Columbia Products SANI-LAV 705A, SANI-LAV 705A-0.5, SANI-LAV 705B, SANI-LAV 705B-0.5 Operating Manual

HANDS-FREE WALL MOUNTED SINKS

AC OR BATTERY POWERED

Operating Manual for Hands-Free Wall Mounted Scrub Sinks

AC Models 705A and 705A-0.5

Battery Models 705B and 705B-0.5

1

Columbia does not recommend use with harsh chemicals.

NSF/ANSI Standard 2 - Food Equipment and NSF/ANSI 372 low-lead.

COLUMBIA SPECIFICATIONS

HANDS-FREE WALL MOUNTED SINKS

AC OR BATTERY POWERED

2

Parts List

(1) Wall mount sink

(1) AC or Battery powered sensor faucet assembly

(1) Wall-mounting bracket

(2) Support brackets with 4 mounting bolts

(1) Mixing check valve

(1) Strainer assembly with basket

Installation Instructions

Step 1

1. Establish sink location on the wall.

2. Determine desired height for the top of the backsplash from finished floor and draw a level
line which will be the top edge of the wall mounting bracket.

3. Hold the wall mounting bracket against the wall and mark the wall where the holes are. Drill
holes and secure bracket to the wall as shown in illustration A. Screws are not provided.

Step 2

1. Install strainer assembly.

2. Install faucets to the sink following the instructions provided with sensor unit.

3. Attach supply tube with elbow to back of faucet.

4. Install mixing check valve and compression fitting to control box of each sensor faucet.

Step 3

1. Position the sink onto wall bracket.

2. Loosely attach support brackets under sink and push against wall then mark holes for
drilling as shown in illustration B.

3. Remove support brackets from sink and drill holes for mounting fasteners (not provided).

4. Re-mount support brackets to sink and fasten to wall.

Step 4

1. Connect waste line to strainer assembly (s).

2. Mount sensor control box at desired location on wall.

3. Connect power line from sensor to control box.

4. Attach supply tube from faucet to control box.

5. Connect hot and cold water from the source to mixing check valve (s).

6. Remove aerator from the spout assemblies and flush water system. (see step 7 sensor
installation instructions)

7. Check connections for leaks.

8. Replace aerator onto the spout (s).

9. We recommend sealing top of backsplash to wall as shown in illustration C.

Tools Required

Tape Measure

Adjustable Wrench

Drill Motor and Drill Bits

Pipe Wrench

Level

Safety Glasses

Screw Drivers: 1 Phillips & 1 Standard

Pencil

Socket Wrench

Illustration A

Illustration B

Notice for California Consumers

WARNING: This product can expose you to chemicals including Chromium (hexavalent compounds),

Lead, and Phthalates (DEHP) which are known to the State of California to cause cancer and birth defects
or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

NOTE: Lead content originates from Brass components in valves and faucets and is certied under

NSF/ANSI 372 as containing less than 0.25% lead in wetted surfaces.

1622 Browning Irvine, CA 92606-4809 Phone: [phone] Toll Free: 800.626.2117 Fax: [phone] www.columbiasinks.com email: [e-mail]

Illustration C

©2019 Columbia Products

COLUMBIA SPECIFICATIONS

HANDS-FREE WALL MOUNTED SINKS

AC OR BATTERY POWERED

3

Top

20in

508mm

2in

50.8mm

2in

R.5in

12.7mm

17in

431.8mm

50.8mm

355.6mm

14in

1.5in

38.1mm

38.1mm

1.5in

444.5mm

17.5in

Front Side

10in

241.3mm

178.9mm

9.5in

254mm

7in

10in

254mm

Wall-mounting

bracket

R.75in

19.1mm

3.25in

100mm

82.6mm

4in

.75in

19.1mm

45deg

7.087in
180mm

Wall Mounting Detail

2” (51mm)

1.5” (38mm)

.25” dia. hole (6mm)

wall hanger

back splash

Hole Configuration

10in

254mm

.875” [22mm]
dia. hole

18.828in

478.2mm

10in

254mm

6.25in

158.8mm

1622 Browning Irvine, CA 92606-4809 Phone: [phone] Toll Free: 800.626.2117 Fax: [phone] www.columbiasinks.com email: [e-mail]

©2019 Columbia Products