Page 1
Enjoy your
XFINITY® TV
right away!
Program your remote to
get started.
XFINITY XR11
Remote Control
USER’S GUIDE
It’s simple to program your XFINITY Remote to control your
TV and Audio Video Receiver.
Your XFINITY Remote is already programmed to
control your set-top box. To program the remote
for control of Power, Volume, Mute and TV
Input on your TV or Power, Volume, and Mute
on your audio video receiver (AVR), including a
soundbar, follow the steps below.
Note:
A soundbar is a type of AVR.
Here’s how to program your
remote for control of a TV or TV
and AVR:
1. Remove the battery pull tab from the remote
control battery compartment and make sure
your TV, AVR and set-top box are powered
on.
2. Refer to the “Setup Codes for TVs” and “Setup Codes for AVRs” sections on the back of
this guide to nd the manufacturers of your
TV and AVR.
3. Press and hold the Setup button on your
remote until the status LED changes from red
to green.
4. Enter the rst code listed for the TV manufacturer. The status LED should ash green
twice when the code is entered.
5. Press the TV Power button on the remote.
If the TV turns off, you have successfully
programmed your remote. Turn the TV back
on and press the VOL +/- and Mute buttons
to conrm they control the volume of your
device.
6. If the TV (or AVR) does not turn off or the
VOL +/- and Mute buttons do not work,
repeat the steps above using the next code
listed for your TV manufacturer.
CAN’T FIND YOUR CODE?
If you can’t program your remote for TV and/
or AVR control using the codes on the back of
this guide, follow the steps below to search for
your code.
1. Turn on your TV and AVR.
2. Press and hold the Setup button on your
remote until the status LED changes from red
to green.
3. To search for a TV code, enter 9-9-1 on the
remote. To search for an AVR code, enter
9-9-2. The status LED should ash green
twice.
4. Press the CH ^ button repeatedly to search
through the manufacturer codes until the
device you are programming turns off.
5. After the device turns off, press Setup. The
status LED on your remote should ash
green twice. Press the TV Power button on
the remote. If the device turns on, your have
successfully programmed your remote.
xfinity.com/remotes
Troubleshooting
GENERAL
TROUBLESHOOTING
:Q Why does the status LED ash red then
green while I am entering the code on my
remote?
:A You may have entered an incorrect code.
Check the code and try re-entering it.
:Q Why does the status LED ash red, but
there is no response when I press a key?
:A Make sure the remote is aimed at your TV
or AVR and is no farther than 15 feet away.
Also, make sure your set-top box is powered
on and in plain sight.
TV Power: Turns your TV on/off.
All Power: One button to turn the TV,
AVR and set-top box on/off.
Vol +/–: Turns the volume up and down
on the set-top box. After your remote is
programmed for TV and/or AVR control,
these keys control the TV or AVR’s
volume.
CH ^/∨: Selects the next higher or next
lower channel.
Mute: Turns the sound on and off.
Replay: Jumps back 15 seconds.
Note: Some features above require
programming the remote for control of a
TV and/or AVR.
Video Controls: Controls On Demand
or DVR viewing, Play/Pause, Fast-For-
ward, and Rewind.
Exit: Exits guide screens and returns you
to TV viewing.
Search: Search for content by channel,
program or key words.
Rec: Records content currently being
viewed.
XFINITY/Menu: Enters the XFINITY
menu for access to the guide, Saved
programs, On Demand and Apps.
Guide: Shortcut to TV listings.
OK: Selects the highlighted item within
the guide.
Last: When viewing content, enters the
Recent menu to select from the 9 most
recently viewed programs or, when in
the XFINITY menu, returns you to previous guide screen.
Info: Provides a program description.
A, B, C, D: Context-sensitive control
keys.
Keypad (0-9): Alphanumeric keys to
select content by channel number or
keywords.
Setup: Used for programming your
remote to control your TV, AVR, and
set-top box.
TV Input: Changes to the next available
input on your TV.
Note: Some features above require
programming your remote for control of
your TV.
Power: Enciende/apaga tu televisor.
All Power: Un sólo botón para encender/
apagar tu televisor y tu caja decodificadora.
Vol +/–: Sube y baja el volumen de tu caja
decodicadora.
