tube and pilot assembly clean and free of dust and dirt. To clean these parts we recommend using compressed air no greater than 30 PSI. Your local computer store, hardware store, or home center may carry com­pressed air in a can. You can use a vacuum cleaner in the blow position. If using compressed air in a can, please follow the direc­tions on the can. If you don't follow directions on the can, you could damage the pilot assembly. grates of your stove will make cleaning easier.
1. Shut off the unit, including the pilot. Allow the unit to cool for at least thirty minutes.
2. Inspect burner, pilot, and primary air inlet holes on injector holder for dust and dirt (see Figure 25).
3. Blow air through the ports/slots and holes in the burner.
Note:
Removing the rear panel and top
For more information, visit www.desatech.com
For more information, visit www.desatech.com
Injector Holder
Burner Tube
Primary Air Inlet Holes (Shape of Holes May Vary by Model)
Figure 25 - Injector Holder On Outlet Burner Tube
(May Be Brass or Aluminum Depending on Model)
104463-01E
Page 15
CLEANING AND MAINTENANCE
Continued
CLEANING AND MAINTENANCE
Logs
Main Burner
SPECIFICATIONS
15
15
4. Check the injector holder located at the end of the burner tube again. Remove any large particles of dust, dirt, lint, or pet hair with a soft cloth or vacuum cleaner nozzle.
5. Blow air into the primary air holes on the injector holder.
6. In case any large clumps of dust have now been pushed into the burner repeat steps 3 and 4.
Clean the pilot assembly also. A yellow tip on the pilot flame indicates dust and dirt in the pilot assembly. There is a small pilot air inlet hole about two inches from where the pilot flame comes out of the pilot assembly (see Figure 26). With the unit off, lightly blow air through the air inlet hole. You may blow through a drinking straw if compressed air is not available.
Ports/Slots
Burner Tube
Pilot Assembly
Pilot Air Inlet Hole
LOGS
• If you remove logs for cleaning, refer to Installing Gas Log Heater into Stove, page 10, to properly replace logs.
• Replace log(s) if broken or chipped (dime-sized or larger).
MAIN BURNER
Periodically inspect all burner flame holes with the heater running. All slotted burner flame holes should be open with yellow flame present. All round burner flame holes should be open with a small blue flame present. Some burner flame holes may become blocked by debris or rust, with no flame present. If so, turn off heater and let cool. Remove blockage. Blocked burner flame holes will create soot.
SPECIFICATIONS
Btu (Variable) 16,000/30,000 Type Gas Natural Gas Only Ignition Piezo Pressure Manifold 3.5" W.C. Inlet Gas Pressure (in. of water)
Maximum 10.5"
Minimum* 5" Shipping Weight 28 lbs. * For input adjustment
Figure 26 - Pilot Inlet Air Hole
For more information, visit www.desatech.com
For more information, visit www.desatech.com
104463-01E
Page 16
TROUBLESHOOTING
16
TROUBLESHOOTING
Note:
For additional help, visit DESA
International’s technical service web site at www.desatech.com.
Note:
All troubleshooting items are listed in
order of operation.
WARNING: Turn off heater and let cool before servicing. Only a qualified service person should service and repair heater.
CAUTION: Never use a wire, needle, or similar object to clean ODS/pilot. This can damage ODS/ pilot unit.
