Comfort Glow QEH1500, QEH1501 Installation Instructions And Homeowner's Manual

-1 -

Model#:QEH1500, QEH1501

Quartz Infrared

Electric Heater

Installation Instructions and Homeowner's Manual

WARNING! IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED EXACTLY, A FIRE

MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.

Comfort Home Products, Inc.
12256 William Penn Hwy, Suite A
Huntingdon, PA 16652
Made in China
Printed in China

COMFORT GLOW PHONE NUMBER: [phone]

http://www.worldmkting.com

FOR YOUR SAFETY

DO NOT STORE

OR USE GASOLINE OR

OTHER FLAMMABLE VAPORS

OR LIQUIDS

IN THE VICINITY OF THIS OR

ANY OTHER APPLIANCE

ANSI/UL 1278. MOVABLE AND WALL-OR CEILING HUNG ELECTRIC ROOM HEATERS

INSTALLER: DO NOT DISCARD THIS MANU AL - LEAVE FOR HOME OWNER

CUSTOMER: PLEASE RETAIN THIS MANUAL FOR FUTURE USE

H

L

H

L

Power

Ti me

Temp

Temp

℃

℉

℃

℉

-2 -

TABLE OF CONTENTS

PLEASE READ THE INSTALLATION & OPERATIONS INSTRUCTIONS

BEFORE USING THIS APPLIANCE

IMPORTANT: Read all instructions and warnings carefully before starting installation.
Failure to follow these instructions may result in a possible electric shock, fire hazard
and will void the warranty.

Table of Contents, Specifications 2

Important Safety Instructions 3

Zone Heat Saves 4

Heater Operation 5

Filter Maintenance 6

Trouble Shooting 6

Replacement Parts List 7

SPECIFICATIONS

Electrical:

V oltage: 120V, 60H Z
Power Consumption: 750W, 1500W (+5%, - 10% tolerance)

Features:

Remote Control
Room Tem perature Display
High & Low Heat Settings
Washable Air Filter

Overheat Protection

Dimensions:

Product Dimensions: H 17.6” x W 13.2” x D18.7”
Box Dimensions: H 20.9” x W 16.5” x D 22.8”
Product Weight: 31.5 lbs.
Shipping Weight: 35.3 lbs.

-3 -

IMPORTANT SAFETY INSTRUCTIONS

PLEASE RETAIN THIS USER’S GUIDE FOR FUTURE RE FERENCE

When using electrical appliances, basic precautions should always be followed to reduce the risk of
fire, electric shock, and injury to person, including following:

1. Read all instructions before using this appliance.

2.

This heater is hot when in use. To avoid burns, do
not let bare skin touch hot surfaces. Th e grill direct ly in
front of the heater outlet becomes hot dur ing heater
operation. Keep combust i ble materials, such as
furniture, pillows, beddin g, paper s, c l ot hes, and
curtains at least 3 feet from the front of the heater and
keep them away from the sides and r ear.

3. CAUTION: Extreme caution is necessary

when any heater is used by or near children or
invalids and whenever the heater is left
operating and unattended.

4. Always unplug heater when not in use.

5. Do not operate any heater with a damaged

cord or plug or after the heater malfunctions,
has been dropped or damaged in any manner.
Return heater to an authorized service facility
for examination, electrical or mechanical
adjustment, or repair.

6. Do not use outdoors.

7. This heater is not intended for use in bathrooms,
laundry areas or similar indoor locations. Never
locate the heater where it may fall into a bathtub or
other water container.

8. Do not run cord under carpeting. Do not cover
cord with throw rugs, runners or similar coverings.
Arrange cord away from traffic areas and where it
will not be tripped over.

9. To disconnect heater, turn controls to off, then
remove plug from outlet.

10. Always connect to properly grounded, fused,
and polarized outlets.

11. Do not insert or allow foreign objects to enter
any ventilation or exhaust opening as this may
cause an electric shock or fire, or damage to the
heater.

12. To prevent a possible fire, do not block air
intakes or exhaust in any manner. Do not use on

soft surfaces, like a bed, where openings may
become blocked.

13. CAUTION: This heater has hot and arcing or
sparking parts inside. Do not use it in areas where
gasoline, paint, or flammable liquids are used or
stored. This heater should not be used as a drying
rack for clothing.

14. Do not modify this heater. Use it only as
described in this manual. Any other use, not
recommended by the manufacturer, may cause fire,
electric shock or injury to persons.

15. Avoid the use of an extension cord because it
may overheat and cause a fire hazard. However if
you have to use an extension cord, the cord shall
be 14

AWG minimum size and rated not less than

1875

watts. Always use the shortest extension cord

that is safe.

16. Always use a certified electrician should new
circuits or outlets been required.

17. Always use ground fault protection where
required by electrical code.

18. Always disconnect power before performing any
cleaning, maintenance or relocation of the heater.

SAVE THESE INSTRUCTIONS!

Grounding

This heater is for use on 120 volts. The cord has a
plug with three blades for proper grounding. DO
NOT attempt to modify the plug in any way or use
adaptors to defeat the purpose of the grounding
feature. Plug ONLY into a receptacle that accepts
three-blade plug.

-4-

ZONE HEATING SAVES!

The concept of Zone Heating is simple. Use High Efficiency heaters to heat the rooms you use most, during
the times you use these areas and turn back the thermostat to your central heating system. To achieve the
maximum benefit it is important to understand your heater and where best to locate it.

