COMEUP Compact Winch User Manual

Compact Winch

Limited One (1) Year Warranty Statement

Comeup Industries Inc. ( ) warrants to the original purchaser that the mechanical compnents

and electrical components of the Compact Winch will be free of defects in material and

workmanship for one (1) year. All mounting kits and other accessories carry one (1) year

limited warranty against defects in material workmanship.

This Warranty applies only to the original purchaser of the winch. To obtain any warranty service, the

Purchaser under this Limited Warranty is requested to report or his authorized distributors

of any claims. The Purchaser must provide a copy of the proof of purchase bearing the winch serial

number, date of purchase, owners name email, or Tel & Fax, address and registration number. Any

product determines to be defective will be repaired or replaced at sole discretion

without charge to Buyer upon Buyer’s compliance with these procedures. Seller or its Authorized

Distributors may make reasonable charges for parts and labour for repairs not covered by this Limited

Warranty.

takes the responsibility for all parts and components to be free from defects in materials and

workmanship, but the following are hereby excluded and disclaimed:

(1). All warranties of wire rope assemblies after initial use.

(2). All warranties of fitness for a particular purpose.

(3). All warranties of the product’s finish

(4). All warranties of merchantability

The Limited Warranty does not cover any failure that results from improper installation, operation or

the Purchaser’s modification in design. reserves the right to change Product design without

notice. In situations in which has changed a product design, shall have no

obligation to upgrade or otherwise modify previously manufactured products.

1

Compact Winch

Thank you for purchasing a Winch. This manual covers operation and maintenance of

the winch. All information in this publication is based on the latest production information available at

the time of printing.

General Safety Precautions

The winch has been designed to give safe and dependable service if operated according to the

instructions. Please read and understand this manual before installation and operation of the winch.

Follow these general safety precautions:

Confirm that the winch complies with the using conditions.
Keep the winch secure strongly and the rope is not wound to be deviated to the drum.
Don't use unsuitable pulleys or accessories concerned.
Don't use unsuitable rope in construction, strength or having any defects.
Pay attention to the grounding, it provides a path of least resistance for electric current to reduce
the risk of shock.
Check the winch for smooth operation without load before loading operation.
Make sure the wire rope to be wound evenly in the first layer on the drum, rewind it if a mixed
windings in existence.
If a wire rope is found an uneven winding or accumulated at one side of the drum, align it adequately.

WARNING

！

1. The winch is not to be used to lift, support or otherwise transport personnel.

2. A minimum of five (5) wraps of rope around the drum is necessary to support the load rated.

3. The owner and/or the operator shall have an understanding of these operating instructions and the
warning before operating the electrical winch. Failure to follow these warnings may result in loss of
load, damage to the winch, property damage, personal, or fatal injury.

4. The owner shall retain this manual for further reference to important warnings, installation, operating
and maintenance instructions.

2

I . Installation Precaution

General Safety Precaution

The following environmental conditions may result in the possible causes of hoist trouble.

！

DANGER

● Low temperature below -10℃ ,high
temperature above 40℃ or humidity

above 90% conditions

※Cause malfunction of spare parts ※Cause explosion

● In heavy acid or salty conditions

● In rain or snow conditions

● In an organic chemistry or explosive

powder conditions

● In a heavy general powder conditions

※Cause malfunction of spare parts
※Cause rust or short circuit

※Cause malfunction of performances

3

I I . Handing Precautions

＊ To prevent the risk of electric shock, the power plug must be plugged into a matching outlet and
grounded in good condition.

＊ Never try to lift a load higher than the rated cap.
＊ Never hitch a ride on the hook, sling or load being moving.
＊ Winches are not to be used for lifting or lowering people.
＊ Don’t work, walk or stand under an operating winch.
＊ Always remain in control. Never neglect the winch while actually hosting a load.
＊ While working, never stand under a lifting load or within the conveying area.
＊ Always look up when working around winch, there is potential danger overhead.
＊ Never gravitate a load free.
＊ Be sure to lift a load vertically. Slack may allow wires to be caught in the drum.
＊ A minimum of five (5) wraps of rope around the drum is carry out the daily checking necessary to

support the load rated.
＊ Prior to starting of use, carry out the daily checking without fail, and after confirming the safety of
function.

＊ If having a counter rotation incurred, make sure to correct its rotation direction.
＊ Prior to lift. Make sure to have a precise performance of brake. If any malfunction of brake happened,

stop the operation immediately.

＊ When load suspended in air, it will not allow to be welding.
＊ Wire rope with one or more of the following defects shall be removed or replaced immediately.

1) kink, 2) distortion, 3) corrosion.

4) showing sings of excessive wear or of having broken wires not less than 10 pcs.

＊ Stop the operation if there is any queer noise or vibration in the gear box to be happened.
＊ Do not connect the wire rope with the grounding of welding machine.
＊ While welding, do not have any contact with the welding objects because of having spark.
＊ Do not pull the switch.
＊ Never plugging (instant reverse-wind) or inching.
＊ Do not over continuous ratings.
＊ In order to prevent the layer down due to over loosening of rope irregular winding, etc., operate

according to the suitable operating method.

＊ Use a winch by fixing so securely that the rope around the drum is uneven.
＊ Be sure to fix a rope in the center of swivel hook.
＊ Be sure to stop operation immediately when the wire rope becomes fully slackened.
＊ Avoid catching the hook or lifting a load on a fixed obstruction.
＊ Always leave the pendant switch positioned immediately after use.
＊ Make sure that the load being lifting is well balanced and secured before starting.
＊ Avoid water splashes on the pendant switch.
＊ Never wrap the load with the wire rope.

4