CH ^/∨: Selecciona el siguiente canal
hacia arriba o hacia abajo.
Mute: Enciende y apaga el sonido.
Replay:
Nota:
Video Controls: Controlan la visual-
ización de On Demand o DVR, Play
(reproducir)/Pause (pausa), Fast-For-
ward (avanzar rápidamente), y Rewind
(retroceder rápidamente).
Exit: Te saca de las pantallas de la guía y
te regresa a ver la televisión.
Search:
Rec: Graba el contenido que se está
viendo en ese momento.
Nota: Algunas funciones mencionadas
anteriormente requieren de una caja
decodicadora de DVR o acceso a la
programación On Demand.
XFINITY/Menu: Ingresa a los menús de
la guía en pantalla
Guide: Atajo a los listados de televisión.
OK: Selecciona el artículo resaltado
dentro de la guía.
Last: Te regresa al canal o a la pantalla de
la guía anterior.
Info: Proporciona la descripción de un
programa.
A, B, C, D: Teclas de control que funcionan de acuerdo al contexto y que se
utilizan en conguraciones avanzadas.
Nota: Algunas de las funciones arriba
mencionadas requieren de una guía de
programación no disponible con todos los
aparatos.
Teclado numérico (0-9): Selecciona el
canal que deseas ver (ej., 0-9 ó 0-2-6).
Setup: Programa tu control remoto
para que funcione con tu televisor, caja
decodicadora o DTA.
TV Input:
Nota:
Here’s what your remote can do.
Esto es lo que tu control remoto puede hacer.
¡Disfruta de
XFINITY® TV
ahora mismo!
Programa tu control
remoto para comenzar.
XFINITY XR11
GUÍA DEL USUARIO
para el control remoto
xfinity.com/remotes
If you only want to program your remote for TV
control, you’re all set!
Continue with the following steps to program
your remote for AVR control.
Note:
To program your remote for simultaneous
control of both a TV and AVR, the TV must be
programmed before the AVR.
7. Press and hold the Setup button on your
remote until the status LED changes from red
to green.
8. Enter the rst code listed for the AVR manu-
facturer. The status LED should ash green
twice when the code is entered.
9. Press the All Power button on the remote.
If the AVR turns off, you have successfully
programmed your remote. Turn the AVR back
on and press the VOL +/- and Mute buttons
to conrm they control the volume of your
device. If so, you’re all set!
10. If the AVR does not turn off or the VOL +/-
and Mute buttons do not work, repeat the
steps above using the next code listed for
your AVR manufacturer.
Here’s how to program your
remote for only AVR control:
1. Remove the battery pull tab from the remote
control battery compartment and make sure
your AVR and set-top box are powered on.
2. Find the manufacturer of your AVR on the
back of this guide.
3. Press and hold the Setup button on your
remote until the status LED changes from red
to green
Additional Feature: Aim Anywhere Control
See the back of this user guide to learn how
to pair your remote and set-top box* for Aim
Anywhere control, allowing you to control your
devices even when they are placed behind your
TV or in another room (up to 50 feet away).
*Aim Anywhere control is not supported by all
set-top boxes.
FCC Compliance Statement
This equipment has been tested and found
to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate
radio frequency energy and, if not used in
accordance with the instructions, may cause
harmful interference to radio communications.
There is no guarantee that interference will
not occur in a particular installation. If this
equipment does cause harmful interference
to radio or television reception, the user is
encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase or decrease the separation between the equipment and receiver.
• Connect the equipment into an outlet on
a circuit different from that which the receiver is connected.
• Consult the dealer or an experienced remote control/TV technician for help.
• It is strongly recommended that the TV
be plugged into a separate wall outlet.
The user is cautioned that changes and mod-
ications made to the equipment without the
approval of the manufacturer could void the
user’s authority to operate this equipment.
This device complies with part 15 of the FCC
rules. Operation is subject to the following
two conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
“CAUTION” : Exposure to Radio Frequency Radiation. Antenna shall be mounted in
such a manner to minimize the potential for
human contact during normal operation. The
antenna should not be contacted during operation to avoid the possibility of exceeding the FCC radio frequency exposure limit.
Helpful Tip: Additional remote control programming support, including code lookup tool and
frequently asked questions, can be found at
xnity.com/remotes.
