Comfort Company 77103 User Manual
Toll Free 800.564.9248
www.comfortcompany.com
509 South 22nd Ave Bozeman, MT 59718
HALO SAFETY RING
MODEL: 77103 - CARROLL BED MOUNT
FEATURES AND BENEFITS
• Circular design with vertical mounting bar prevent
entrapment and allow for exit points for the neck,
head, and chest.
• Meets or exceeds FDA and Hospital Bed Safety
Workgroup (HBSW) alternative dimensional and
assessment guidelines established March 10, 2006.
• Locking mechanism allows for rotation to assist
resident exiting bed.
• Promotes bed mobility which can help to prevent
skin breakdown.
• Easy removal for bed side transfers and bed therapy.
• Prevents Zone 1-4 entrapment.
• 1000 lb. weight capacity.
• Easy to install.
• Lifetime Warranty.
- WARNING -
• Serious injury or death can result if the Halo Safety Ring is not properly installed.
• DO NOT use this product or any available optional equipment without rst completely reading & understanding these instructions. If you are unable to understand the warnings, cautions or instructions, contact
customer service at (800) 564-9248 for assistance before attempting to use this equipment - otherwise,
injury or damage may occur.
• The Halo Safety Ring is not intended to prevent an individual from inadvertently rolling out of bed. DO
NOT use the Halo Safety Ring for restraint purposes. DO NOT use to transport or move bed.
• ENTRAPMENT MAY OCCUR. Proper patient assessment and monitoring, and proper maintenance and
use of equipment is required to reduce the risk of entrapment. Variations in mattress thickness, size or density could increase the risk of entrapment. Visit the FDA website at http://www.fda.gov to learn about the
risks of entrapment.
• Remove bed rails and all bed rail mounting brackets prior to installation of the Halo Safety Ring.
• The Halo Safety Ring is rated for use with patients weighing up to 1000 lbs. Although the Halo Safety
Ring is rated for such use, it may become deformed or broken if excessive force is exerted on the device.
• After installation, verify the mattress is in rm contact with the Halo Safety Ring and that the mattress cannot shift away.
FIGURE 1
• Detent pins used to rotate the Halo Safety Ring must be engaged with
holes in the Halo Bracket prior to use, refer to Figure 1.
• The Halo Safety Ring must be perpendicular (90 degrees) to the bed if
DETENT PINS ENGAGED
WITH HALO SAFETY
RING BRACKET
used to assist the user out of a chair. Detent pins must be engaged with
the holes in the Halo Safety Ring bracket prior to use as a patient assist.
IMPROPER INSTALLATION CREATES A RISK OF ENTRAPMENT
IN ORDER TO AVOID ENTRAPMENT, THE MATTRESS MUST REMAIN IN FIRM CONTACT
WITH THE HALO SAFETY RING ON BOTH SIDES OF THE BED. IF A HALO SAFETY RING IS
ONLY INSTALLED ON ONE SIDE OF THE BED, THE MATTRESS MUST ALSO REMAIN IN
FIRM CONTACT WITH THE MATTRESS STAY/BRACKET ON THE OTHER SIDE OF THE BED.
!WARNING!
77103HALO_LIT034_0820121 OF 3
Toll Free 800.564.9248
3“
www.comfortcompany.com
509 South 22nd Ave Bozeman, MT 59718
HALO SAFETY RING
TOOLS NEEDED FOR ASSEMBLY
½” Closed End Wrench
½” Socket with Ratchet Wrench Extension
ITEMS INCLUDED IN THIS BOX
77104
ITEMS IN THE HARDWARE KIT ITEM #77108
77107
Tube Length
1- Halo Safety Ring
Item No. 77104
2- Carroll Mount Brackets
Item No. 77107
2- Halo Safety Ring Hardware
Kits - Kit parts listed below
Item No. 77108
2- 3” Zinc Bolts
2- Zinc Nut
4- Zinc Washers
2- Zinc Lock Washers
MODEL: 77103 - CARROLL BED MOUNT
INSTALLATION STEPS:
Remove all bed rails
1
and all bed rail mounting brackets prior to
installation.
Duplicate step 2 on the
3
opposite side of the
bed.
Your Halo Safety Ring is now installed
and ready for resident use!
2
4
Using the original bed
frame holes from the
Carroll Side Rail, install the Carroll Mount
(77107) using the enclosed hardware (77108).
Tighten securely to bed
frame. (See Figure 2)
Slide the Halo Safety Ring (77104) into
the Carroll mounting
bracket on the preferred side by pinching
the detent pins on the
bottom bar of the Halo
Safety Ring. Once inserted, the detent pins
will pop out securing
the Halo Safety Ring in
position.
Bolts
Mattress must remain in rm contact with the Halo Safety
Ring on both sides of the bed. If a Halo Safety Ring is only
installed on one side of the bed, the mattress must remain in
rm contact with the mattress stay or mount bracket on the
other side of the bed.
In order to prevent entrapment in Zones 1 through 4 and
create a protective sleep environment, two complete Carroll
Circle Mounting Brackets must be installed on the same bed.
*The Halo Safety Ring is designed to accommodate a range of different bed manufacturers. If the device does not easily attach to the bed deck, interferes
with the sub-frame, or the mattress does not rmly contact the Halo Safety Ring bracket – DO NOT USE. Contact customer service at (800) 564 - 9248
Washers
Lock
Washers
- WARNING -
Nuts
FIGURE 2
77103HALO_LIT034_0820122 OF 3
Loading...