Comeup 881490 Users Manual

W

ireless Remote Module

Wireless Receiver Model NO：881490

For DS-9.5rs

DS-9.5rsi

Accessories:

1. Wireless Transmitter: 881102.

2. Lithium Battery: 3V CR2032.

12V: 293655
24V: 293160

12V: 293244
24V: 293266

A

Receiver PN：881490
built in control box

DS-9.5rsi

1.

3. Handsaver Strap.

I.Specifications

1. Transmission range: 15 ~ 27 m (50 ~ 90 ft)

2. Receiver operation voltage: 8 ~ 24 V

3. Protection: IP 66

4. Operating temperature range: -20°C ~ +70°C

III Operation

1. Install and replace battery.

a. Remove the three screws from the wireless transmitter.
b. Separate the top section and remove the old battery and dispose it.
c. Insert new battery and join the top section with the bottom section.
d. Make sure to fasten the three screws.

2.

B

Receiver PN：881489
built in control box

DS-9.5rs

3.

2. Start
A. For DS-9.5rsi winch

a. Attach the red(+) and black(-) battery leads to battery set on the vehicle, then the

buzzer alarms and the right LED on the bridge control box blinks blue for decoding.

b. Hold the Power Button of the transmitter for about 5 seconds，then the LED Indicator

lights permanently.

c. Hold either Cable In Button or Cable Out Button of the transmitter, then the buzzer

alarms long sound lasting for 5 seconds.

d. The right blinking blue LED of the bridge control box turns off, but the left lights green

permanently.

e. The wireless remote control is now workable.

1

Power Button

Cable IN

LED Indicator

Cable OUT

Lithium Battery: CR2032 (3V)

Left LED

Right LED

DS-9.5rsi

p

B. For DS-9.5rs winch

a. Attach the red(+) and black(-) battery leads to battery set on the vehicle, then the

buzzer alarms.

b. Hold the Power Button of the transmitter for about 5 seconds, then the LED Indicator

lights permanently.

c. Hold either Cable In Button or Cable Out Button of the transmitter, then the buzzer

alarms long sound lasting for 5 seconds.

d. The wireless remote control is now workable.

LED Indicator

3. Stop

a. Hold the Power Button of the Transmitter for 5 seconds for stopping the function.
b. Any silence of operation for 5 minutes, the wireless remote module turns off

4. Reset

a. Disassembly the battery leads from the battery set and attach the leads to the battery
b. Hold the Power Button of the transmitter for about 5 seconds, then the LED Indicator
c. Hold either Cable In Button or Cable Out Button of the transmitter for the process of the
d. After the completion of the decoding, the buzzer alarms long sound lasting for 5

e. Ascertain the process of the decoding shall be completed within 5 minutes, if it fails to

5. Notes
a. The wireless remote control and remote control can be exchanged for activating the

b. Blinking Green LED light shows batter low, the battery should be replaced immediately.
c. The remote control can be workable on independence.。

d. If the motor is overheating, the left LED of DS-9.5rsi lights red and buzzer has 2 short
e. Please note only one remote can be reset for each receiver.

f. Blinking Red LED for poor signal.

Cable OUT

Power Button

Cable IN

DS-9.5rs

automatically.

set again, then the right LED blinks blue and buzzers lasting in 5 minutes for decoding.
lights permanently
decoding.
seconds and the right LED turns off compared to the permanent green light on the left

LED.
finish, it is inevitable to restore the original setting at the manufacturer.

winch, but it takes about 10 seconds for exchanging。

beeps every 5 seconds until the temperature of the motor falls within the safety range.

FCC and Industry Canada (IC) Warning:

• This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired o

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/ TV technician for help.
CAUTION:

Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the
equipment.

eration.

2