4. Enter the rst code listed for the AVR manufacturer. The status LED should ash green
twice when the code is entered.
5. Press the TV Power button on the remote.
If the AVR turns off, you have successfully
programmed your remote. Turn the AVR back
on and press the VOL +/- and Mute buttons
to conrm they control the volume of your
device. If so, you’re all set!
6. If the AVR does not turn off or the VOL +/-
and Mute buttons do not work, repeat the
steps above using next code listed for the
device manufacturer. You may need to try
several codes to nd the one that works for
your device.
Page 2
Pairing your Xfinity Remote
for Aim Anywhere Control
Once your remote control is paired to your settop box it is uniquely paired and will not control
any other set-top box in your home unless you
pair it with another device.
If you would like to use your remote to control
multiple XFINITY set-top boxes simultaneously, you can remove Aim Anywhere pairing by
following the steps below.
1. Press and hold the Setup button on the
remote until the status LED changes from red
to green.
2. Press A on the remote. If the status LED
blinks green twice, you have successfully
removed Aim Anywhere control.
You can now use your remote to control other
Comcast set-top boxes simultaneously.
SETUP CODES FOR TVs
3M 10737, 11616, 11655
A-Mark 10003
Abex 10032
Accurian 11803
Acer 12244, 12245
Action 10873
ADC 12246
Admiral 10093, 10463, 12246, 12258,
12286
Advert 10761, 10783, 10815, 10817,
10842, 11933, 12267
Adventura 10046
Aftron 10891
Aiko 10092
Aiwa 10701, 11914, 12248, 12270
Akai 10030, 10060, 10098, 10672,
10702, 10812,11207, 11385,
11675, 11676, 11688, 11689,
11692, 11903, 11935
Alaron 10179, 10183, 10216
Albatron 10700, 10843
Amark 12286
Ambassador 10177
American Action 10180
Ampro 10751
Anaba 12249
Anam 10180
Anam National 10055
AOC 10030, 12250, 12268, 12284,
12287, 11590, 11365
Aomni 11623
Apex Digital 10156, 10748, 10879, 10765,
10767, 10879, 10890, 11991
Archer 10003, 12286
Aspect 12251
Astar 11531, 11738
Audiovox 10451, 10180, 10092, 10003,
10623, 10802, 10846, 10875,
11284, 11951, 11952
Aurora Systems 10801
Aventura 10171
Bang & Olufsen 12252
Belcor 10019, 12284
Bell & Howell 10154, 10016, 12246, 12293
BenQ 11032, 11315
BlueSky 12253, 12254
Bradford 10180
Brillan 11007, 11257, 11258
Brockwood 10019
Broksonic 10236, 10463, 12258
Brokwood 12284
Bush 10355,
Byd:sign 11309
Cadia 11283
Candle 10030, 10046, 10056, 10186,
12284
Canon 10793, 11396
Carnivale 10030
Carver 10054, 10170
Casio 10611, 11205
CCE 10217, 10329
Celebrity 10000
Celera 10765
Centrios 12255
Changhong 10765
Cineral 12253
Cinego 11986
Citizen 10060, 10030, 10092, 10046,
10056, 10186, 10280, 10561,
11669, 11671, 11672, 11928
11935, 12246, 12258, 12284,
12287
Clarion 10180
Classic 11984
CLP Classic 12284
Coby 12017, 12256, 12257
Colortyme 12284
Commercial 11447, 10047
Solutions
Compaq 10749
Concerto 10056, 12284
Contec 10180, 12287
Craig 10180
Crosley 10054
Crown 10180
CTX 12286
Curtis Mathes 10047, 10054, 10154, 10451,
10093, 10060, 10702, 10030,
10145, 10166, 10016, 10056,
10466, 10747, 11147, 11347,
11919, 12246, 12284, 12293
CXC 10180
CyberHome 10794
Cybervision 12253
Cytron 11326, 12003
Daewoo 10451, 10092, 10019, 10066,
11661, 10623, 10067,10091,
10661,10672,11909,11928,
12268, 12284
Daytron 10019, 12284
Dell 11264, 11080, 11178, 11403
Delta 11369
Denon 10145, 10511
Denstar 10628
Diamond Vision 11801, 11996, 12288
Digistar 11565, 12267
Digital Lifestyles 11765, 11822
Digital Projection 11482, 11725, 11726, 11750
Inc.
