Columbia Products Sani-Lav ES2-505L, Sani-Lav ES2-505L-0.5, Sani-Lav ESB2-505L, Sani-Lav ESB2-505L-0.5 Operating Manual

SINKS WITH ELECTRONIC SENSORS

Operating Manual for Hands-Free Wall Mounted Sinks

AC Models ES2-505L and ES2-505L-0.5

Battery Models ESB2-505L and ESB2-505L-0.5

1

AC OR BATTERY POWERED

Columbia does not recommend use with harsh chemicals.

NSF/ANSI Standard 2 - Food Equipment and NSF/ANSI 372 low-lead.

COLUMBIA SPECIFICATIONS

SINKS WITH ELECTRONIC SENSORS

AC OR BATTERY POWERED

2

Parts List

(1) Wall mount sink

(1) AC or Battery powered sensor faucet assembly

(1) Wall-mounting bracket

(2) Support brackets

(1) Mixing check valve

(1) Strainer assembly with basket

Installation Instructions

Step 1

1. Establish sink location on the wall.

2. Determine desired height for the top of the backsplash from finished floor and draw a level
line which will be the top edge of the wall mounting bracket.

3. Hold the wall mounting bracket against the wall and mark the wall where the holes are. Drill
holes and secure bracket to the wall as shown in illustration A. Screws are not provided.

4. Position the sink onto wall bracket.

5. Mark holes for fastening side mounting brackets as shown in illustration B.

6. Remove sink from the wall bracket.

7. Drill holes in wall for securing sink to wall. Screws are not provided.

Step 2

1. Install strainer assembly.

2. Install faucets to the sink following the instructions provided with sensor unit.

3. Attach supply tube with elbow to back of faucet.

4. Install mixing check valve and compression fitting to control box of each sensor faucet.

Step 3

1. Position the sink onto wall bracket and secure to wall.

2. Connect waste line to strainer assembly.

3. Mount sensor control box at desired location on wall.

4. Connect power line from sensor to control box.

5. Attach supply tube from faucet to control box.

6. Connect hot and cold water from the source to mixing check valve.

7. Remove aerator from the spout assemblies and flush water system. (see step 7 sensor
installation instructions)

8. Check connections for leaks.

9. Replace aerator onto the spout.

10. We recommend sealing top of backsplash to wall as shown in illustration C.

Tools Required

Tape Measure

Adjustable Wrench

Drill Motor and Drill Bits

Pipe Wrench

Level

Safety Glasses

Screw Drivers: 1 Phillips & 1 Standard

Pencil

Socket Wrench

Illustration A

Illustration B

Notice for California Consumers

WARNING: This product can expose you to chemicals including Chromium (hexavalent compounds),

Lead, and Phthalates (DEHP) which are known to the State of California to cause cancer and birth defects
or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

NOTE: Lead content originates from Brass components in valves and faucets and is certied under

NSF/ANSI 372 as containing less than 0.25% lead in wetted surfaces.

1622 Browning Irvine, CA 92606-4809 Phone: [phone] Toll Free: 800.626.2117 Fax: [phone] www.columbiasinks.com email: [e-mail]

Illustration C

©2019 Columbia Products

COLUMBIA SPECIFICATIONS

SINKS WITH ELECTRONIC SENSORS

AC OR BATTERY POWERED

3

Top

19” (483mm)
17” (432mm)

5.5” (140 mm)

2” drain hole

Front Side

4” (102 mm)

1.25” R
32mm

17.875” (454mm)

wall hanger

14”

(356mm)

9.5”

(241mm)

7”

(197mm)

2” (51mm)

18”

(457mm)

Hole Configuration

7.5” (191mm)

6.125” (156mm)

45º

16.5”

(419mm)

21”

(533mm)

Stainless Steel Brackets

2” (51mm)

Wall Mounting Detail

1.5” (38mm)

back splash

.25” dia. hole

wall hanger

.875” (22mm)

dia. key hole

9.5”

(241mm)

9.5”

(241mm)

6” (152mm)

9.5” (241mm)

1622 Browning Irvine, CA 92606-4809 Phone: [phone] Toll Free: 800.626.2117 Fax: [phone] www.columbiasinks.com email: [e-mail]

©2019 Columbia Products