Color imagination CI-039 User Manual

LED

LED Moving

Moving

Moving Head

Head

User

User Manual

Manual

KEEP

KEEP THIS

THIS

THIS MANUAL

MANUAL

MANUAL FOR

FOR

FOR FUTURE

FUTURE

FUTURE NEEDS

NEEDS

1.

1. Dispacking

Dispacking

Thank you for choosing our moving head. For your own safety, please read this

manual before installing the device. This manual covers the important information

on installation and applications. Please install and operate the fixture with following

instructions. Meanwhile, please keep this manual well for future needs.

Color Imagination ’ s moving wash is made of a new type of high temperature

strength of engineering plastics and cast aluminum casing with nice outlook. The

fixture is designed and manufactured strictly following CE standards, complying

with international standard DMX512 protocol. It ’ s available independently

controlled and linkable with each other for operation. And it is applicable for

large-scale live performances, theater, studio, nightclubs and discos.

SI-039 adopts powerful LED lamps which features high brightness and stability.

Please carefully dispack it when you receive the fixture and check whether it is

damaged during the transportation. And please check whether the following items

are included inside the box:

Moving

Moving Head-------

Head-------

Head------- one

one

one Signal

Signal

Signal Cable----one

Cable----one

Omega

Omega Clamp------one

Clamp------one

Clamp------one User

User

User Manual----one

Manual----one

-1-

10.

10. Maintenance

Maintenance

Maintenance and

and

and Cleaning

Cleaning

The following points have to be considered during the inspection:

1) All screws for installing the devices or parts of the device have to be tightly

connected and must not be corroded.

2) There must not be any deformations on the housing, color lenses, fixations and

installation spots (ceiling, suspension, trussing).

3 ） Mechanically moved parts must not show any traces of wearing and must not

rotate with unbalances.

4 ） The electric power supply cables must not show any damage, material fatigue or

sediments.

Further instructions depending on the installation spot and usage have to be adhered

by a skilled installer and any safety problems have to be removed.

In order to make the lights in good condition and extend the life time, we suggest a

regular cleaning to the lights.

1) Clean the inside and outside lens each week to avoid the weakneness of the

lights due to accumulation of dust.

2) Clean the fan each week.

3)Adetailed electric check by approved electrical engineer each three month,

make sure that the circuit contacts are in good condition, prevent the poor

contact of circuit from overheating.

We recommend a frequent cleaning of the device. Please use a moist, lint- free cloth.

Never use alcohol or solvents.

There are no serviceable parts inside the device. Please refer to the instructions

under “ Installation instructions ” .

Should you need any spare parts, please order genuine parts from your

local dealer.

-10-

9.

9. Wave

Wave

Wave Beam

Beam

-9-

2.

2. S

S

S afety

afety

afety I

I

I nstructions

nstructions

This device has left the factory in perfect condition. In order to maintain this condition

and to ensure a safe operation, it is absolutely necessary for the user to follow the

safety instructions and warning notes written in this user manual.

If the device has been exposed to temperature changes due to environmental

changes, do not switch it on immediately. The arising condensation could damage

the device. Leave the device switched off until it has reached room temperature.

This device falls under protection-class I. Therefore it is essential that the device be

earthed.

The electric connection must carry out by qualified person.

The device shall only be used with rate voltage and frequency.

Make sure that the available voltage is not higher than stated at the end of this

manual.

Make sure the power cord is never crimped or damaged by sharp edges. If this would

be the case, replacement of the cable must be done by an authorized dealer.

Always disconnect from the mains, when the device is not in use or before cleaning it.

Only handle the power cord by the plug. Never pull out the plug by tugging the power

cord.

During initial start-up some smoke or smell may arise. This is a normal process and

does not necessarily mean that the device is defective, it should decrease gradually.

Please don't project the beam onto combustible substances.

Fixtures cannot be installed on combustible substances, keep more than 50cm

distance with wall for smooth air flow, so there should be no shelter for fans and

ventilation for heat radiation.

If the external flexible cable or cord of this luminaire is damaged, it shall

be exclusively replaced by the manufacturer or his service agent or a similar qualified

person in order to avoid a hazard

-2-

3.

3. Operation

Operation

Operation Instructions

Instructions

-The moving head is an LED wash light for onsite decoration purpose.

-Don ’ t turn on the fixture if it’s been through severe temperature difference like after transportation because it might damage the light due to the environment changes. So make sure to operate the fixture until it is in normal temperature.

-This light should be keep away from strong shaking during any transportation or movement.

-Don ’ t pull up the light by only the head, or it might cause damages to the mechanical parts.

-Don ’ t expose the fixture in overheat, moisture or environment with too much dust when installing it. And don ’ t lay any power cables on the floor. Or it might cause electronic shock to the people.

-Make sure the installation place is in good safety condition before installing the fixture.

-Make sure to put the safety chain and check whether the screws are screwed properly when installing the fixture.