Dimensia 12293
Disney 12258, 12259
Dream Vision 11297
Dukane 12251
Dumont 10017
Durabrand 10463, 10180, 10178, 10171,
10003, 11034, 12258
Dwin 10093, 10747, 10774
Dynatech 10049
Dynex 11463, 11780, 11785
Elki 10735
Electroband 10000, 12287
Electrograph 11755, 11623
Electrohome 10463, 10446, 11570, 11670,
11672, 11760, 11761, 12284
Elektra 12246
Element 11687, 12260
Emerson 10154, 10451, 10236,
10463, 10180, 10178, 10171,
11963, 11928, 11913, 11911,
11909, 11905, 11665, 10282,
10280, 10270, 10183, 10181,
10179, 10177, 10038, 10019,
10623, 11963, 12248, 12258,
12270, 12284, 12285, 12288
Emprex 11422, 11546, 11765
Envision 10030, 10813, 11365, 12250,
12284
Epson 11122, 11290
Erae 11222
ESA 10812, 10171, 11963
Fisher 10154, 10159
Fujitsu 10179, 10186, 10683, 10853,
12008, 10809
Funai 10180, 10171, 10179, 11904,
11963, 11271, 12248, 12270
Futuretech 10180
Gateway 11755, 11756
GE 11447, 10047, 10051, 10451,
10178, 10021, 10027, 10029,
10055, 10135, 10279, 10282,
10747, 11907, 11919, 11922,
11347, 12284, 12290, 12293
Gibralter 10017, 10030, 10019, 12284
Go Video 10886, 11823, 11831
GoldStar 10178, 10030, 10002, 10019,
12248, 12268, 12269, 12270,
12271, 12284
Goodmans 10360
Gradiente 10392, 12284
Grundig 10683
Grunpy 10180, 10179
H & B 11366
Haier 11034, 10768
11009, 12295
Hallmark 10178, 12284
Hanns.G 11783
Hannspree 11348, 11745, 11783,
12261
Harley Davidson 10043, 10179, 11904
Harman/Kardon 10054, 10078
Harvard 10180, 10068
Hauppauge 12262
Havermy 10093
Helios 10865
Hello Kitty 10451
Hewlett Packard 11494, 11502, 11088, 11089,
11101
Hisense 10748, 11660, 12296
Hitachi 11145, 10145,12243,12143,
11904, 11345, 10797, 10737,
10724,10723,10413,10279,
10227, 10173, 10151, 10097,
10095, 10056, 10038, 10032,
10016, 11960, 12246, 12248,
12251, 12270, 12284
Hyundai 10849, 11219, 11294
I-Inc 11746
iLo 11286, 11603, 11665, 11684,
11990
Innity 10054, 12275
InFocus 10736, 10738, 10741, 10781,
11516, 12293
Initial 11990
Insignia 10171, 11780, 11892, 11204,
11326, 11517, 11641, 11963,
12002, 12258, 12263, 12264,
12267
Inteq 10017
IX 10877
Janeil 10046
JBL 10054
JCB 10000
JC Penney 12268, 12284, 12293
Jensen 10761, 10050, 10815, 10817,
11299, 11933, 12284
JVC 10053, 10036, 10160, 10169,
10731, 11349, 11253, 12265
Kamp 10216
Kawasaki 12266
Kawasho 10216, 10308, 12284
Kaypani 10052
KDS 11687
KEC 10180
Kenwood 10030, 10019, 12284
KLH 10765, 10767
Kloss 10024, 10046, 10078
Knoll Systems 10781
Konka 10628, 10632, 10638, 10707,
11385, 11831, 11939
Kost 11262, 11483
Kreisen 10876, 11474
KTV 10180, 10030, 10183, 10217,
10280, 12274, 12287
Kurazai 12246
Lasonic 12288
Legend 12267
LG 11265, 10178, 10700, 10442,
10856, 11178, 11530, 11637,
11758, 11934, 11993, 12248,
12268, 12269, 12270, 12271,
12284
Llyod’s 11904
Lodgenet 12246, 12293
Loewe 10136
Logik 10016, 12246, 12293
Luce 10837, 11031
Luxman 10056, 12284
LXI 10047, 10054, 10154, 10156,
10178, 10747, 12248, 12270,
12284, 12293
Magnavox 11454, 11866, 10054, 10030,