OBSERVED PROBLEM
When ignitor button is pressed, there is no spark at ODS/pilot
When ignitor button is pressed, there is spark at ODS/pilot but no ignition
ODS/pilot lights but flame goes out when control knob is released
POSSIBLE CAUSE
1. Ignitor electrode not connected to igni­tor cable
2. Ignitor cable pinched or wet
3. Broken ignitor cable
4. Bad piezo ignitor
5. Ignitor electrode broken
6. Ignitor electrode positioned wrong
1. Gas supply turned off or equipment shutoff valve closed
2. Control knob not in PILOT position
3. Control knob not pressed in while in PILOT position
4. Air in gas lines when installed
5. ODS/pilot is clogged
6. Gas regulator setting is not correct
1. Control knob not fully pressed in
2. Control knob not pressed in long enough
3. Equipment shutoff valve not fully open
4. Pilot flame not touching thermocouple, which allows thermocouple to cool, causing pilot flame to go out. This prob­lem could be caused by one or both of the following: A) Low gas pressure B) Dirty or partially clogged ODS/pilot
5. Thermocouple connection loose at con­trol valve
6. Thermocouple damaged
7. Control valve damaged
REMEDY
1. Reconnect ignitor cable
2. Free ignitor cable if pinched by any metal or tubing. Keep ignitor cable dry
3. Replace ignitor cable
4. Replace piezo ignitor
5. Replace pilot assembly
6. Replace pilot assembly
1. Turn on gas supply or open equipment shutoff valve
2. Turn control knob to PILOT position
3. Press in control knob while in PILOT position
4. Continue holding down control knob. Re­peat igniting operation until air is removed
5. Clean ODS/pilot (see Cleaning and Maintenance, pages 14 and 15) or re­place ODS/pilot assembly
6. Replace gas control
1. Press in control knob fully
2. After ODS/pilot lights, keep control knob pressed in 30 seconds
3. Fully open equipment shutoff valve
4. A) Contact local natural gas company
B) Clean ODS/pilot (see Cleaning and Maintenance, pages 14 and 15) or re­place ODS/pilot assembly
5. Hand tighten until snug, then tighten 1/4 turn more
6. Replace pilot assembly
7. Replace control valve
For more information, visit www.desatech.com
For more information, visit www.desatech.com
104463-01E
Page 17
TROUBLESHOOTING
Continued
TROUBLESHOOTING
17
17
OBSERVED PROBLEM
Burner does not light after ODS/pilot is lit
Delayed ignition burner
Burner backfiring during combustion
Slight smoke or odor during initial operation
Moisture/condensation noticed on windows
POSSIBLE CAUSE
1. Burner orifice clogged
2. Inlet gas pressure is too low
1. Manifold pressure is too low
2. Burner orifice clogged
1. Burner orifice is clogged or damaged
2. Damaged burner
3. Gas regulator defective
1. Not enough air
2. Gas regulator defective
3. Residues from manufacturing processes and logs curing
1. Not enough combustion/ventilation air
REMEDY
1. Clean burner (see Cleaning and Main­tenance, pages 14 and 15) or replace
burner orifice
2. Contact local natural gas company
1. Contact local natural gas company
2. Clean burner (see Cleaning and Main- tenance, pages 14 and 15) or replace burner orifice
1. Clean burner (see Cleaning and Main- tenance, pages 14 and 15) or replace burner orifice
2. Replace damaged burner
3. Replace gas control
1. Check burner for dirt and debris. If found, clean burner (see Cleaning and Maintenance, pages 14 and 15)
2. Replace gas control
3. Problem will stop after a few hours of operation
1. Refer to Air for Combustion and Venti- lation requirements (page 4)
Heater produces a whistling noise when burner is lit
Dark residue on logs or inside of fireplace
White powder residue forming within burner box or on adjacent walls or furniture
For more information, visit www.desatech.com
For more information, visit www.desatech.com
104463-01E
1. Turning control knob to HI position when burner is cold
2. Air in gas line
3. Air passageways on heater blocked
4. Dirty or partially clogged burner orifice
1. Improper log placement
2. Drafts or other air currents affecting flame pattern
3. Air holes at burner inlet blocked
4. Burner flame holes blocked
1. When heated, vapors from furniture pol­ish, wax, carpet cleaners, etc. may turn into white powder residue
1. Turn control knob to LO position and let warm up for a minute
2. Operate burner until air is removed from line. Have gas line checked by local natural gas company
3. Observe minimum installation clear­ances (see page 7)
4. Clean burner (see Cleaning and Main- tenance, pages 14 and 15) or replace burner orifice
1. Properly locate logs (see Installing Gas Log Heater Into Stove, page 10 )
2. Eliminate source of drafts around heater
3. Clean out air holes at burner inlet. Peri­odically repeat as needed
4. Remove blockage
1. Turn heater off when using furniture polish, wax, carpet cleaners, or similar products
Page 18
TROUBLESHOOTING
18
TROUBLESHOOTING
Continued
WARNING: If you smell gas
Shut off gas supply.
