Comeup H-2500 Instruction Manual

CABLE PULLER

Model:

PN:487265 220V/50Hz、486122 230V/50Hz、489635 110V/50Hz

483636 240V/50Hz、483958 240V/50Hz、482316 220V/60Hz

486280 230V/50Hz、487655 110V/50Hz、487705 110V/60Hz、487281 110V/50Hz

Introduction

 Feature

Drum type Large Drum Small Drum
Pulling capacity kg 1,500 2,500

Rope speed m / min
Gear train hypoid gear plus spur gears

Gear ratio 154:1
Motor rating IP44 , kw x p 0.6 x 4

Drum dimension mm

Percentage Duty Cycle 25% ED

 Unpacking

．Rope arm
．Base plate,except for PN:489635
．Wire rope 8 mm x 50 m, except for PN:489635 483958
．Detachable rope storage roller
．Foot control kit with 2.0 mm
．Power lead 1.5 mm
．Power lead 2.0 mm

50 Hz 4.0 2.5
60 Hz 5.0 3.0

width 124 104
drum dia. 130 74
flange dia. 166 94

2

x 3C x 2 m lead

2

x 3C x 3 m and plug

2

x 3C x 3 m and plug for PN:487705

H-2500

1pc
1pc
1pc
1pc
1pc
1pc
1pc

Installation

1. Install this machine on the ground horizontally.

2. Confirm that the machine voltage complies with the power source.

3. Connect the power cord with the power source, set the over – load
protection switch in to the “RESET” position.

4. Press the “Foot Control” down, the drum rotates in a clockwise direction and
make sure there is no noisy sound level or malfunction.

5. Release the “Foot Control” to have an emergency stop. The brake performs
inter – locked and motor has instantly hold the load while power failure.

 Wiring Diagram

 Read this manual carefully

You should carefully read and understand this manual before operating it.
Careless winch operation may result in personal injury hazards or property
damage.

 Information requesting or parts ordering

Please specify the followings information:

．Winch PN ．Serial number
．Part description ．Replacement part number
．Quantity for each part

Warning

．The cable puller is not intended to be used in any manne r for the movement or

lifting of personnel

．The rated capacity shown is based on the first layer of rope on the drum

．

The rope winding on the drum shall remain 5 wraps from the drum

Parts List

Ref No. Description Part Number Qty

1 Drum A kit

Motor kit, 110V/220V, 60Hz

2

3 2nd shaft
4 1st gear
5 3rd shaft
6 2nd gear
7 4th gear
8 Output shaft

9 4th shaft
10 3rd gear
11 Gearbox cover kit
12 Drum B kit
13 Base plate kit
14 Sheave guider kit
15 Divertor kit
16 Drum bracket
17 Foot pad
18 Rope wheel kit
19 Pulley block
20 Fix shaft
21 Wing nut kit
22 Wire rope

23

24 Foot control kit

25

Motor kit, 110V/220V/230V, 50Hz
Motor kit, 120V/240V, 50Hz
Motor kit, 110V/220V, 60Hz

Terminal box kit, 110V, 50Hz
Terminal box kit, 220V/230V, 50/60Hz
Terminal box kit, 240V, 50Hz

Power lead, 3 flat pins plug
Power lead, 3 round pins plug
Power lead, 3 flat pins plug

(PN:486280、487281)
Power lead, 2 flat pins plug (PN:487705)

880873
880896
880897
880898
883099
880874
880875
880876
880877
880878
880879
880880
880881
880882
880883
880884
880885
880886
880887
880888
880889
880890
880891
880892
880893
880899
880901
880902
880894
880904
880905

882852
883098

Winch Assembly

1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1

1
1