10706, 11990, 11963, 11913,
11904, 11525, 11365, 11198,
11254, 10386, 10802, 10230,
10187, 10186, 10179, 10096,
10036, 10028, 10024, 10020,
12275, 12284
Magnin 11907
Majestic 10015, 10016, 12246, 12293
Marantz 10054, 10030, 10704, 10854,
10855, 11398, 11554, 12284
Matsushita 10250, 10650
Maxent 11755, 11757
MB Quart 11868
Medion 12259
Megapower 10700
Megatron 10178, 10145, 10003, 12251,
12284
MEI 12287
Memorex 10154, 10463, 10150, 10178,
10016, 10179, 10877, 11570,
11911, 11920, 12246, 12258,
12284, 12293
MGA 10150, 10178, 10030, 10019,
10155, 11907, 12268, 12284
Micro 11436
Midland 10047, 10017, 10051, 10032,
10747
Mintek 11990, 11603
Minutz 10021
Mitsubishi 11250, 10093, 10150, 10178,
10014, 10019, 10098, 10155,
10331, 10358, 10592,10836,
10868, 11278, 11392, 12268,
12284
Monivisoin 10700, 10843
Montgomery Ward 12246, 12293
Motorola 10093, 10055, 10835, 12286
Moxell 10835
MTC 10060, 10030, 10019, 10049,
10056, 10091, 10216, 12268,
12284, 12287
Multitech 10180, 10049, 10217
Myron & Davis 12289
NAD 10156, 10178, 10866, 10037,
10056, 12284
Nakamichi 11493
Naxa 11998
NEC 10030, 10019, 10036, 10056,
10170, 10434, 10455, 10497,
10882, 11398, 11704, 11797,
12026, 12268, 12284
NetTV 11755
Nikko 10178, 10030, 10092, 12284
Niko 11581
Noblex 10430
Norcent 10748, 10824, 11089, 11365,
11590, 11591
Norwood Micro 11286, 11296, 11303
Noshi 10018
NTC 10092
NuVision 11657
Olevia 11144, 11240, 11331, 12272
Olympus 11342
Onwa 10180
Optimus 10154, 10250, 10166, 10650,
11913, 12273
Optoma 10887, 11348, 11674
Optonica 10093, 10165, 12286
Orion 10236, 10463, 11463, 10179,
11905, 11911, 12258
Panasonic 10250, 10051, 10055, 10650,
11291, 11941, 10162, 10226,
10375, 11310, 11410, 11919,
12273, 12274
Penney 10047, 10156, 10051, 10060,
10178, 10030, 11919, 11907,
10747, 10309, 10149, 10032,
10027, 10021, 10019, 10018,
10003, 10002, 11347
Petters 11523
Philco 10054, 10030, 10019, 10020,
10028, 10096, 10302, 12268,
12284
Philips 11454, 10054, 10037, 10690,
11483, 12275, 12284
Phillips-Magnavox 12275
Pilot 10030, 10019, 12284
Pioneer 10166, 10679, 10866, 10038,
10172, 11398, 12284
Piva 12277, 12276
Planar 11496
Polaroid 10765, 12063, 12002, 11991,
11962, 11769, 11767, 11766,
11762, 11687, 11565, 11538,
11523, 11385, 11341, 11328,
11327, 11326, 11316, 11314,
11286, 11276, 11262, 10865,
12267
Portland 10092, 10019, 12268, 12284
Prima 10761, 10815, 10817, 11389,
11785, 11933, 10783, 12267
Princeton 10700, 10717
Princeton Graphics 12286
Prism 10051
Proscan 11447, 10047, 11347, 10466,
10747, 11922, 12291, 12293
Proton 10178, 10003, 10031, 10052,
10466, 12284
Protron 11320, 11323
Proview 10835, 11687
Pulsar 10017, 10019, 12284
Puneet 11546
Pvision 11222
Quasar 10250, 10051, 10055, 10165,
10650, 10219, 11919, 12273,
12274
RadioShack 10047, 10154, 10180, 10178,
10030, 10165, 12248, 12270,
12284, 12290, 12293
RCA 11447, 10047, 12002, 11953,
11948, 11922, 11919, 11907,
11781, 10747, 10278, 10254,
10090, 10679, 11047 11147,
