Tyro™ 8000 Series
Instruction Manual
Tyro
™
Infant Car Seat
L
A
T
C
H
L
o
w
e
r
A
n
c
h
o
r
a
n
d
T
e
t
h
e
r
f
o
r
C
H
i
l
d
r
e
n
• Certified for use in motor vehicles and
aircraft.
• Meets or exceeds all applicable
requirements of Federal Motor Vehicle
Safety Standard 213.
Para instrucciones en Español,
llamar al: 1-800-992-6624.
Correct installation and use can be
a matter of Life or Death! Read and
understand these instructions before
using this car seat.
WARNING
TICS1203e (EN).qxd 4/4/05 4:15 PM Page 1
Section 1. Table of Contents......................................................................................................................1
Section 2. Warnings..................................................................................................................................3
Section 3. Proper Use Check List..............................................................................................................4
Section 4. Tyro™ Infant Car Seat Parts.....................................................................................................5
Section 5. Use Recommendations............................................................................................................6
Section 6. Securing Infant in Car Seat......................................................................................................7
Section 7. Selecting A Vehicle Seating Location.......................................................................................
9
Section 8. LATCH System......................................................................................................................
11
Section 9. Installation Of Infant Car Seat In Vehicle................................................................................
12
• Attachment Of Infant Car Seat To Base.........................................................................12
• Securing Base With LATCH System.............................................................................13
• Securing Base With Vehicle Seat Belt............................................................................17
• Securing Infant Car Seat Without Base.........................................................................
19
Section 10. Stroller or Travel System Use................................................................................................
21
Section 11. Operation and Adjustment
• Changing Harness Use Position................................................................................... 22
• Harness Use and Adjustment........................................................................................23
• Carry Handle Operation................................................................................................
23
• Base Adjustment...........................................................................................................
24
• Infant Insert................................................................................................................... 24
• Canopy.......................................................................................................................... 24
1
Section 1 - Table of Contents
TICS1203e (EN).qxd 4/4/05 4:15 PM Page 2
2
Section 12. Vehicle Seat Belt Systems....................................................................................................25
Belt Lock-off.......................................................................................................28
Section 13. Additional Information
• Certification............................................................................................30
• Aircraft Use....................................................................................................................30
• Warm Weather...............................................................................................................
30
• Vehicle Seat Protection..................................................................................................
30
• Car Seat Useful Life.......................................................................................................30
• Instruction Manual Storage............................................................................................30
Section 14. Care and Cleaning.................................................................................................................31
Section 15. Registration Information........................................................................................................
32
Keep this instruction manual for future use.
Store instruction manual inside LATCH storage
compartment located on front of base.
TICS1203e (EN).qxd 4/4/05 4:15 PM Page 3
3
Section 2 - Warnings
WARNING
DEATH or SERIOUS INJURY can occur
• Failure to follow these instructions and car seat labels can result in injury or death to a child
from striking the vehicle’s interior during a sudden stop or crash.
• Use only in a rear-facing position when using this infant car seat in the vehicle. Serious
crippling injury or death can result if infant faces front of vehicle.
• Use only with children who weigh 22 pounds (10 kg) or less and whose height is 29 inches
(74 cm) or less.
• Discontinue use when infant’s weight exceeds 22 pounds (10 kg).
• Snugly adjust harness provided with the car seat around child. Infant MUST be secured by
harness system at all times, when infant seat is used in vehicle or outside of vehicle.
• For proper harness fit, infant insert MUST be used with small infants.
• Secure this child restraint with the vehicle’s LATCH System if available or with a vehicle seat belt
as shown in this manual.
• LATCH System or vehicle seat belt MUST stay tightly adjusted around car seat at all times.
• Secure this child restraint to the vehicle, even when not occupied. Unsecured items may injure
occupants in a crash.
• DO NOT use car seat if it has been in a crash, it must be replaced. A crash can cause unseen
damage and continued use could result in serious injury or death.
• DO NOT use infant car seat if it is damaged, missing instructions, or missing parts.
• Register your child restraint with the manufacturer.
Proper Use Is Required:
No car seat can guarantee protection from injury in every situation, but proper use helps reduce the risk of
serious injury or death.
TICS1203e (EN).qxd 4/4/05 4:15 PM Page 4
• Proper use is required. Read and understand instructions and car seat labels.
• Use this infant car seat rear-facing only.
• Snugly adjust harness straps around child.
• Securely install car seat with LATCH System or vehicle seat belt as specified in this instruction manual.
• Do not use this infant car seat in a front vehicle seating location with an air bag.
• Secure children in back seat whenever possible.
• Never leave child unattended.
• Do not allow anyone (babysitter, relatives, etc.) to use car seat without first understanding all instructions.
Need help installing your infant car seat?
Contact one of the following sources:
• Your vehicle dealer to locate a child safety seat inspection station in your area.
• Call 1-866-SEAT CHECK (1-866-732-8243).
• Visit www.nhtsa.dot.gov and select “Child Seat Inspections”.
