Comfort Glow ES4830, ES4835 Installation Instructions And Homeowner's Manual

ES4830

Installation Instructions and Homeowner's Manual

WARNING! IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED EXACTLY, A FIRE

World Marketing of America, Inc

Mill Creek, PA 17060

FOR YOUR SAFETY

Made in China

COMFORT GLOW PHONE NUMBER: [phone]

ES4835

Freestanding

Electric Stove

MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.

12256 William Penn Hwy
Box 192

DO NOT STORE

OR USE GASOLINE OR

OTHER FLAMMABLE VAPORS

OR LIQUIDS

IN THE VICINITY OF THIS OR

http://www.worldmkting.com

ANY OTHER APPLIANCE

ANSI/UL 1278. MOVABLE AND WALL-OR CEILING HUNG ELECTRIC ROOM HEATERS

DO NOT DISCARD THIS MANUAL - LEAVE FOR HOME OWNER

CUSTOMER: PLEASE RETAIN THIS MANUAL FOR FUTURE USE

TABLE OF CONTENTS

The flame effect is created by a

PLEASE READ THE INSTALLATION & OPERATIONS INSTRUCTIONS BEFORE USING

THIS APPLIANCE

IMPORTANT: Read all instructions and warnings carefully before starting installation.
Failure to follow these instructions may result in a possible electric shock, fire hazard
and will void the warranty.

Table of contents, Specifications 2

Important Safety Instructions 3

Zone Heat Saves, Instructions for Power 4

Assembly, Heater Operation 5-6

Service & Troubleshooting 6-7

Warranty Guidelines 8-9

SPECIFICATIONS: REPLACEMENT LIGHT BULB
Model: ES4830 (Black)
ES4835 (Bronze)

Watt: 1500W Volt: 120V
Heating Element: Heating Wire
3 Color flame
LED flame
Log flame effect
Fire adjustable
Adjustable thermostat

17V-01 LED lamp. If the flame
effect does not work , the bulbs
may have come loose or been
damaged during shipping.

SAFETY FEATURES
Overheat Safety Feature

This appliance comes equipped with an overheat protection safety device. Should the appliance begin to overheat for
any reason, it will automatically turn all heater functions of the appliance off. The appliance will have to be reset prior
to continuing use. To reset the overheat protection safety device, turn all controls off and unplug the appliance. Wait
10 minutes, plug the appliance back in and turn on.

~ 2 ~

INTENDED USE: This product is intended only for indoor household or office use.

IMPORTANT INSTRUCTIONS

It is NOT intended for industrial or commercial use. DO NOT USE OUTDOORS

PLEASE READ AND SAVE THESE IMPORTANT SAFEFTY INSTRUCTIONS When using electrical appliances, basic
precautions should always be followed to reduce the risk of fire, electrical shock, and injury to persons, including
the following:

1. Read all instructions before using this heater.

2. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. If provided, use handles
when moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes and
curtains at least 3 feet (0.9m) from the heater.

3. Extreme caution is necessary when any heater is used by or near children, pets or invalids and whenever the
heater is left operating unattended.

4. If possible always unplug this appliance when not in use.

5. Do not operate any heater with a damaged cord or plug or after the heater malfunctions, has been dropped or
damaged in any manner.

6. Any repairs to this appliance should be carried out by a qualified service person.

7. Under no circumstances should this appliance be modified. Parts having to be removed for servicing must be
replaced prior to operating this appliance again.

8. Do not use outdoors.

9. Use your heater only in dry environments. This heater is not intended for use in bathrooms, laundry areas and
similar indoor locations. Never locate the heater where it may fall into a bathtub or other water container. Do not
use your heater outdoors. Do not use near sinks, swimming pools or other damp areas such as flooded basements,
garages, etc or anyplace where the heater could come in contact with water.

10. Do not use this heater in elevated locations, such as on shelves, raised platforms, etc.

11. Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Arrange
cord away from traffic area and where it will not be tripped over.

12. To disconnect heater, first turn controls to off, then remove plug from outlet. Always unplug the heater when
not in use.

13. Connect to a properly grounded outlets only.

14. This appliance, when installed, must be electrically grounded in accordance with local codes, with the current
CSA C22.0 Canadian Electrical codes or for USA installations, follow local codes or for USA installations, follow local
codes and the National Electric code ANSI/NFPA No. 70.

15. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an
electrical shock or fire, or damage the heater.

16. To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a
bed, where openings may become blocked.

17. This appliance has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint or
flammable liquids are used or stored. This appliance should not be used as a drying rack for clothing, nor should
Christmas stockings or decorations be hung on, or near it.

18. Use this heater only as described in this manual. Any other use not recommended by the manufacturer may
cause fire, electric shock, or injury to persons.

19. Always plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or relocatable
power strip.

20. Do not use this heater with missing, damaged, or broken legs.

21. “SAVE THESE INSTRUCTIONS”

~ 3 ~

ZONE HEATING SAVES!

WARNING: This heater has a voltage rating of

The concept of Zone Heating is simple. Use High Efficiency heaters to heat the rooms you use most, during the
times you use these areas and turn back the thermostat to your central heating system. To achieve the
maximum benefit it is important to understand your heater and where best to locate it.

Please follow these suggestions:

1. Close doors to areas you do not wish to heat.

2. Locate a outlet along an interior wall if possible. Position the heater so that the warm air can blow
unobstructed across the room towards the exterior walls.

3. Check your windows and doors for the infiltration of cold air and insulate as needed to avoid heat loss.
Rapid heat loss will minimize the effectiveness of your heater as it would any conventional type heater.

4. Keep the area around the heater free of obstructions to insure maximum airflow. Keep electrical

cords, drapery, furniture, and other combustibles 3 feet (0.9 M) away from the front of the heater
and away from the sides.

5. Avoid locating your heater in high traffic areas or in direct sunlight.

6. Avoid locating your heater near your central heating thermostat.

INSTRUCTIONS FOR POWER

WARNING: Before servicing this heater be sure to unplug heater from wall outlet. Do

not only turn off heater from the main “ON/OFF” switch, be sure to unplug this heater.

This heater is for use on 120 volts only. The cord has a plug as shown in the following figure.

120 volts. The cord has a plug as shown in A. An
adapter as shown in C is available for connecting
three-blade grounding-type plugs to two-slot
receptacles. The grounding lug extending from the
adapter must be connected to a permanent
ground such as a properly grounded outlet box.
The adapter should not be used if a three-slot
grounded receptacle is available.

DO NOT DEFEAT THE SAFETY PURPOSE OF THE
GROUNDED PLUG.

~ 4 ~

ASSEMBLY

ALWAYS make sure the unit is unplugged before beginning assembly! NEVER move or clean the heater, or
change the bulbs, while it is plugged in.

ALWAYS attach the feet before using! NEVER plug in or operate this unit if the feet are not attached.

Lay stove (A) upside down on a padded surface with the underside accessible. Attach leg (B) to stove by
inserting the tab on the top of the leg (B) into the corresponding slot on the bottom of the stove (A). Insert
two screws (C) into predrilled holes and tighten securely. Repeat with remaining three legs.

OPERATING YOUR HEATER

Once the unit has been properly connected to a grounded electrical outlet, it is ready to operate.
Note: Ensure the circuit breakers for the power supply are turned on.
To access the control panel, slowly open the door located on the front of the heater.

~ 5 ~

THERMOSTAT: This knob controls the thermostat that turns the heat on and off to maintain the
FLAME INTENSITY : This knob controls the brightness of the flame effect. Turn the knob to the

WARNING: Disconnect power and allow unit to cool completely before attempting any

Required Tools: Phillips

Thermostat

Flame Intensity

On/Off

ON: Press the power switch ON. The power indicator light will glow, and the flame
turn on.

OFF: Press the power switch OFF. All functions will turn off.

desired temperature. Turn the knob to the desired setting. The heat will turn on and off
automatically to

(NOTE: If the room temperature is higher than the thermostat setting, the heater will not
turn on.)

right (High) to brighten the flame effect Turn the knob to the left (Low) to dim the flame effect.

(NOTE: The ON/OFF switch turns the flame effect on and off. The flame effect will not turn off
unless the power is turned off.)

maintain the set temperature.

effect will

SERVICE INSTRUCTIONS

maintenance or cleaning to reduce the risk of fire, electrical shock or personal injury.

REPLACING LIGHT BULBS

Access the LED lamp through the rear access panel ( see illustration below).