Do not try to light any appliance.
Do not touch any electrical switch; do not use any phone in
your building.
Immediately call your gas supplier from a neighbors phone. Follow the gas suppliers instructions.
If you cannot reach your gas supplier, call the fire department.
IMPORTANT:
Cleaning supplies, paint, paint remover, cigarette smoke, cements and glues, new carpet or textiles, etc., create fumes. These fumes may mix with combustion air and create odors. These odors will disappear over time.
OBSERVED PROBLEM
Heater produces a clicking/ticking noise just after burner is lit or shut off
Heater produces unwanted odors
Heater shuts off in use (ODS operates)
Gas odor even when control knob is in OFF position
Operating heater where impurities in air exist may create odors.
POSSIBLE CAUSE
1. Metal expanding while heating or con­tracting while cooling
1. Heater burning vapors from paint, hair spray, glues, cleaners, chemicals, new carpet, etc. (See ment above)
2. Gas leak. See Warning statement at
top of page
1. Not enough fresh air is available
2. Low line pressure
3. ODS/pilot is partially clogged
1. Gas leak. See Warning statement at
top of page
2. Control valve defective
IMPORTANT
state-
REMEDY
1. This is common with most heaters. If noise is excessive, contact qualified ser­vice person
1. Open window and ventilate room. Stop using odor causing products while heater is running
2. Locate and correct all leaks (see Check- ing Gas Connections, page 12)
1. Open window and/or door for ventilation
2. Contact local natural gas company
3. Clean ODS/pilot (see Cleaning and Maintenance, pages 14 and 15)
1. Locate and correct all leaks (see Check- ing Gas Connections, page 12)
2. Replace control valve
Gas odor during combustion
For more information, visit www.desatech.com
For more information, visit www.desatech.com
1. Foreign matter between control valve and burner
2. Gas leak. See Warning statement at
top of page
1. Take apart gas tubing and remove for­eign matter
2. Locate and correct all leaks (see Check- ing Gas Connections, page 12)
104463-01E
Page 19
SERVICE HINTS
TECHNICAL SERVICE
REPLACEMENT PARTS
ACCESSORIES
19
19
SERVICE HINTS
When Gas Pressure Is Too Low
• pilot will not stay lit
• burners will have delayed ignition
• heater will not produce specified heat You may feel your gas pressure is too low. If so, contact your local
natural gas supplier.
TECHNICAL SERVICE
You may have further questions about installation, operation, or troubleshooting. If so, contact DESA International’s Technical Ser­vice Department at 1-866-672-6040. When calling, please have your model and serial numbers of your heater ready.
You can also visit DESA International’s technical service web site at www.desatech.com.
REPLACEMENT PARTS
Note:
Use only original replacement parts. This will protect your
warranty coverage for parts replaced under warranty.
PARTS UNDER WARRANTY
Contact authorized dealers of this product. If they can’t supply original replacement part(s), call DESA International’s Technical Service Department at 1-866-672-6040.
When calling DESA International, have ready
• your name
• your address
• model and serial numbers of your heater
• how heater was malfunctioning
• type of gas used (propane/LP or natural gas)
• purchase date Usually, we will ask you to return the part to the factory.
ACCESSORIES
Purchase these heater accessories from your local dealer. If they can not supply these accessories, call DESA International at 1-866-672-6040 for referral information. You can also write to the address listed on the back page of this manual.
EQUIPMENT SHUTOFF VALVE - GA5010
For all models. Equipment shutoff valve with 1/8" NPT tap. Fits 1/2" NPT pipe.
CLEANING KIT - CCK
(Not Shown)
For all models. Your vent-free gas appliance requires regular cleaning and maintenance to prevent performance problems. This kit gives you the tools and instructions to make it easy to clean all critical areas of your appliance.
INFORMATION VIDEO - 108917-01
For all models. A care and maintenance video is available by calling 1-866-672-6040.