• Visit www.seatcheck.org.
• Contact a certified child passenger safety technician in your area. To locate a certified “Child Passenger
Safety” Technician in your area visit www.nhtsa.dot.gov and select “Child Passenger Safety” and then
select “Technician Contact Locator”.
4
Section 3 - Proper Use Check List
TICS1203e (EN).qxd 4/4/05 4:15 PM Page 5
5
INFANT CAR SEAT
Shoulder
Harness Slot
Chest Clip
Buckle
with
Tongues
Harness
Adjuster Lever
Crotch Strap
Carry
Handle
Canopy
Not Shown
(see page 24)
Vehicle Lap
Belt Guide
(Without Base)
Shoulder
Harness Strap
Metal Crotch
Strap Anchor
Vehicle
Shoulder
Belt Guide
Harness
Adjuster Strap
Shoulder Harness
Strap Cover
Infant Insert
Metal Harness
Strap Clips
Red Release
Handle
Section 4 - Tyro™Infant Car Seat Parts
Recline
Indicator
Stroller
Latch
Handle
Button
Stroller
Latch
Metal
Rod
Stroller
Latch
Harness
Safety
Cover
TICS1203e (EN).qxd 4/4/05 4:15 PM Page 6
Tyro™8000 Series
Instruction Manual
Tyro
™
Infant Car Seat
®
L
A
T
C
H
L
o
w
e
r
A
n
c
h
o
r
a
n
d
T
e
t
h
e
r
f
o
r
C
H
i
l
d
r
e
n
•Certified for use in motor vehicles and
aircraft.
•Meets or exceeds all applicable
requirements of Federal Motor Vehicle
Safety Standard 213.
Para instrucciones en Español,
llamar al:1-800-992-6624.
Correct installation and use can be
a matter of Life or Death! Read and
understand these instructions before
using this car seat.
WARNING
6
CAR SEAT BASE
Belt Lock-Off
Recline
Adjustment Knob
LATCH Lower
Anchor Belt
Belt Path Tabs
Height and Weight Limits:
This infant car seat is designed for rear-facing use only by infants whose:
-Weight is 22 pounds (10 kg) or less and height is 29 inches (74 cm) or less.
Infants With Special Needs
A preterm infant or low birth weight infant may be at special risk traveling reclined in a vehicle or aircraft. According
to the American Academy of Pediatrics, these infants may be at increased risk of suffering breathing or other
difficulties if improperly reclined or positioned in a car seat.
Have your physician or hospital staff evaluate your infant in this car seat before you and your infant leave the
hospital. If your infant is not able to travel in a reclined position, DO NOT use this car seat. Use a car bed for your
infant.
LATCH Compartment
Red Recline
Adjustment Button
Section 5 - Use Recommendations
Instruction
Manual
Base
Recline
Adjuster
TICS1203e (EN).qxd 4/4/05 4:15 PM Page 7
C
MBI
1
Position harness to fit infant:
- Shoulder harness straps must be through shoulder harness slots at or just below infant’s shoulders.
- Infant insert MUST be used for small infants.
See “Operations and Adjustments” section to change position of harness.
Loosen harness - while pressing on harness adjustment lever, pull harness straps out.
Place infant in car seat with back and rump contacting seating surfaces (fig. a).
7
(fig. a)
Section 6 - Securing Infant In Car Seat
2
3
WARNING
DEATH or SERIOUS INJURY can occur
• Keep harness straps snug and positioned on shoulders and thighs. Infant MUST be secured by
harness system at all times, when infant seat is used in vehicle or outside of vehicle.
• For proper harness fit, infant insert MUST be used with small infants.
• Harness safety cover MUST be present and snapped onto metal rod to allow proper harness adjustment.
• Discontinue the use of the infant insert when:
- Child’s shoulders are above middle belt slots in seat back of car seat.
- Shoulder belts become too short to fit infant (approximately 5 months of age).
• Child must be dressed in clothing with arms and legs that will not interfere with buckling, snugly adjusting
or positioning harness.
• DO NOT use accessories or parts other than those provided by Combi USA, Inc. Use of
accessories or parts from other manufacturers could alter the performance of the car seat.
• Never leave child unattended, even when sleeping.
• Suffocation Hazard: Infant car seat can roll over on soft surfaces and suffocate child. Never place infant
car seat on beds, sofas or other soft surfaces.
• Strangulation Hazard: Child can strangle in loose harness straps. Never leave child in an infant car seat
when straps are loose or undone.
• Fall Hazard: Child’s movement can slide infant car seat. Never place infant car seat near edges of
countertops, tables or other elevated surfaces.
TICS1203e (EN).qxd 4/4/05 4:15 PM Page 8
Place harness straps over child’s shoulders and thighs.
Place top of buckle tongues together and insert buckle tongues into buckle (fig. b).
You should hear a click.
Pull up on tongues to be sure they are locked.
Pull harness adjuster strap (fig. c) to snugly adjust harness straps.
