Comdial C0408, C0816, C1632 User Guide

l

Press desired storage location button on
Console. Listen for fast tone bursts.

0 Select specific line, line group, or no selec-

tion as required.

l

Press specific telephone line button for
line.

-or-

0 Press 1 - 4 on the telephone dial pad for

line group.

-or-

. Press 0 on the telephone dial cad for no

selection. (When 0 is stored and automatic
dialing is used, system will pick line as­signed to telephone or last line used.)

l

Dial the number sequence to be stored from

the telephone dial pad (up to 16 digits).

l

To store a pause, press HOLD on
telephone.

l

To store a flash, press TAP on telephone.

I

FREQUENTLY

CALLED NUMBERS

DIGITECH

To store another number for automatic dial-

W,

l

Press TRANSICONF on telephone.

l

Press next Console button.

o Select line, group or none as described

above.
0 Dial number sequence as described above.
. Repeat procedure for each desired button.

HINT: Store often-used, host system PBX or

CENTREX feature access codes at Console but-

ton locations. This willprovide one-button access

to those host system features.

To end programming,

. Press MNTR (SPKR) on telephone.

DIALING NUMBERS

To dial numbers automatically,

. Press desired Console button.

-or-

0 If desired button also provides DSS/BLF

operation,

l

Press HOLD on telephone and then press

desired button on Console.

l

When party answers, lift handset of
telephone.

COMDIAL

Charlottesville, VA 22906-7266

Printed in U.S.A.

-m 4’g1

32-Button DSS/BLF

Console

User’s Guide

DigiTech system models:

GCA70-187.02

OVERVIEW

The 32-Button DSS/BLF Console extends the

memory button capability of an adjacent com­panion DigiTech telephone by an additional 32

buttons and status lights. The buttons can be
programmed for automatic dialing (autodial)
and/or direct station selection (DSS) with busy
lamp field (BLF).

BLF

STATUS

LIGHTS h

REFERENCE 1

CARD 1

/

L OS BUTTON FOR

STATION PORT 10 PORT 41

When a DSSiBLF console is initially connected at
a station port, the system recognizes it as such,
and automatically assigns the station intercom
numbers to the console buttons for the maximum

numberof stations connected to the system. (The
maximum coverage is limited by the 32 available
buttons.)

OS BUTTONS -

-

- ass BUT-I

‘ON

FOR STATION

DSS/BLF OPERATION

DSS/BLF provides one-button intercom calling

with visual indication of station status.

STORING DSS NUMBERS

To program DSS numbers,

Press ITCM on telephone. Listen for tone.
Dial +@ t 3 from telephone dial pad. Tone

will stop.

Press desired button on Console.

Dial extension number from telephone dial
pad.

Repeat previous two steps for all desired
stations.

Press MNTR (SPKR) on telephone when
programming is complete.

Record DSS names or locations on supplied
reference card and install card on Console

faceplate.

. Lii out plastic reference card cover from

Console faceplate.

l

Write or type names in squares on refer­ence card.

l

Install card under cover and snap cover

back into place on Console.

To blank a DSS button,

l

Press ITCM on telephone

l

Dial t t 3 from telephone dial pad.

l

Press desired console button.
Press MNTR (SPKR) on telephone.

l

DSS CALLING

To voice announce a call to a DSS number,

l

Lift telephone handset.

l

Press DSS button on Console.

l

Voice announce.

NOTE: If you are transferring an outside call to an
intercom station, press the TRANS/CONF button

on the telephone before pressing the DSS button

on your Console.
To tone signal a call to a DSS number,

l

Lift telephone handset.

.

Press DSS button on Console.

.

Press ITCM on telephone. When station
answers, two-way conversation can take
place.

The

BLF lights that are adjacent to the DSS
buttons on the Console indicate the status of the
stations programmed at the buttons. Status con­ditions are as follows:

BLF STATUS STATION STATUS
Light Off Station Idle.
Light Flashing Station calling you on

intercom line.
Station ringing if

monitoring feature is
active.

I

I

Light On Steady I 1 Station busy.

I.

Station in do not dis-

turb mode.

Light Flutters Station has left call-

back message.

NOTE: An autodial number also can be
programmed as a secondary function at every

DSSIBLF memory location. See Automatic Dial­ing instructions for details.

AUTOMATIC DIALING

Automatic dialing provides one- or two-button
calling of often used numbers and access codes

as a secondary function of the DSS buttons. For
a primary autodial function, blank the DSS/BLF

function at the desired buttons.

STORING NUMBERS

To store a number for automatic dialing,

l

Press ITCM on telephone. Listen for tone.

l

Dial t t 1 from the telephone dial pad. Tone

will stop.

1

I

GCA 70-l 87