Comdial 1432, 22xx User Guide

l

Press specific telephone lineckey for line.

-or­e Press 1 m 4 on the telephone dial pad for line

group.

-or­e Press 0 on the telephone dial pad for no

selection. (When 0 is stored and automatic
dialing is used, system will pick line as­signed to telephone or last line used.)

. Dial the number sequence to be stored from

the telephone dial pad (up to 16 digits).

l

To store a pause, press
telephone.

. To store a flash, press

telephone.

HOLD

RECALL

on

on

To store another number for automatic
dialing,

l

Press

SAVE

on telephone.

. Press next Module key (or press

Module key if DSS/BLF is programmed).

l

Select line, group or none as described

above.
e Dial number sequence as described above.
. Repeat this procedure for each desired key.

HOLD

plus

OFF-HOOK VOICE ANNOUNCE

AND HANDSFREE ANSWER-

BACK

The Adjunct Feature Module can receive a voice
signalled intercom call (voice announce) at the
same time that the paired station is active on

another call. You can answer the voice sig­nalled intercom call in a handsfree manner

without interrupting your currently active call.

To answer voice announce in a

handsfree manner,

. Hear voice signalling (voice announce) over

Module speaker,

l

Respond to voice announce by speaking

toward Module (handsfree answerback).

Adjust the audio level of the voice signalling with

the speaker volume control located on the right

side of the Module.

COMDIAL

Made rJ&t in the USA

Executech

32-Button Adjunct

Feature Module

(With Voice Announce Capability)

USER GUIDE

HINT:

CENTREX feature access codes at Module key
locations. This will provide one-key access to
those host system features.

Store often-used, host system PBX or

To end programming,

l

Press

MONITOR

on telephone.

To dial numbers automatically,

0 Press desired Module key.

-or-

. If desired key is also programmed for

DSS/BLF operation,

e

Press

HOLD

desired key on Module.

. When party answers, lift handset of

telephone.

on telephone and then press

COMDWL

Charlottesville, VA 22906

II

~@w&i0~.

GCA 70-096.01

June 1988

For use with following hybrid/key system models:

l

1432 Series

0 22xx

Series

OVERVIEW

The 32Button Adjunct Feature Module extends
the memory keys of your Executech II multiline
telephone by an additional thirty-two keys and

status lights. The keys can be programmed for

automatic dialing and/or direct station selection

(DSS) with busy lamp field (BLF).
This Module also provides an off-hook voice an-

nounce and handsfree answerback features.

With this capability, a second call can be an-

nounced to you while you are engaged on a call.
You can respond to the announcement, if neces­sary, in a handsfree manner.

AuM DIAL &
DSS KEYS

7

DIRECT STATION SELECTION

BUSY LAMP FIELD (DSS/BLF)

OPERATION

DSS/BLF provides one-key intercom calling with

visual indication of station status.

To program DSS numbers,

l

Press ITCM on telephone. Listen for tone.

l

Dial 85 from telephone dial pad. Tone will
stop.

l

Press desired key on Module.

l

Dial extension number from telephone dial
pad.

l

Repeat previous two steps for all desired sta-

tions.

l

Press MONITOR on telephone when

programming is complete.

. Record DSS names or locations on supplied

reference card and install card on Module

faceplate.

l

Lift out plastic reference card cover from
Module faceplate.

0 Write or type names in squares on

reference card.

0 Install card under cover and snap cover

back into place on Module.

NOTE:

programmed as a secondary function at every

DSSBLF memory location.

ing instructions for details.

l%;$e announce a call to a DSS

l

l

l

NOTE:

line is automatically placed on hold when a DSS
key is pressed.

To tone signal a call to a DSS number,

0 Lift telephone handset.

An autodial number also can be

See Automatic Dial-

,

Lift telephone handset.
Press key on Module.

Voice announce.

If you are transferring a call, the outside

0 Press key on Module.
. Press ITCM on telephone. When station

answers, two-way conversation can take
place.

The BLF lights that are adjacent to the DSS
keys on the Module indicate the status of the sta­tions programmed at the keys. Status condi­tions are as follows:

BLF STATUS STATION STATUS

Light Off
Light Flashing

Light On Steady Station busy.

Light Flutters Station has left call-

Station Idle

Station calling you on
intercom line.

Station in do not dis­turb mode.

back message.

AUTOMATIC DIALING

Auto dialing provides one-key calling of often
used numbers and access codes.

To store a number for automatic
dialing,

l

Press ITCM on telephone. Listen for tone.

l

Press SAVE on telephone. Tone will stop.

. Press desired key on Module. Listen for fast

tone bursts.

-or-

. If desired key is also programmed for

DSS/BLF operation (as described pre-

viously),

l

Press HOLD on telephone and then press

desired Module key.

l

Listen for fast tone bursts.

l

Select specific line, line group, or no selection
as required.