- Check that harness straps are snug on shoulder and thighs. Straps should not
allow a finger to pass between the belt and the child’s shoulder.
-Asnug harness strap should not allow any slack. It lies in a relatively straight line
without sagging. It does not press on the child’s flesh or push the child’s body into an
unnatural position.
NOTE: If harness can not be snugly adjusted as described above, do not use
this infant car seat.
Close chest clip and position chest clip at arm pit level (fig. d).
Small infants:
For a small infant, a rolled towel can be used on each side for support (fig. d).
Towels MUST not interfere with the ability to snugly adjust the harness system.
DO NOT place towel or other items behind infant or between infant and harness.
(fig. b)
Click
8
(fig. c)
(fig. d)
Harness
Adjuster
Strap
Pull
Chest Clip
Rolled Towel
4
7
6
5
TICS1203e (EN).qxd 4/4/05 4:15 PM Page 9
National Highway Traffic Safety Administration (NHTSA) alerts vehicle owners that according to accident statistics,
children up to age 12 are safer when properly restrained in the rear seating positions rather than the front seating
positions.
Refer to vehicle owner’s manual for car seat installation instructions for your vehicle.
- Use car seat in a rear vehicle seat location whenever possible.
- Never put a car seat in a front seat location unless recommended
by vehicle owner’s manual.
-DONOT use on front seat with an air bag.
- For vehicles with air bags, refer to vehicle owner’s manual for child
restraint installation information.
WARNING
DEATH or SERIOUS INJURY can occur
• DO NOT use this car seat in a vehicle front seating location with an air bag.
• Never put a car seat in a front vehicle seat unless recommended by vehicle owner’s manual.
9
1
2
Section 7 - Selecting A Vehicle Seating Location
TICS1203e (EN).qxd 4/4/05 4:15 PM Page 10
NO coloque el asiento infantil para el automóvil orientado hacia
atrás en el asiento delantero del vehículo que tenga una bolsa
neumática de seguridad. El niño podría MORIR O SUFRIR
LESIONES GRAVES. El asiento trasero es el lugar más seguro
para los niños de 12 años o menores.
DO NOT place rear-facing child seat
on front seat with air bag. DEATH OR
SERIOUS INJURY can occur.
The back seat is the safest place for
children 12 and under.
WARNING
DO NOT use car seat on vehicle seats which face the side
(fig. a) or face the rear (fig. b) of the vehicle.
Options For Securing A Car Seat:
This infant car seat can be secured to a vehicle using a standard
vehicle seat belt or the new LATCH System.
1. LATCH System:
LATCH stands for Lower Anchorage and Tether for CHildren.
The LATCH System can be used when securing the car seat with the base.
Starting with model year 2003 vehicles are equipped with LATCH Systems. See “LATCH System”
section for more information. Check vehicle owner’s manual to determine if your vehicle has the
LATCH System that may be identified with the symbol in fig. c.
Some vehicle owner’s manuals may identify the LATCH System as “ISOFIX”. An ISOFIX System
can be used in the same way as the LATCH System.
If your vehicle has the LATCH System, the LATCH System should be used whenever possible.
2. V
ehicle Seat Belt:
The car seat with the base or without the base can be secured using vehicle seat belts.
If your vehicle does not have LATCH System, the car seat MUST be secured to the vehicle using a vehicle
seat belt.
Check vehicle owner’s manual for seating locations recommended for car seat use.
10
(fig. a)
(fig. b)
(fig. c)
3
TICS1203e (EN).qxd 4/4/05 4:15 PM Page 11
LATCH System On This Car Seat:
The LATCH System on the Tyro
™ Car Seat consists of a lower anchor belt with lower anchor
connectors .
The lower anchor connectors on the car seat connect to the LATCH System in a vehicle.
LATCH System On Vehicles:
Child restraint anchorage system or the LATCH System in the vehicle consists of two lower
anchorages located at the vehicle seat bight and a top tether anchorage (fig. b). Refer
to vehicle owner’s manual for seating locations which have the LATCH System.
The Tyro™ uses the lower anchor anchorages but does not use the top tether.
Lower anchorages are visible in some vehicles and others are not. Those that are not
visible are identified by a solid color round dot on the vehicle upholstery or a round dot with
a picture of a car seat in the center as shown in fig. c.
The vehicle manufacturer may provide funnel guides to separate the
vehicle seat cushions providing easier access to the lower anchorage.
See vehicle owner’s manual.
11
2
4
5
(fig. c)
(fig. b)
5
3
1
3
(fig. a)
2
2
1
4
Section 8 - LATCH System
TICS1203e (EN).qxd 4/4/05 4:15 PM Page 12
12
Attachment Of Infant Car Seat To Base:
Section 9 - Installation of Infant Car Seat in Vehicle
WARNING
DEATH or SERIOUS INJURY can occur
• Use only in a rear-facing position when using this infant car seat in the vehicle.
• Secure this child restraint with LATCH System or a vehicle seat belt as shown in this manual.