PARTS NOT UNDER WARRANTY
Contact authorized dealers of this product. If they can’t supply original replacement part(s), either contact your nearest Parts Cen­tral (see page 24) or call DESA International at 1-866-672-6040 for referral information.
When calling DESA International, have ready
• model number of your heater
• the replacement part number
For more information, visit www.desatech.com
For more information, visit www.desatech.com
104463-01E
Page 20
ILLUSTRATED PARTS BREAKDOWN
20
SL30NT
ILLUSTRATED PARTS BREAKDOWN
SL30NT
1
17
9
8
18
3
15
10
12
13
2
7
6
5
11
15
18
4
14
16
For more information, visit www.desatech.com
For more information, visit www.desatech.com
18
104463-01E
Page 21
PARTS LIST
SL30NT
This list contains replaceable parts used in your stove. For replacement parts see Replacement Parts on page 19 of this manual.
KEY PART NO. NO. DESCRIPTION QTY.
1 104026-01 Stove Log 1 2 098249-01 Nut, M5 2 3 ** Painted Base Assembly 1 4 104454-01 Bracket, Regulator 1 5 098867-14 Gas Regulator 1 6 104425-01 Inlet Tube 1 7 104424-01 Outlet Burner Tube 1 8 099056-26 Burner Orifice Injector 1 9 111124-01 Burner Retainer Spring 1 10 102980-01 Burner 1 11 101329-21 Control Valve 1 12 104472-01 Bracket 1 13 099211-01 Screw 2 14 102445-01 Piezo Ignitor 1 15 099387-13 Pilot Tube 1 16 098271-10 Ignitor Cable 1 17 104285-01 ODS Pilot (NG) 1 18 M11084-38 Screw, Hex Head (#8-18 x .38) 7
PARTS LIST
SL30NT
21
21
PARTS AVAILABLE NOT SHOWN
100563-01 Warning Plate 1 101054-01 Lighting Instructions Plate 1 100565-01 Warning Plate Fastener 1 101137-04 Hardware Kit 1
** Not a field replaceable part.
For more information, visit www.desatech.com
For more information, visit www.desatech.com
104463-01E
Page 22
ILLUSTRATED PARTS BREAKDOWN
22
CISC and CISG
ILLUSTRATED PARTS BREAKDOWN
CISC CISG
1L
1C
7
1R
4
5-4
5-1
6
5-4
4
2
3
5-2
5-3
For more information, visit www.desatech.com
For more information, visit www.desatech.com
104463-01E
Page 23
PARTS LIST
CISC CISG
This list contains replaceable parts used in your stove. For replacement parts see Replacement Parts on page 19 of this manual.
KEY PART NO. NO. DESCRIPTION QTY.
1L 104171-06 Top Grate with Screen - Left (Black Only) 1 1C 104171-05 Top Grate with Screen - Center (Black Only) 1 1R 104171-07 Top Grate with Screen - Right (Black Only) 1 2 104969-01 Bottom Door (Charcoal) 1
104969-02 Bottom Door (Forest Green) 1 3 104174-03 Stove Dropped Bottom 1 4 104970-01 One Leg (Charcoal) (4 Total Per Stove) 1
104970-02 One Leg (Forest Green) (4 Total Per Stove) 1 5 104971-01 Hardware Kit 1 5-1 * Door Hinge Step Bolt With Shoulder (1 Per Unit) 1 5-2 * Door Catch Bolt M8 x 1.25 - 55mm Long With Two M8
Hex Nuts (1 Per Unit) 1
5-3 * Bottom Floor Bolts M6 x 1 - 25mm Long With Flat Washer
And Lock Washer (4 Per Unit) 1
5-4 * Leg Attachment Stud, Headless, Slotted,
M10 x 1.5 - 40mm Long 4
6 104178-01 Back Panel Bolts M6 x 1 - 20mm Long With Flat Washer
And Lock Washer (6 Per Unit) 1
7 104968-01 Stove Back Panel (Black Only) 1
PARTS LIST
CISC and CISG
23
23
104463-01E
PARTS AVAILABLE NOT SHOWN
104108-08 Touch-up Spray Paint 12 oz Can (Charcoal) 1
104108-05 Touch-up Spray Paint 12 oz Can (Forest Green) 1
* Included In Hardware Kit
For more information, visit www.desatech.com
For more information, visit www.desatech.com
Page 24
24
PARTS CENTRALS
PARTS CENTRALS
These Parts Centrals are privately owned businesses. They have agreed to support our customer’s needs by providing original replacement parts and accessories.