-Make sure the lens are in good condition. It’s recommended to replace the units if there are any damages or severe scratch.

-Make sure the fixture is operated by qualified personnel who knows the fixture before using.

-Keep the original packages if any second shipment is needed.

-Don ’ t try to change the fixtures without any instruction by the manufacturer or the appointed repairing agencies.

-It is not in warranty range if there are any malfunctions from not following the user manual to operate or any illegal operation, like shock short circuit, electronic shock, lamp broke, etc.

-3-

8.

8. Technical

Technical

Technical Specifications

Specifications

108PCS 1W or 3W high power LEDs 50,000 hours lifespan and low power consumption 8 bit smooth and precise resolution for PAN/TILT movement 540 ° /630 ° pan and 265 ° tilt movement Scan position memory, auto reposition after unexpected movement RGB color mixing system LED shutter LED dimming LED rainbow effect Macros effect Strobe effect with 18 flashes per second and pulse effect General dimming and blackout for all four colors 12 DMX channels DMX512, master-slave and sound activated controllable or auto operation Blue background LCD display

Input Voltage: AC90-260V 50-60Hz LED Quantities:

24 red/2 8 green/2 8 blue/ 2 8 white Edison LEDs (1W )

24 red/2 8 green/2 8 blue/ 2 8 white Edison LEDs (3W) Control Signal: DMX512, master-slave and sound activated or auto operation Control Channel: 12 DMX Channels Power Consumption: 1 5 0 W/ 3 50 W Dimensions: 350x260x350mm Packing Dimensions: 4 4 5x 310 x 435 mm Net Weight: 9 kgs Gross Weight:11kgs

-8-

7.DMX

7.DMX Channels

Channels

Channel Function Value Description

1 Pan 0-540 Pan movement 16 bit

2 Tilt 0-280 Tilt movement 16 bit

3 Dimmer 0-100 G amma adjustment

4

Strobe

000-006 N o function

007-065 S low to fast strobe

066-069 N o function

070-128 Pulse strobe from slow to fast

129-132 N o function

133-191 Strobe fading in from slow to fast

192-195 N o function

196-255 Strobe fading out from slow to fast

5 Red 0-100% Red ( 0-Black , 255-100% Red )

6 Green 0-100% Green ( 0-Black , 255-100% Green )

7 Blue 0-100% Blu e ( 0-Black , 255-100% Blue )

8 White 0-100% White ( 0-Black , 255-100% White )

9 Scan S peed 0-255 From fast to slow

10

RGB macro function

000-004 N o function

005-044 E ight fixed color s

045-049 N o function

050-094 E ight jumping color s (9 levels)

095-099 N o function

100-149 E ight fading color s (5 levels)

150-154 N o function

155-166 R ed+ G reen from dark to b right

167-178 G reen+ R ed from bright to dark

179-190 G reen+ B lue from dark to bright

191-202 B lue+ G reen from bright to dark

203-214 B lue+ R ed from dark to bright

215-226 R ed+ B lue from bright to dark

227-238 RGB from dark to brigh t

239-250 B lue+ R ed from dark to bright at the same time

green from bright to dark

251-255 O u tput 100%at the same time

11

Auto 000-127 N o fuction

128-255 Auto

12 R eset 000-250

251-255

No function

Reset (3 seconds)

-7-

4.

4. Installation

Installation

Installation via

via

via clamp

clamp

Please refer to the picture below:

Screw one clamp each via a M12 screw and nut onto the Omega holders.

Insert the quick-lock fasteners of the first Omega holder into the respective holes on the

bottom of the device. Tighten the quick-lock fasteners fully clockwise. Install the second

Omega holder.

Pull the safety-rope through the holes on the bottom of the base and over the trussing

system or a safe fixation spot. Insert the end in the carabine and tighten the safety screw.

-4-

5.

5. DMX-512

DMX-512

DMX-512 control

control

control connections

connections

Connect the provided XLR cable to the female 3-pin XLR output of your controller and

the other side to the male 3-pin XLR input of the moving head. Y ou can chain multiple

Moving head together through serial linking. The cable needed should be two core,

screened cable with XLR input and output connectors. Please refer to the diagram below.

Address 2 6 Address1 3 Address 1

DMX-512 connection with DMX terminator

For installations where the DMX cable has to run a long distance or is in an electrically

noisy environment, such as in a discotheque, it is recommended to use a DMX terminator.

This helps in preventing corruption of the digital control signal by electrical noise. The

DMX terminator is simply an XLR plug with a 120 Ω resistor connected between pins 2

and 3,which is then plugged into the output XLR socket of the last fixture in the chain.

Please see illustrations below.

1

2

3

PIN 3

PIN 2

120

Ω

-5-

6.

6. LCD

LCD

LCD Display

Display

Display Operations

Operations

The

The display

display

display will

will

will close

close

close after

after

after 30

30

30 seconds

seconds

seconds without

without

without operations.

operations.

-6-