• LATCH System or vehicle seat belt must stay tightly adjusted around car seat or base at all times. If
LATCH System or vehicle seat belt does not stay tight, read the vehicle owner’s manual and “Vehicle Seat
Belts” section in this manual.
• Rear-facing car seat must be properly reclined:
-Too reclined can result in injury or ejection.
-Too upright can result in breathing difficulties.
• After installing infant car seat into base, lift carrier to be sure it is securely locked.
Removal Of Infant Car Seat From Base:
Push in handle buttons on each side of handle and rotate handle to upright carry position
(see “Carry Handle Operation” section).
Lift red release handle up , rotate infant car seat forward and lift car seat from
base (fig. a).
1
2
3
(fig. a)
1
2
3
1
2
Red Release
Handle
TICS1203e (EN).qxd 4/4/05 4:15 PM Page 13
13
Attaching Infant Car Seat To Base:
Verify that there are no objects on top of base or between base and infant car seat.
Lower car seat into base and push down on car seat to lock car seat into base (fig. b).
Test to be sure car seat is locked in base. Lift infant car seat at top of seat back
(fig. c) and at front end.
Carry handle can be moved to the vehicle use position (see “Carry Handle
Operation” section).
Adjust recline using recline indicator on the side of car seat. Line on
recline indicator MUST be in green striped zone (fig. d).
If line is not in green striped zone, adjust base (see “Base Adjustment” section), and
recheck recline of car seat. Repeat until recline indicator is in green striped zone.
If base can not be adjusted to locate the line in the green striped zone:
1. Try a different seating position.
2. Do not use this infant car seat.
NOTE: Vehicle must be parked on horizontal surface during this installation.
1
(fig. b)
4
(fig. c)
WARNING
DEATH or SERIOUS INJURY can occur
• Only use the car seat LATCH System in vehicle seating locations recommended by the vehicle
manufacturer for use with LATCH and have an anchor spacing of 280 mm (11 inches).
• LATCH connectors must be secured to the vehicle LATCH anchorages only. Connection to other vehicle
components could result in the anchor tearing free in a crash.
• Never attach more than one anchor connector to a vehicle lower anchorage unless recommended by the
vehicle owner’s manual for that vehicle.
Securing Base With LATCH System:
2
3
(fig. d)
Recline
Indicator
Green
Striped
Zone
5
TICS1203e (EN).qxd 4/4/05 4:15 PM Page 14
14
Refer to vehicle owner’s manual to identify the seating locations with LATCH
System. Select the seating location to be used and locate the vehicle lower
anchorages at the seat bight.
ALATCH Anchorage System with 280 mm (11 inches) spacing may not be available in
your vehicle in the rear center seating position. If use of the rear center position is
preferred, use the vehicle seat belt to secure the car seat. See “Securing Base
With Vehicle Seat Belt” section.
Remove car seat from base.
Remove the LATCH lower anchor belt with lower anchor connectors from the LATCH
compartment in base (fig. a).
Lengthen lower anchor belt. While pressing down on release button on top of
belt adjuster, pull belt to extend the length of lower anchor belt (fig. b).
Position the lower anchor belt with the belt adjuster slide buttons facing away from the
car seat. If the adjuster is not in that position, turn the belt and adjuster over.
Place the lower anchor belt under both belt path tabs in the base (fig. c). Belt Lock-off will
be under LATCH belt. Check that the belt is not twisted.
Adjust vehicle seat back into most upright position.
Place base rear-facing in the vehicle seat location
selected with LATCH belt toward vehicle seat back
and centered between the vehicle lower anchors
(fig. d).
(fig. a)
(fig.d)
(fig. b)
Lower
Anchor Belt
Adjuster
Slide Button
Pull
1
3
4
5
6
7
2
(fig. c)
LATCH
Compartment
8
LATCH
Lower Anchor
Belt
Adjuster
Belt
TICS1203e (EN).qxd 4/4/05 4:15 PM Page 15
15
Attach car seat to base.
Adjust recline using recline indicator on the side of the car seat. Line of recline indicator
MUST be in green striped zone (fig. e). If line is not in green striped zone, adjust base
(see “Base Adjustment” section), and recheck recline of car seat. Repeat until recline
indicator is in green striped zone.
If base can not be adjusted to locate the line in the green striped zone:
1. Try a different seating position.
2. Do not use this infant car seat.
NOTE: Vehicle must be parked on horizontal surface during this installation.
Remove car seat from base.
With hook-on connector opening facing down , position the opening of the
connector over the vehicle lower anchorage. Push down and then pull out on the
connector to lock it onto the vehicle anchorage (fig. f). You should hear a click.
Pull on connector to be sure it is locked onto the anchorage.
Repeat for connector on opposite side.
Tighten lower anchorage belt to secure the base. Press down in center of base to depress
the vehicle cushion and pull free end of lower anchor belt to tighten belt around base
(fig. g).
Check for secure installation. Pull base front to back and left to right
to check for secure installation (fig. h). LATCH belt MUST stay tight.