A. Unplug the power cord from the wall outlet.
B. If the stove has been operating, let the stove cool at least 1 hour.
C. Loosen the screws holding the stove back panel to the main body of stove (see Fig.1).
D. Remove LED lamps and replace with 17V-01 (see Fig.2)
E. Place rear access panel back into position and tighten screws. (Do not over tighten).

Head screwdriver (not

provided)

~ 6 ~

TROUBLE SHOOTING

PROBLEM

POSSIBLE CAUSE

SOLUTION

Turn all controls off, unplug

Turn all controls off, unplug the

restart.

IF YOU EXPERIENCE DIFFICULTIES, PLEASE DO NOT RETURN THIS PRODUCT TO STORE

For assistance with this appliance, please call our customer service department.

No warm air is coming from the
heater

The appliance turns off and will
not turn back on.

The appliance does not turn on
when the button is pushed to
“ON”

Flame is dim or not present

The overheat protection device
in the appliance has been
triggered.

1. The overheat protection
device in the appliance has
been triggered.

2. House circuit breaker has
been tripped.

The overheat protection device
in the appliance has been
triggered

1. Dimmer control knob is
set too low.

2. Light bulb is burnt out.

3. “Flame wand” has come
loose from bracket.

the appliance, allow to cool for
at least 10 min plug back in and
restart.

1.Turn all controls off, unplug
the appliance, allow to cool for
at least 10 min., plug back in
and restart.

2. Reset house circuit breaker.

appliance, allow to cool for at
least 10 min., plug back in and

1. Turn knob clockwise to
increase light.

2. Inspect light bulb and replace
if necessary. (see Maintenance
section of this manual)

3. Remove screws holding back
access panel in place and
remove back access panel.
Secure end of “flame wand”
back into the support bracket.

~ 7 ~

ELECTRIC HEATER WARRANTY

LIMITED WARRANTY:

A limited warranty is extended to the original purchaser of this heater and warrants against malfunction due

to manufacturing defects for a period of (1) one year from the date of retail purchase. Please read and follow
all details noted below.

CLAIMS HANDLED AS FOLLOWS:

- DO NOT RETURN TO PLACE OF PURCHASE

- Contact our Customer Service Department at 1-800-776-9425. You must have the model number,

serial number and date of purchase.

- They will provide you with further instuctions, which may include replacement parts, repair or

replacement at our option.

CALL 1-800-776-9425 FOR SERVICE (9AM-6PM MON.-FRI.) or EMAIL US AT

[e-mail]

DUTIES OF THE OWNER:

This heating appliance must be operated in accordance with the written instructions furnished with this
heater. This warranty shall not excuse the owner from properly maintaining this heater in accordance with the
written instructions furnished with this heater. A bill of sale, cancelled check or payment record must be kept
to verify purchase date and establish warranty period. Original carton should be kept in case of warranty
return of unit.

WHAT IS NOT COVERED:

1. Damage caused by misuse or use contrary to the owners manual and safety guidelines.

2. Damage caused by a lack of normal maintenance.

3. Repair by an unauthorized person.

4. Damage caused by connection to an improper voltage.

5. Damaged caused by use outdoors.

~ 8 ~

LIMITATIONS:

This warranty does not imply or assume any responsibility for consequential damages that may result from the
use, misuse, or the lack of routine maintenance of this heating appliance. A cleaning fee and the cost of parts
may be charged for appliance failures resulting from lack of maintenance. This warranty does not cover claims,
which do not involve defective workmanship or materials. FAILURE TO PERFORM GENERAL MAINTENANCE
(INCLUDING CLEANING) WILL VOID THIS WARRANTY.

THIS LIMITED WARRANTY IS GIVEN TO THE PURCHASER IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR
IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY OF FITNESS FOR A
PARTICULAR PURPOSE. THE REMEDY PROVIDED IN THIS WARRANTY IS EXCLUSIVE AND IS GRANTED IN LIEU OF
ALL OTHER REMEDIES. IN NO EVENT WILL WORLD MARKETING OF AMERICA BE LIABLE FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES.

Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not
apply to you. Some states do not allow the exclusion or limitation of incidental or consequential damages so
the above limitation or exclusion may not apply to you.

For your record, staple your sales receipt to this manual and record the following

DATE OF PURCHASE:

PLACE OF PURCHASE:

SERIAL NUMBER:

MODEL NUMBER:

Printed in China

~ 9 ~