Columbia Products 56WAL, 56WAL-1.0, 56WAL-0.5, 56WBL, 56WBL-1.0 Operating Manual

HANDS-FREE WALL MOUNTED WASH STATIONS

AC OR BATTERY POWERED

Operating Manual for Three-Person Hands-Free Wall Mounted Wash Stations

AC Models 56WAL, 56WAL-1.0 and 56WAL-0.5

Battery Models 56WBL, 56WBL-1.0 and 56WBL-0.5

1

Columbia does not recommend use with harsh chemicals.

NSF/ANSI Standard 2 - Food Equipment and NSF/ANSI 372 low-lead.

COLUMBIA SPECIFICATIONS

HANDS-FREE WALL MOUNTED WASH STATIONS

AC OR BATTERY POWERED

2

Parts List

(1) Wall mount wash station

(3) AC or Battery powered sensor faucet assembly

(2) Wall-mounting brackets

(2) Support brackets

(3) Mixing check valve

(1) Strainer assembly with basket

Installation Instructions

Step 1

1. Establish sink location on the wall.

2. Determine desired height for the top of the backsplash from finished floor and draw a level
line which will be the top edge of the wall mounting bracket.

3. Hold the wall mounting bracket against the wall and mark the wall where the holes are. Drill
holes and secure bracket to the wall as shown in illustration A. Screws are not provided.

Step 2

1. Install strainer assembly.

2. Install faucets to the sink following the instructions provided with sensor unit.

3. Attach supply tube with elbow to back of faucet.

4. Install mixing check valve and compression fitting to control box of each sensor faucet.

Step 3

1. Position the sink onto wall bracket.

2. Loosely attach support brackets under sink and push against wall then mark holes for
drilling as shown in illustration B.

3. Remove support brackets from sink and drill holes for mounting fasteners (not provided).

4. Re-mount support brackets to sink and fasten to wall.

Step 4

1. Connect waste line to strainer assembly (s).

2. Mount sensor control box at desired location on wall.

3. Connect power line from sensor to control box.

4. Attach supply tube from faucet to control box.

5. Connect hot and cold water from the source to mixing check valve (s).

6. Remove aerator from the spout assemblies and flush water system. (see step 7 sensor
installation instructions)

7. Check connections for leaks.

8. Replace aerator onto the spout (s).

9. We recommend sealing top of backsplash to wall as shown in illustration C.

Tools Required

Tape Measure

Adjustable Wrench

Drill Motor and Drill Bits

Pipe Wrench

Level

Safety Glasses

Screw Drivers: 1 Phillips & 1 Standard

Pencil

Socket Wrench

Illustration A

Illustration B

1622 Browning Irvine, CA 92606-4809 Phone: [phone] Toll Free: 800.626.2117 Fax: [phone] www.columbiasinks.com email: [e-mail]

Illustration C

©2018 Columbia Products

COLUMBIA SPECIFICATIONS

56 Wall

HANDS-FREE WALL MOUNTED WASH STATIONS

AC OR BATTERY POWERED

3

1.5” (38mm)

.437” (6mm)

.75” (19mm) slot

.437” (6mm)

Top

60” (1524mm)

(267 mm)

57” (1448mm)

30” (762mm)

10.25”

2” drain hole

.5” R

(12.7mm)

30” (762mm)

Front Side

.5” R

(12.7mm)

dia. hole

(407mm)

wall hanger

(254mm)

8” (203mm)

4” (101.6mm)

4” (101.6mm)

2” (51mm)

16.5”

20”

(508mm)

1.5” (38mm)

10”

1.5” (38mm)

35” (889mm)

suggested

floor to rim

height

20” (508mm)

2” (51mm)

7.5” (191mm)

45º

Hole Configurations

11”

(279.4mm)

.875” (22mm)

dia. holes (3)

19”

(482.6mm)

49.5” (1,257.3mm)

19”

(482.6mm)

11”

(279.4mm)

6.75” (171mm)

Wall Mounting Detail

1.5” (38mm)

2” (51mm)

.25” dia. hole

wall hanger

back splash

1622 Browning Irvine, CA 92606-4809 Phone: [phone] Toll Free: 800.626.2117 Fax: [phone] www.columbiasinks.com email: [e-mail]

©2018 Columbia Products