If LATCH belt does not stay tight or base can not be securely installed,
try a different LATCH location or use the vehicle’s seat belt to secure
the base.
Attach car seat to base.
Recheck recline of car seat. Adjust if necessary (see step 9).
(fig. f)
(fig. h)
(fig. e)
8
9
10
11
12
13
14
15
2
3
1
2 3
1
(fig. g)
TICS1203e (EN).qxd 4/4/05 4:15 PM Page 16
16
Removal Of Base Installed With LATCH:
Loosen lower anchor belt. Pressing down in center of base to reduce tension on lower
anchorage belt push adjuster slide button and loosen belt.
Press and hold the connector retainer spring .
Push connector in, then rotate connector , and pull out 3 to unhook from the vehicle
anchorage (fig. a). If the connector can’t be rotated, push in and lift the connector to
unhook from the vehicle anchorage.
Repeat to remove connector on opposite side.
Storage Of Lower Anchorage Belt And Lower Anchor Connectors:
When not using the LATCH System, fold the anchor belt and lower anchor
connectors and place inside LATCH compartment in base (fig. b).
(fig. b)
(fig. a)
1
2
3
LATCH
Compartment
1
2
3
1
2 3
Base
TICS1203e (EN).qxd 4/4/05 4:15 PM Page 17
17
Securing Base With Vehicle Seat Belt:
Refer to vehicle owner’s manual to identify the seating locations which can be used with a
car seat. Check for specific instructions for car seat use.
After selecting a seating location, adjust vehicle seat back into most upright position.
Place base with car seat attached rear-facing on vehicle seat with belt path tabs towards
vehicle seat back (fig. a).
Adjust recline of car seat. Line inside recline indicator MUST be in green striped
zone (fig. a). If line is not in green striped zone, adjust base (see “Base
Adjustment” section), and recheck recline of car seat. Repeat until recline
indicator is in the green striped zone.
If base can not be adjusted to locate the line in the green striped zone:
1. Try a different seating position.
2. Do not use this infant car seat.
NOTE: Vehicle must be parked on horizontal surface during this installation.
Remove car seat from base.
Route vehicle seat belt through base:
a. Locate vehicle seat belt buckle that will be used to secure the base and
arrow on the blue belt lock-off.
b. The arrow on the belt lock-off must point toward the vehicle buckle that
will be used to secure the vehicle belt (fig. b).
(fig. a)
(fig. b)
WARNING
DEATH or SERIOUS INJURY can occur
• Not all vehicle seat belts can be used with a car seat. Read vehicle owner’s manual and “Vehicle Seat
Belts” section in this manual.
2
3
4
5
6
1
Vehicle
Buckle
TICS1203e (EN).qxd 4/4/05 4:15 PM Page 18
(fig. d)
(fig. f)
!
18
c. If the arrow on the belt lock-off is not pointing in the correct direction, it must be
rotated so it points toward the vehicle buckle (fig. c).
d. Once the belt lock-off is in position pointing toward the vehicle buckle, open the belt
lock-off by lifting locking tab and then belt lock-off cover (fig. d).
e. Place vehicle lap belt and shoulder belt under both belt path tabs and through belt
lock-off (fig. e).
Tighten vehicle belt to secure the base. Press down in center of base to depress the
vehicle cushion while tightening vehicle belt (fig. f).
Close belt lock-off over seat belts closing belt lock-off cover first and then the locking tab.
Check for secure installation. Pull base front to back and left to right to check for secure
installation (fig. g). Vehicle lap belt MUST stay tight.
If the vehicle lap belt does not stay tight, check that the belt lock-off is locked and that the
arrow is pointing toward the vehicle buckle being used. If the base still does not stay
tight, see vehicle owner’s manual, “Vehicle Seat Belts” section or move to a different
seating location.
Attach car seat to base.
Recheck recline of car seat. Adjust if necessary (see step 4).
2
1
7
9
11
(fig. g)
(fig. c)
(fig. e)
1
2
1
Belt Lock-off
Open
8
10
TICS1203e (EN).qxd 4/4/05 4:15 PM Page 19
Securing Infant Car Seat Without Base:
Refer to vehicle owner’s manual to identify the seating location which can be used
with a car seat. Check for specific instructions for car seat use.
After selecting a seating location, adjust vehicle seat back into most upright position.
Place car seat rear-facing on vehicle seat.
Carry handle can be moved to the vehicle use position (see “Carry Handle Operation”
section).
Thread vehicle lap belt through vehicle lap belt guides on car seat (fig. a) and
buckle vehicle belt. Be sure vehicle lap belt is not twisted. Do not place
shoulder belt through vehicle lap belt guides.
Press down firmly on car seat to compress vehicle seat cushion while tightening
vehicle lap belt (fig. b).
Adjust recline using the recline indicator on the side of car seat (fig. a). Line on recline
indicator must be in green striped zone.
If line is not in green striped zone, place a tightly rolled up towel, blanket or firm foam
(pool noodle) under end of car seat contacting vehicle seat back.