Our COMFORT GLOW Infrared Heater provides clean and economical heat by utilizing a two stage heating
process. The heating process of our Infrared Heater draws filtered air into ‘the box” where it is initially
warmed by a resistance heating element. The blower then channels the warm air past the infrared heat
elements boosting the temperature even further. The warm air passes the copper reflector as it exits the
heater further enhancing the heat. When properly located, the fan will project the accumulated warmth
throughout the room.

Please follow these suggestions:

1. Close doors to areas you do not wish to heat.

2. Locate a three prong outlet along an interior wall if possible. Position the heater so that the warm air can

blow unobstructed across the room towards the exterior walls.

3. Check your windows and doors for the infiltration of cold air and insulate as needed to avoid heat loss.

Rapid heat loss will minimize the effectiveness of your Infrared heater as it would any conventional type

heater.

4. Keep t he area around the heater free of obstructions to insure maximum airflow. Keep electrical cords,

drapery , furniture, and ot her combus tibles 3 feet (0.9 M) away from the front of the heater and away from

the sides.

5. Avoid locating your heater in high traffic areas or in direct sunlight.

6. Avoid locating your heater near your central heating thermostat.

-5-

HEATER OPERATION

Plug your Infrared Heater power cord into a 120V, 15am p or 20amp three-bladed receptacle.

Control Panel

Remote Control

To Turn the Heater On: Turn on the main power

on/off switch on the rear panel of the heater. Then

press the Power button

on the control panel or

on the remote control.

To Set the Temperature: Press up

or down

button on the control panel or on the remote

control to the desired temperature. When desired
temperature is reached, the heater will stop heating
automati cal ly. When the temperature drops below the
desired temperature, the heat er w il l come on again.

To Set the Heating Level: Press the heat button

on the control panel or remote control to switch

between high and low heat and the corresponding
High (H) or low (L) LED wi ll be lit.

T o Set Runni ng T ime: Press on the control panel
or remote control, numbers 0 to 8 will appear on

screen. 0 means there is no set running time and
heater will be running continuous ly. Number 1-8 mean
the number of hours that the heater will run before it
automatically stops.

To change betwee n ℃ and ℉: Press

Helpful Tips:

1) If heater will not turn on, check main power switch on r ear of he at er.

2) Check air filter, clean as needed

3) If your room has minimal heat loss, and is closed off to cooler areas you may be able to reduce the cost of

operation by setting the heat er t o low after the room has reached a com f or table temperature.

4) If remote is lost, you can s t ill oper at e t he heater manually.

5) Do not drag your heater across t he r oom by pulling it buy the cord. Stow cord on cord w r ap when not in use.

6) Use the timer to turn off your heater and save ener gy.

7) Cool Down feature: When the thermostat cy cle s “off” or when you turn the un it of f, t he fan w ill cont inue t o run

for a few moments to finis h dist r i but ing the heat and to cool down the inter i or of the heater.

-6-

FILTER MAINTENANCE

Your heater is equipped with a washable filter. For proper operation this filter must be kept clean. If the
heater is used without the filter dirt and dust can accumulate inside and may cause the unit to smell while in
operation or other problems. Use without a filter will void your warranty.

1) WARNING! Make sure the power is turned off before performing any maintenance. Turn off heater, by

using the main power switch on the rear of the unit and unplug the heater.

2) Remove the filter from the rear of the heater.

3) Vacuuming will gener ally clean the filter in most cases.

4) If dirt remains, rinse filter with wa rm tap water thr ough the rea r side of the f ilter (opp osite of air int ake

direction) until clear of dust and debris.

5) If the filter is extremely dirty or clogged with grease, you can soak the filter in a mild solution of dish soap

and water, and repeat sensing process.

6) Shake filter to remove excess water and lay on clean cloth or paper tow els to dry. Do not use heat source

to dry filter.

7) Replace filter in heater ONLY after it is completely dry.

WARNING! Do not use this product if any part has been under water.

TROUBLE SHOOTING

PROBLEM CORRECTIVE ACTION

a. The room temperature is higher than the thermostat setting.

1. Heater does not blow warm air b. Check to be sure unit is on HIGH setting.

a. Check circuit breaker, Reset as needed or plug into a different outlet.

2. No Power to heater b. Make sure main switch on rear of unit is switched to on position.

c. Over heat safety control activated. Remove blockage from filter and around heater.

Unplug heater for 10 to 20 minutes. Unit should then operate normally.

-7-

REPLACEMENT PARTS LIST

Exposed Drawing of Parts – Model# QEH1500 / QEH1501

ITEM DESCRIPTION OEM

01 Filter ND-48/01
02 Power cord and plug ND-48/02
03, 04, 19 Heater/Blower As sembly ND-48/03,04,19
05 Main power switch ND-48/05
06 Metal cabinet ND-48/06
07 Temperature sensor ND-48/07
08 Wooden Box ND-48/08
09 Circuit board ND-48/09
10 Overheat switch ND-48/10
11 Upper heat reflector ND-48/11
12 Front grill ND-48/12
13, 14 Control Assembly with button switches ND-48/13,14
15 Remote Sender ND-48/15
16 Quartz T ube ND-48/16
17 Lower heat reflector “U” ND-48/17
18 Heat chamber ND-48/18
20 Casters ND-48/20