#5610 EQUATOR PEDESTAL
#5620 EQUATOR WALL MOUNT
#5650 EGG PEDESTAL
ceriotti
hair dryers
GET STARTED: EGG
GET STARTED: EQUATOR
#5610 PEDESTAL #6550 PEDESTAL
EQUATOR
Professional Hair Dryer
EGG
Professional Hair Dryer
HOOD
5 STAR BASE 5 STAR BASE
HOOD
PEDESTAL/STAND PEDESTAL/STAND
For best practice on installing and maintaining your Comfortel product.
Specific adjustments vary according to each model.
comfortel.com.au
owners manual
#5620 WALL MOUNTED
WALL ARM
WEIGHT WEIGHT
GENERAL SAFETY
1. Read carefully and keep these instructions in a
safe place.
2. Use this product only for its intended function and
do not use attachments not recommended by the
manufacturer.
3. Always ensure the appliance is turned o at the
power point before inserting or removing the plug.
4. Do not use outdoors.
PRECAUTIONS
1. Always follow the instructions specific to your model hair
dryer and read the data label axed to the rear of the hood
2. Before connecting hair dryer to mains power, check the
voltage and power usage indicated on the data label are
suitable for corresponding mains power supply.
3. Before mounting the hood onto the stand or wall arm,
ensure that the hair dryer is not connected to mains power
supply.
4. Never enclose or cover the top of the hair dryer hood as
air must be able to move through the hair dryer for it to
function properly.
5. Ceriotti and Comfortel decline all responsibility for any
injury to persons or damage to property caused by
installation or assembly that has not been carried out
in compliance with our recommend precautions, or
using supports and/ or accessories other than those
manufactured by Ceriotti , or for any injury to persons or
damage to property caused by installation or assembly
that has been carried out by a non-specialized or nonauthorised person.
6. In the case of the wall-mounted arm, Ceriotti and
Comfortel moreover decline all responsibility for injury to
persons or damage to property resulting from unsuitability
of any support made of masonry or any other material.
7. Before cleaning, ensure that appliance is disconnected from
power supply and that it has cooled down completely.
It can then be cleaned using a damp cloth moistened
with water or ordinary commercially available detergents,
provided they do not contain alcohol or acetone.
8. For replacement of internal parts, or in the event of damage
to the flexible power supply cord, all work must be
completed by an authorized and qualified person only.
9. Never use this appliance near water such as bath tubs,
showers, sinks or any other contained water. Never
wall mount hair dryer over bath tubs, sinks or any other
container used to hold water.
10. It is advised that the premises which provides mains
power supply to hair dryer is fitted with an RCD or safety
switch device with at least a 30mA trip sensitivity. Consult a
qualified electrician for further advice.
11. For replacement of internal parts or in case of damage to
cord or appliance, contact the manufacturer or distributor.
12. This appliance is not suitable for use by children
13. This appliance is not to be used by children or persons
which reduced physical, sensory or mental capabilities; or
by those who lack the experience and knowledge to use
the appliance unless being supervised or instructed.
14. Do not allow children to play with appliance.
15. Do not conduct cleaning or maintenance of this appliance
in the presence of children.
PARTS LIST (FIG.4)
A. TIMER
B. HEATING INDICATOR LIGHT
C. THERMOSTAT
D. CAP
E. VISOR
F. BELL
G. FORK
H. BRIM
A
H
B
C
D
E
F
G
IMPORTANT PLEASE READ THESE SAFETY INSTRUCTIONS
CAUTION:
DO NOT USE IF FLEXIBLE CORD IS DAMAGED
ANY REPAIRS TO HAIR DRYER MUST BE CONDUCTED BY A QUALIFIED ELECTRICIAN ONLY.
Water poses a serious risk even
when device is switched o, do
not leave device connected to
power supply after use.
ADJUSTMENT OF ARTICULATED
JOINT AND VISOR
ADJUSTING THE ARTICULATED JOINT
After prolonged use the articulated joint of the hood
may work itself loose resulting in the hood no longer
remaining in the set position. To tighten the joint, remove
the plug on the side of the articulated joint and tighten
the screw located inside using an appropriate Hex key (by
1/4 of a turn at a time) until the articulated joint holds the
hood in the set position.
ADJUSTING THE VISOR
After prolonged use the hinge of the visor may work itself
loose resulting in the visor no longer remaining in the set
position. To tighten the hinge of the visor, use a Phillips
head screwdriver and tighten screws on visor until the it
holds itself in the set position.