If base can not be adjusted to locate the line in the green striped zone:
1. Try a different seating position.
2. Do not use this infant car seat.
NOTE: Vehicle must be parked on horizontal surface during this installation.
(fig. a)
Vehicle Lap
Belt Guides
Towel or
Pool Noodle
Level
Indicator
(fig. b)
19
WARNING
DEATH or SERIOUS INJURY can occur
• Not all vehicle seat belts can be used with a car seat. Read vehicle owner’s manual and “Vehicle Seat
Belts” section in this manual.
2
3
4
5
6
1
7
TICS1203e (EN).qxd 4/4/05 4:15 PM Page 20
Check for secure installation. Pull front to back and left to right to check for secure
installation (fig. c). Vehicle lap belt MUST stay tight.
If vehicle lap belt does not stay tight, see “Installation with Lap/Shoulder Belts” below.
Recheck car seat recline. Verify line is in green striped zone of recline indicator.
Installation with Lap/Shoulder Belts:
•When using vehicle lap/shoulder belts, shoulder belt may be used for additional support.
Place shoulder belt around back of Tyro™ (fig. d) and through the vehicle shoulder belt
guide on back of car seat shell (fig. e). If shoulder belt is too short to go around back of
Tyro™, position shoulder belt through the lap belt guide above the vehicle buckle and
against vehicle seat back (fig. f). Do not route shoulder belt through lap belt guides on
both sides of car seat.
•Lap/shoulder belt with free sliding latch plate:
- Pull out on latch plate (fig. g). If belt slides freely through latch
plate, a belt lock-off must be used as described in “Belt Lock-off”
section.
- Some combination lap/shoulder belts with free sliding latch plates
may be converted into an “automatic locking mode” that will allow
use without a belt lock-off. See vehicle owner’s manual and label
on vehicle belts for instructions.
Removal Of Infant Car Seat From Vehicle:
Unhook shoulder belt from behind car seat and unbuckle vehicle
seat belt.
Remove lap belt from vehicle lap belt guides.
Push in handle buttons on each side of handle and rotate to
upright carry use position (see “Carry Handle Operation” section).
Remove car seat from vehicle.
20
(fig. e)
(fig. c)
(fig. d)
Shoulder
Belt Guide
8
9
1
2
3
4
Shoulder
Belt
(fig. g)(fig. f)
Latch
Plate
TICS1203e (EN).qxd 4/4/05 4:15 PM Page 21
21
This infant car seat can only be used with Combi stroller models to transport your infant.
Check Combi stroller information or the Combi USA, Inc. website at www.combi-intl.com, for an
updated list of stroller models.
See stroller instructions for securing car seat and use information.
Section 10 - Stroller or Travel System Use
TICS1203e (EN).qxd 4/4/05 4:15 PM Page 22
Changing Harness Use Position
Shoulder harness straps must be through slots at or just below shoulder.
To change shoulder belt slots:
1. Buckle harness and chest clip.
2. From front of car seat, loosen harness straps by pressing harness adjuster lever and
pulling harness straps out to lengthen them.
3. From back of car seat, rotate harness safety cover out, unhook both harness
strap metal clips from adjuster loop (fig. a).
4. From front of car seat, pull harness straps out through car seat shell, seat pad
and infant insert.
To Re-secure Harness Belts:
1. From front of car seat, rethread harness straps through desired harness strap
slots of infant insert, seat pad and seat back.
NOTE: Only use two lowest sets of shoulder belt slots with infant insert.
2. From back of car seat, route shoulder belts between plastic seat
and metal rod. Pull harness straps down and re-attach harness
strap metal clips to adjuster loop as shown in fig. c. Make sure
harness straps are not twisted and are threaded through
matching slot of seat pad and seat back.
3. Close harness safety cover, snap onto metal rod.
22
(fig. a)
Harness
Strap Metal
Clip
(fig. c)
Adjuster
Strap
Loop
Section 11 - Operation and Adjustment
WARNING
• Shoulder belts MUST be through belt slots in infant insert.
• Do not use infant insert with top slots in car seat.
Harness
Safety
Cover
Metal
Rod
Adjuster
Loop
TICS1203e (EN).qxd 4/4/05 4:15 PM Page 23
23
Harness Use and Adjustment
Harness Strap Adjustment:
• To tighten: Pull front adjuster strap (fig. a).
• To loosen: While pressing harness adjuster lever, pull harness
straps out.
Chest Clip Operation:
• To open: Press tabs and pull apart (fig. b).
• To close: Snap halves together. Make sure chest clip is locked
by pulling out.
Carry Handle Operation - Carry handle has three positions (fig. c):
A. Vehicle use position and carrying position
B. Vehicle use position and rocking position
C. Vehicle use position and reclined seat position
Each handle position can be used for vehicle positions depending on size of vehicle.
To change carrying handle position:
• Push in handle buttons on each side of handle (fig. d).
• Rotate handle forward or backward until it locks into the
proper use position.
IMPORTANT: Check to be sure carry handle is locked
before lifting car seat.