11247, 11347, 11547, 11958,
10038, 10029, 10019, 10018,
12268, 12284, 12290, 12291,
12292, 12293
Realistic 10154, 10180, 10178, 10030,
10165, 10019, 10032, 10056,
12248, 12270, 12284, 12293
RevolutionHD 11623
Rhapsody 10183, 10216, 12287
Runco 10017, 10030, 10497, 10612,
11398, 11629
Sampo 10030, 11755, 10032, 10052,
11597, 12284
Samsung 10812, 10702, 10178,
10030, 11959, 11632, 11575,
11060, 10814, 10766, 10587,
10482, 10427, 10408, 10329,
10217, 10056, 10032, 10019,
11903, 12268, 12280, 12281,
12284
Sansui 10463, 11409, 11904, 11911,
11935, 12258, 12282
Sanyo 10154, 10088, 10159, 10232,
10484, 10735, 10798, 10799,
11907, 12284
Sceptre 10878, 11360, 11599
Scimitsu 10019
Scotch 10178, 12284
Scott 10236, 10180, 10178, 10019,
10179, 10309, 11711, 12284
Sears 10047, 10054, 10154, 10156,
10178, 10171, 10015, 10149,
10159, 10168, 10179, 10747,
11007, 11904, 10056, 12284,
12293
Seleco 10737, 11297
Selectron 12283
Sharp 10093, 10153, 10165, 10386,
11602, 10491, 10851, 12284,
12285, 12286
Sharper Image 11950
Sheng Chia 10093
Sherwood 11399
Shogun 10019, 12284
Signature 10016, 12246, 12293
Signet 10800, 10844, 11262
SIM2 Multimedia 11297
Simpson 10186, 10187
Skyworth 11799
Solarism 11220
Sole 10813, 11031, 11366, 11377,
11483, 11530, 11623, 12075,
12076
Sonic 12287
Sony 11100, 10000, 10011,
10353, 10834, 11317, 11400,
11685, 11786, 11791, 11904,
11925
Soundesign 10180, 10178, 10179, 10186,
12284
Sova 11320, 11952
Soyo 11546, 11746, 11824, 11826,
11828, 11830, 11831
Spectra 12288
Spectricon 10003
Spectroniq 11687
Squareview 10171
SSS 10180, 10019, 12284
Starlite 10180
Studio Experience 10843
SunBrite 11420, 11435
Superscan 10093, 10864
Supra 12284
Supre-Macy 10046
Supreme 10000
SVA 10748, 10587, 10768, 10865,
10870, 10871, 10872, 12289
Sylvania 11864, 10054, 10030, 10171,
11271, 10020, 10028, 10065,
10096, 11314, 11665, 11963,
12248, 12258, 12270, 12284
Symphonic 10180, 10171, 11904, 11913,
12248, 12270
Syntax 11144, 11240, 11331,11610
Tandy 10093, 10218, 12286
Tashiko 10588
Tatung 10003, 10049, 10055, 11101,
11286, 11287, 11288, 11361,
11503, 11756
TCL 12290, 12291, 12292, 12293
Technics 10250, 10051
Technol Ace 10179
Techview 10847, 12004
Techwood 10051, 10003, 10056, 12284
Teknika 10054, 10180, 10150, 10060,
10092, 10016, 10019, 10056,
10175, 10179, 10186, 10312,
12246, 12268, 12284, 12293
Telefunken 10702, 10056, 10101
Telemagic 10735
Telernet 12246, 12293
Tera 10031, 12284
Thomas 11904
Thomson 10209, 10210, 10625
TMK 10178, 10056, 10177, 12284
TNCi 10017
Toshiba 10154, 11256, 10156, 10060,
10036, 10650, 10845, 10149,
10736, 10832, 11343, 11369,
11704, 11935, 11156, 11356,
11656, 11265, 12294
TruTech 11723, 12066
TVS 10463
Ultra 10391, 11323
Universal 10027
US Logic 11286, 11303
Vector Research 10030
Venturer 11865
VEOS 11007
Victor 10053
Video Concepts 10098
Vidikron 10054, 10242, 11398, 11629
Vidtech 10178, 10019, 10036, 12268,
12284
Need to Remove
Aim Anywhere Control?