OPERATING INSTRUCTIONS
1. Plug the power cord in at the wall point and turn on.
2. SETTING THE TIME: Set the time turning the knob
(A) of the timer clockwise. When the time set has
elapsed, the knob will return to the "0" position
automatically. During operation of the hair dryer
hood, the knob can be turned to the "0" position to
turn the hair dryer o.
3. SETTING THE TEMPERATURE: Set the desired
operating temperature by turning the knob (C) of the
thermostat. The orange light (B) indicates that the hair
dryer is warming up. The light will turn o when the
set temperature has been reached.
4. Once finished using the appliance, always ensure that
the device is switched o and remove the plug from
the wall.
B
A
C
ASSEMBLY: BASE WITH STAND
1. Insert the 5 base legs (F) into the base hub (A)
2. Secure the supporting pole (B) into the base hub (A).
Insert weight (E) and then secure by tightening the
screw and washer (D) from the bottom.
3. Loosen the plastic sleeve at the top of the supporting
pole (B). Insert the smaller pedestal pole (C) so that
it rests in the sleeve without compressing the spring
within the pole (B). Fasten the small pedestal pole (C)
in place by turning the plastic sleeve clockwise.
4. Insert the articulated join of the hair dryer hood onto
the top of the pedestal pole (C) and adjust the height
as required by loosening and tightening the plastic
sleeve as described in step 3.
1. Set the bracket (A) in wall, the
recommended height is 2000mm
o the floor as pictured right.
2. Fasten plate (G) to bracket (A) using
two nuts.
3. IMPORTANT - Without removing
the safety clamp (B), that holds the
articulated part of the arm inside
which the return spring is housed,
insert the arm (C) into plate (G).
4. After loosening the two screws (D)
at the end of the arm (C), insert the
pin (E) of the fork and tighten the
two screws (D)
5. Once this has been done, the safety clamp (B) can now
be removed ensuring to hold the arm with one hand so
it does not spring open.
6. Connect the plug of the appliance into the socket on the
arm and plug other end into power outlet ensuring it is
switched o first.
7. If after use the hood tends to drop back down when it is
moved up, turn the screw (F)
HEIGHT OFF FLOOR 2000MM
ASSEMBLY: WALLMOUNT
A
F
E
D
B
C
•WARNING : Read the
instructions carefully
A
B
C
D
F
H
E
G
The information contained in this document is subject to change without notice and
should not be construed as a commitment by Comfortel Furniture Pty Ltd.
Comfortel Furniture Pty Ltd. assumes no responsibility for any errors that may appear in
this document nor does it make expressed or implied warranty of any kind with regard
to this material, including, but not limited to, the implied warranties of merchantability
and fitness for a particular purpose.
Comfortel Furniture Pty Ltd. shall not be liable for incidental or consequential damages
in connection with or arising out of the use of this document and the program material.
PRODUCT CODE
PURCHASE DATE INVOICE NUMBER
NOTE YOUR PURCHASE DATE & INVOICE NUMBER FOR FUTURE REFERENCE
Revision Date: 06.10.2016
A periodic inspection of all components and fasteners
should be made to ensure that your Comfortel
product is structurally intact and functioning properly.
Damaged and broken parts should be replaced and
loose fasteners tightened.
All maintenance to be carried out by a suitably
qualified tradesperson.
For cleaning the hood, visor and bell of the
professional hair dryer:
· Wipe using a soft, damp cloth moistened with
warm soapy water
· Dry with clean soft cloth
(never use abrasive cleaners)
Do not use:
· acetone · furniture polishes
· bleach · detergent
· abrasive cleaners · steel wool
MAINTENANCE
CLEANING
PLEASE RETAIN THIS INFORMATION FOR FUTURE REFERENCE.
For more information about our products and services, contact us at comfortel.com.au
comfortel.com.au
VOLTAGE 230240V
POWER 1000W 50HZ
#5610 EQUATOR PEDESTAL HAIR DRYER
#5620 EQUATOR WALL MOUNTED HAIR DRYER
#5650 EGG PEDESTAL HAIR DRYER
PERIOD AND DESCRIPTION PRODUCTS
12 MONTHS PARTS & LABOR All products
2 YEARS PARTS ONLY All products excluding small electrical appliances
3 YEARS PARTS ONLY All electric actuators
5 YEARS PARTS ONLY Taps cartridge, ceramic basins
10 YEARS PARTS ONLY Gas-lifts and gas-lift swivel plates
TERMS AND CONDITIONS
For more information about our warranty, please contact us at comfortel.com.au.
WARRANTY PERIOD
©Comfortel Furniture 1997-2017. All rights are reserved.
No part of this document may be photocopied,
reproduced or translated to another language without
written consent of Comfortel Furniture Pty Ltd.
Loading...