(fig. b)
(fig. c)
(fig. d)
Harness
Adjuster
Lever
(Under
Pad)
(fig. a)
Harness
Adjuster
Strap
Handle
Buttons
1
2
1
2
1
2
1
1
2
2
1
1
2
TICS1203e (EN).qxd 4/4/05 4:15 PM Page 24
A
B
C
Base Adjustment:
Turn recline adjustment knob to raise base (fig. a).
Push-in red recline adjustment button at center of recline adjustment knob and turn
knob to lower base.
Infant Insert:
Canopy:
Secure snaps on side of canopy to seat pad, hook canopy over back of car seat and
pull canopy forward (fig. b).
WARNING
• To prevent ejection:
Shoulder belts MUST be through belt slots in infant insert.
- For proper harness fit, infant insert MUST be used for small infants.
• Discontinue use of infant insert when:
- Child’s shoulders are above middle belt slots in seat back of car seat.
- Shoulder belts become too short to fit infant (approximately 5 months of age).
24
(fig. a)
(fig. b)
TICS1203e (EN).qxd 4/4/05 4:15 PM Page 25
25
To provide a secure installation of the car seat:
• Read the vehicle owner’s manual regarding car seat installation and vehicle seat belt use with car seat.
• Follow all instruction labels on vehicle seat belt and car seat.
If car seat does not stay tightly secured after following instructions in this manual, vehicle seat belt labels, and
vehicle owner’s manual:
• Move car seat to another seating location and try again, or
• Contact vehicle dealer for assistance and possible seat belt modification parts.
• Obtain assistance, see “Need Help Installing Your Car Seat” in “Proper Use Checklist” section.
Design and operation of vehicle seat belt systems vary from vehicle to vehicle and from seating location to seating
location in the same vehicle. Not all vehicle seat belts can be used with a child restraint. Refer to the information in
this section for information on the various types of vehicle seat belt systems.
Section 12 - Vehicle Seat Belt Systems
WARNING
DEATH or SERIOUS INJURY can occur
• Not all vehicle seat belts can be used with a car seat. The car seat must be held tight at all times by a lap
belt (or lap belt portion of a lap/shoulder belt) that will not loosen while driving.
TICS1203e (EN).qxd 4/4/05 4:15 PM Page 26
26
Manually adjustable lap belts (fig. c) normally will hold a car seat tightly. However, in some
cases, the locking latch plate on some seat belts may slip and loosen if positioned at a
certain angle. If this happens, flip latch plate over (fig. c) and re-buckle. Test installation
again to see if lap belt stays tight. If not, move car seat to another seating location.
Lap Belts - Manually Adjustable
(fig. c)
Flip
Vehicle seat belts located forward of seat bight (fig. a & b) may not securely
hold car seat. Check vehicle owner’s manual or see vehicle dealer for car seat
installation requirements.
• If seating position is approved for use with car seat, install car seat and
check for secure installation by pulling car seat front to back. If car seat
slides forward or vehicle seat belt does not stay tight, DO NOT use these
seat belts.
Belts Forward of Seat Bight
(fig. a)
Seat
Bight
Belt Forward
of Seat Bight
Buckle
Forward of
Seat Bight
Seat
Bight
(fig. b)
TICS1203e (EN).qxd 4/4/05 4:15 PM Page 27
27
Lap belts with retractors (fig. d) may or may not hold a car seat securely.
Follow these steps to determine if you have a retractor system that will hold car seat securely:
a. Pull belt all the way out.
b. Allow belt to retract about 6 inches (15 cm).
c. Pull out on belt again.
If belt is locked and you cannot pull the belt out any further, you have an Automatic
Locking Retractor which may be used with a car seat. Remember, when installing a
car seat, pull belt all the way out, buckle belt, and then tighten.
If the belt pulls out (step c), the retractor is an Emergency Locking Retractor which must
not be used with a car seat.
Lap Belts - With Retractor
(fig. d)
Lap Belt with Motorized Shoulder Belt
(fig. e)
DO NOT use with any car seat.
Passive Restraints
(fig. e)
Lap or Shoulder Belt Mounted on Front Door
(fig. f)
DO NOT use a car seat in any front seating location that has belts mounted to the
front door. Belts will not stay tight while driving.
(fig. f)
Front
Door
TICS1203e (EN).qxd 4/4/05 4:15 PM Page 28
Section 12 - Vehicle Seat Belt Systems
WARNING
DEATH or SERIOUS INJURY can occur
• Failure to use the belt lock-off where required will result in car seat not being securely held in place.
Belt Lock-off
To secure lap belt with belt lock-off:
Remove the belt lock-off from its storage location on the back of the car seat.
The belt lock-off is attached to the seat pad behind top of seat back.
Install car seat without the base and tighten vehicle seat belt as instructed in
“Securing Infant Car Seat Without Base” section.
Hold vehicle seat belts together at latch plate (fig. c). Release vehicle seat belt
buckle.