© Comcast Corporation. All rights reserved.
© Comcast Corporation. Derechos Reservados.
Viewsonic 11755, 12014, 10724, 10775,
10797, 10857, 10864, 10885,
11330, 11342, 11578, 11627,
11742
Viking 10046, 10312
Viore 11207, 11684, 12278, 12279
Visart 11336
Vizio 11758, 10864, 10885, 11756,
12247
Wards 10054, 10178, 10030, 10016,
10019, 10020, 10021, 10027,
10028, 10029, 10056, 10096,
10165, 10179, 10866,
11156, 12246, 12268, 12284,
12293
Waycon 10156
Westinghouse 10000, 10451, 10885, 10889,
10890, 11282, 11577
White Westinghouse 10463, 10623, 11909, 12248,
12270
WinBook 11381, 11503
Wyse 11365
Xoceco 11469
Yamaha 10030, 10019, 10797, 11407,
12268, 12284
Zenith 10017, 10463, 11265, 10178,
10092, 10016, 11904, 11909,
11911, 12246, 12248, 12251,
12285, 12258, 12265, 12270,
12271, 12275, 12284
Zonda 10003
SETUP CODES FOR AVRs &
SOUNDBARS
ADC 30531
Aiwa 31964, 30158, 30189
Bose 31934, 31935, 31229, 31933
Boston Acoustics 31944
B&W 31940, 31941
Capetronic 30531
Carver 30189
Coby 31946
Denitive 31936
Denon 31961, 31104, 31360
GE 30078
Harman/Kardon 30110, 30189, 31955
Ilive 31957
Insignia 31960
Integra 30135
JBL 31958, 30110
JVC 30074, 30331
Kenwood 30027, 31027, 31313,31570
KHL 31967
LG 31953
Linn 30189
Magnavox 30189, 30531
Marantz 31972, 30189
NAD 31973, 31974
Onkyo 31965, 30135
Optimus 30531, 31023
Panasonic 31959, 31308, 31518
Philips 31945, 31962, 30189, 31266
Pinnacle 31954, 31971
Pioneer 31963, 30531, 31023, 31384
Polk Audio 31951, 31952, 30189
Proscan 31254
RCA 30531, 31023, 31254
Regent 31968, 31969
Rio 31970
Samsung 31949, 31950
Sansui 30189
Sharp 31942, 31956
Sony 31938, 31939, 30158, 31758,
31759
Soundesign 30078
Stereophonics 31023
Sunre 31313
Technics 31959, 31308, 31518
Thomson 31254
Victor 30074, 30331
Vizio 31937, 31975
Wards 30078, 30158, 30189
Yamaha 31947, 31948, 30176, 30354,
31176
ZVox 31943
Your XFINITY Remote can be paired with Aim
Anywhere devices, including select set-top
boxes, allowing you to control your devices
even when they are placed out of line-of-sight
(for example, in an entertainment center or
behind your TV). XFINITY Remotes can be
identied by a model number beginning with
“XR” on the back of the remote.
Aim Anywhere Pairing:
1. Press and hold the Setup button for 3
seconds, until the status LED changes
from red to green.
2. Press the XFINITY button on the remote.
Your TV should display on-screen instructions to enter a 3-digit code. If the instructions do not appear, press the XFINITY
button again - up to 2 more times.
3. Follow the on-screen instructions to enter
the 3-digit code that appears.
4. Once the code is correctly entered, your
XFINITY Remote is paired with the device.
:Q Why does the status LED ash red then
green then red during pairing?
:A The set-top box you are attempting to pair
may not be powered on, or may not support
Aim Anywhere control. If the on screen
instructions to enter a 3-digit code do not
display on your TV when attempting to pair,
your set-top box does not support Aim
Anywhere control.
:Q When paired, why does the status LED
ash green then red when pressing a
button on the remote?
:A The set-top box that is paired with your re-
mote may not be powered on or may be out
of range. If your device is powered on and
within 50 feet of the remote, try re-pairing
your remote.
Frequently Asked Questions
about Aim Anywhere Control:
Loading...