Page 1
0 Select specific line, line group, or no selection
as required.
0 Press specific telephone line key for line.
-or-
o Press 1 - 4 on the telephone dial pad for line
group.
-or-
= Press 0 on the telephone dial pad for no
selection. (When 0 is stored and automatic
dialing is used, system will pick line assigned to telephone or last line used.)
l
Dial the number sequence to be stored from
the telephone dial pad. (up to 16 digits).
l
To store a pause, press HOLD on
telephone.
l
To store a flash, press RECALL on
telephone.
COMDIAL
Committed to U.S.
in business communications.
Executech
32-Button Adjunct
design leadership
To store another number for automatic dialing,
l
Press SAVE on telephone.
l
Press next Module key (or press HOLD plus
Module key if DSS/BLF is programmed).
l
Select line, group or none as described
above.
l
Dial number sequence as described above.
l
Repeat this procedure for each desired key.
HINT:
CENTREX feature access codes at Module key
locations. This will provide one-key access to
those host system features.
To end programming,
To dial numbers automatically,
Store often-used, host system PBX or
l
Press MONITOR on telephone.
l
Press desired Module key.
-or-
. If desired key is also programmed for
DSS/BLF operation,
l
Press HOLD on telephone and then press
desired key on Module.
l
When party answers, lift handset of
telephone.
COMDIAL
Charlottesville, VA 22906
I-
--4a-lz13G-oSL7
GCA 70-097.01
June, 1988
Feature Module
User’s Guide
For use with following
hybrid/key system models:
l
1432 Series
l
22xx
Series
Page 2
OVERVIEW
The 32-Button Adjunct Feature Module extends
the memory keys of your Executech II multiline
telephone by an additional thirty-two keys and
status lights. The keys can be programmed for
automatic dialing and/or direct station selection
(DSS) with busy lamp field (BLF).
DSS
K&i
7
DIRECT STATION SELECTION BUSY
LAMP FIELD (DSS/BLF) OPERATION
DSS/BLF provides one-key intercom calling with
visual indication of station status.
To program DSS numbers,
Press ITCM on telephone. Listen for tone.
Dial 85 from telephone dial pad. Tone will
stop.
Press desired key on Module.
Dial extension number from telephone dial
pad.
Repeat previous two steps for all desired sta-
tions.
Press MONITOR on telephone when
programming is complete.
Record DSS names or locations on supplied
reference card and install card on Module
faceplate.
l
Lift out plastic reference card cover from
Module faceplate.
l
Write or type names in squares on
reference card.
l
Install card under cover and snap cover
back into place on Module.
NOTE:
programmed as a secondary function at every
DSS/BLF memory location. See Automatic Dialing instructions for details.
An autodial number also can be
.
Press key on Module.
.
Press ITCM on telephone. When station
answers, two-way conversation can take
place.
The BLF lights that are adjacent to the DSS
keys on the Module indicate the status of the stations programmed at the keys. Status conditions are as follows:
BLF STATUS STATION. STATUS
Light Off Station Idle
Light Flashing Station calling you on
intercom line.
Light On Steady Station busy.
Station in do not dis-
turb mode.
Light Flutters Station has left call-
back message.
AUTOMATIC DIALING
Auto dialing provides one-key calling of often
used numbers and access codes.
To store a number for automatic dialing,
To voice announce a call to a DSS number,
l
Lift telephone handset.
l
Press key on Module.
. Voice announce.
NOTE:
If you are transferring a call, the outside
line is automatically placed on hold when a DSS
key is pressed.
To tone signal a call to a DSS number,
0 Lift telephone handset.
Press ITCM on telephone.
Listen for tone.
Press SAVE on telephone. Tone will stop.
Press desired key on Module. Listen for fast
tone bursts.
-orIf desired key is also programmed for
DSS/BLF operation (as described pre-
viously),
l
Press HOLD on telephone and then press
desired Module key.
Listen for fast tone bursts.
Loading...