Baltimore Electric
1348 Dixwell Avenue Hamden, CT 06514-0322 1-800-397-7553 203-248-7553 Parts Department
Portable Heater Parts
342 N. County Rd. 400 East Valparaiso, IN 46383-9704 All States 219-462-7441 1-888-619-7060 sales@portableheaterparts.com techservice@portableheaterparts.com
FBD
1349 Adams Street Bowling Green, KY 42103-3414 270-846-1199 1-800-654-8534 Fax: 1-800-846-0090 franktalk@aol.com
Master Parts Dist.
1251 Mound Ave NW Grand Rapids, MI 49504-2672 616-791-0505 1-800-446-1446 Fax: 616-791-8270 www.nbmc.com
East Coast Energy Products
707 Broadway W. Long Branch, NJ 07764-1542 732-870-8809 1-800-755-8809 www.njplaza.com/ecep
Halco Enterprises
208 Carter Drive, Unit 21 West Chester, PA 19382-4500 610-430-7717 1-800-368-0803 www.halcoenterprises.com
Laportes Parts & Service
2444 N. 5th Street Hartsville, SC 29550-7704 843-332-0191 Parts Department
Cans Unlimited, Inc.
P.O. Box 645 Taylor, SC 29687-0013 All States 803-879-3009 1-800-845-5301 cuisales@aol.com
Washer Equipment Co.
1715 Main Street Kansas City, MO 64108-2195 KS, MO, AR 816-842-3911 www.washerparts.com
For more information, visit www.desatech.com
For more information, visit www.desatech.com
104463-01E
Page 25
y
OWNER'S REGISTRATION FORM
In order to provide better customer service for this and future purchases, we recommend that you register your product with us.
ACCESSORIES
You can register online at www.desatech.com. If access to our website is not available to you, please complete this Owners Registration Form and mail to the address on the back of this owners manual. Please provide the following product information:
Brand: Model: Date Purchased: Serial Number:
(Comfort Glow, Vanguard, etc.) (EFP33PR, VTGH33NR, etc.)
Note:
Keep receipt for warranty verification.
7 or 9 digit number located on product or identification tag.
First Name: Last Name: Address: City: State: Zip: Country: Home Phone: ( ) - E-Mail:
Please answer the following questions to register your product with DESA International:
1. Where will the product be used? ❍ Living/Family Room ❍ Office/Warehouse ❍ Utility Shed/Outbuilding ❍ Garage ❍ Bedroom ❍ Bathroom ❍ Other
2. If you bought this product yourself, did you plan to purchase this type of product before going into the store? Yes ❍ No
3. Who selected the product? Male Female Both
4. What is the population of your area? Under 10,000 10,000 to 25,000 25,000 to 50,000 50,000 to 100,000 ❍ 100,000 to 250,000 ❍ Over 250,000
5. What is your primary source of heat? Propane (LP Gas) ❍ Fuel Oil ❍ Wood Natural Gas ❍ Electric ❍ Other
6. How was the product installed? ❍ Professional Installer ❍ Self ❍ Other
7. Cost of product excluding sales tax? $___________________
8. Cost to install product? $____________________
9. Type of store where product was purchased? Hardware Propane Dealer ❍ Natural Gas/Utility Co. ❍ Home Center/Builders Suppl ❍ Fireplace or Hearth Shop ❍ Farm Store ❍ Other
10. What motivated you to buy this product? Sudden Cold Weather Replace Older Model ❍ D.I.Y. Home Project ❍ Emergency Back-Up Heat ❍ Heater was on Sale ❍ Energy Savings/High Efficiency ❍ Construction Project ❍ Other
11. How did you learn about this product brand? Advertising Relative or Friend Store Display Other ________________________
12. Level of Education of Purchaser: Some High School Completed High School Completed College Completed Graduate School
13. Age of Purchaser: Under 20 20 - 29 30 - 39 40 - 49 50 - 59 60 or Over
14. Buyers total annual household income: Under $15,000 $15,000 to $19,999 $20,000 to $34,999 $35,000 to $49,999 ❍ $50,000 to $74,999 ❍ $75,000 to $99,999 ❍ $100,000 and Over
15. Store where product was purchased: Name: ______________________________________ City: _______________________ State: __________
16. In choosing this product, how important were the following:
Availability Price Brand Name Overall Quality Heat Output Made in USA Warranty Local Service Value for Price Prior Brand Experience Controls Location Thermostat, Remote, or Manual Operation Ease of Operation Special Features Salespersons Recommendation Friend/Relatives Recommendation Portability
For more information, visit www.desatech.com
For more information, visit www.desatech.com
Quiet Operation
104463-01E
Not Important Somewhat Important Very Important
❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍
❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍
❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍
25
25
Page 26
26
TAPE
TM
2701 Industrial Drive P.O. Box 90004 Bowling Green, KY 42102-9004
Postage
Required
For more information, visit www.desatech.com
For more information, visit www.desatech.com
TAPE
104463-01E
Page 27
NOTES
NOTES
_______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________
27
27
_______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________
For more information, visit www.desatech.com
For more information, visit www.desatech.com
104463-01E
Page 28
28
WARRANTY INFORMATION
KEEP THIS WARRANTY
Model Serial No. Date Purchased
Always specify model and serial numbers when communicating with the factory. We reserve the right to amend these specifications at any time without notice. The only warranty applicable is our standard written warranty. We make
no other warranty, expressed or implied.
LIMITED WARRANTY
VENT-FREE NATURAL GAS LOG HEATERS AND CAST IRON STOVE CHASSIS
DESA International warrants this product to be free from defects in materials and components for two (2) years from the date of first purchase, provided that the product has been properly installed, operated and maintained in accordance with all applicable instructions. To make a claim under this warranty the Bill of Sale or cancelled check must be presented.
This warranty is extended only to the original retail purchaser. This warranty covers only the cost of part(s) required to restore this heater to proper operating condition. Warranty part(s) MUST be obtained through authorized dealers of this product and/or DESA International who will provide original factory replacement parts. Failure to use original factory replacement parts voids this warranty. The heater MUST be installed by a qualified installer in accordance with all local codes and instructions furnished with the unit.
This warranty does not apply to parts that are not in original condition because of normal wear and tear, or parts that fail or become damaged as a result of misuse, accidents, lack of proper maintenance or defects caused by improper installation. Travel, diagnostic cost, labor, transportation and any and all such other costs related to repairing a defective heater will be the responsibility of the owner.
TO THE FULL EXTENT ALLOWED BY THE LAW OF THE JURISDICTION THAT GOVERNS THE SALE OF THE PRODUCT; THIS EXPRESS WARRANTY EXCLUDES ANY AND ALL OTHER EXPRESSED WARRANTIES AND LIMITS THE DURATION OF ANY AND ALL IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE TO TWO (2) YEARS FROM THE DATE OF FIRST PURCHASE; AND DESA INTERNATIONAL’S LIABILITY IS HEREBY LIMITED TO THE PURCHASE PRICE OF THE PRODUCT AND DESA INTERNATIONAL SHALL NOT BE LIABLE FOR ANY OTHER DAMAGES WHATSOEVER INCLUDING INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Some states do not allow a limitation on how long an implied warranty lasts or an exclusion or limitation of incidental or consequential damages, so the above limitation on implied warranties, or exclusion or limitation on damages may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights that vary from state to state. For information about this warranty write:
TM
2701 Industrial Drive P.O. Box 90004 Bowling Green, KY 42102-9004
www.desatech.com
For more information, visit www.desatech.com
For more information, visit www.desatech.com
104463 01
NOT A UPC
104463-01 Rev. E 02/03
104463-01E
Loading...