Open the belt lock-off and slide over both belts (fig. d), placing
it as close to the latch plate as possible (1/2 inch to 1 inch /
1.3 cm to 2.5 cm maximum). Secure belt lock-off by pivoting
lock tab down onto belt lock-off.
Resecure the vehicle lap belt around the infant car seat.
28
(fig. c)
For use only when securing the infant car seat without the base.
You MUST use the belt lock-off (fig. a) provided to tightly secure the lap belt with a
vehicle lap/shoulder belt that slides freely through the latch plate.
To open the belt lock-off:
- Lift lock tab .
- Lift lock-off tab .
(fig. d)
1/2 inch to 1 inch (1.3 to 2.5 cm)
Lock
Tab
1
2
3
4
(fig. b)
(fig. a)
1
2
1
2
TICS1203e (EN).qxd 4/4/05 4:15 PM Page 29
The vehicle lap belt must be tight around the car seat and must stay tight. Check
for a secure installation - pull front to back and side to side. If the car seat is not
tightly secured, remove the belt lock-off and repeat steps 1 and 2.
If car seat cannot be held tightly, check vehicle owner’s manual, see “Vehicle Seat
Belt” section or move it to another seating location. If there is not a location that
will keep the car seat secured with the lap belt, contact your vehicle dealer to have
a lap belt installed in your vehicle.
To remove the belt lock-off:
Release seat belt buckle.
Pivot lock tab up and open belt lock-off.
29
5
1
2
TICS1203e (EN).qxd 4/4/05 4:15 PM Page 30
30
This child restraint system conforms to all applicable Federal Motor Vehicle Safety Standards for use in motor
vehicles and aircraft.
Certification
DO NOT use after 7 years from date of manufacture on label.
Car Seat Useful Life
Car seat parts can get very hot in the sun or warm weather.
To avoid burns, always check before putting child in car seat.
Warm Weather
Protect vehicle seat. Use a thin car seat mat, thin towel or thin blanket under and behind car seat.
Vehicle Seat Protection
This restraint is Certified for Use in Motor Vehicles and Aircraft (see label on car seat).
Contact airline about their policy on use of child restraints on the Aircraft.
Use this car seat only on forward-facing aircraft seats.
Install car seat on aircraft the same way it is installed in a vehicle.
Aircraft Use
Store instruction manual inside LATCH storage compartment located in lower base.
Instruction Manual Storage
Section 13 - Additional Information
TICS1203e (EN).qxd 4/4/05 4:15 PM Page 31
31
Cleaning Seat:
To Remove Seat Pad:
1. Remove shoulder harness.
2. Slide seat pad from car seat by gently pulling it off the top of car seat back.
To Launder Pad:
1. Machine wash separately in cold water - delicate cycle, no bleach, and drip dry.
To Reassemble Seat Pad:
Reverse above steps for replacing seat pad and harness system.
Cleaning Harness and Crotch Straps:
Surface wash only with mild soap and damp cloth.
If harness straps are frayed or heavily soiled, they MUST be replaced.
Cleaning Shell:
Wipe with mild solution of soap and water. Avoid wetting labels.
Never use “household detergents”: they can weaken plastic.
Cleaning Buckle:
Rinse buckle with warm water. DO NOT use household detergents. Never lubricate buckle.
Section 14 - Care and Cleaning
TICS1203e (EN).qxd 4/4/05 4:15 PM Page 32
32
Child restraints (car seats) could be recalled for safety reasons. You must register this restraint to be reached in a
recall. Fill out the registration card attached to car seat or send your name, address, and the restraint’s model number
and manufacturing date to:
Combi USA
1962 Hwy 160 West, #100
Fort Mill, SC 29708
or call 1-800-992-6624
or fax 1-803-548-3663
or log onto www.combi-intl.com
For recall information:
• Call the U.S Government’s Auto Safety Hotline at 1-800-424-9393 (202-366-0123 in D.C. area)
• Log onto the National Highway Traffic Safety Administration recall website at:
http://www-odi.nhtsa.dot.gov/cars/problems/recalls/childseat.cfm
• Contact Combi USA, Inc. (see contact information above)
Section 15 - Registration Information
TICS1203e (EN).qxd 4/4/05 4:15 PM Page 33
33
TICS1203e (EN).qxd 4/4/05 4:15 PM Page 34
34
TICS1203e (EN).qxd 4/4/05 4:15 PM Page 35
Keep this instruction manual for future use.
Store instruction manual inside LATCH storage
compartment located on front of lower base.
Combi USA • 1962 Hwy 160 West, #100 • Fort Mill, SC 29708 •
Customer Service Telephone 1-800-992-6624 • Se Habla Español 1-803-548-6633 •
Fax 1-803-548-3663 • www.combi-intl.com •
10:00 a.m. - 5:00 p.m. Eastern Time • Monday - Friday
© 2004 Combi USA, Inc. TICS1203e
Designed by Parents, for Parents
TICS1203e (EN).qxd 4/4/05 4:15 PM Page 36
Loading...