colorFabb XT-CF20 operation manual

Safety datasheet

colorFabb XT-CF20

Safety datasheet conform regulation (EC) 2015/830

Page:

1 of 5

Revision date:

August 17, 2017

Revision:

1.0 Replaces version of:

1. IDENTIFICATION OF THE SUBSTANCE AND THE COMPANY

1.1 Identification of the substance or
preparation:

Colorfabb 3D printing filament
All information in this SDS is applicable to the filament material, not
the filament spool itself.

1.2 Use of the substance or preparation:

FDM 3D printing

1.3 Company/undertaking identification

Colorfabb B.V.
Bremweg 7
NL-5951 DK BELFELD, The Netherlands
Tel.: [phone]
Fax: [phone]
E-mail: [e-mail]

1.4 Emergency telephone:

Colorfabb B.V.; Tel.: [phone] (only during office hours)

2. HAZARDS IDENTIFICATION

2.1 Classification

This product is not classified as dangerous according to Regulation (EC)
1272/2008 (CLP)

2.2 Label elements

Health hazards:

Not applicable

Environmental hazards

Not applicable

Hazard symbol

Not applicable

Signal Word

Not applicable

Hazard Statement

Not applicable

Precautionary statement

Not applicable

PBT and vPvB substances

Not applicable

3. COMPOSITION AND INFORMATION ON INGREDIENTS

3.1 Desciption

colorFabb XT-CF20 is a copolyester, filled with milled carbon fiber
reinforcement and proprietary additivation

3.2 Hazardous ingredients
Substance name

CAS number

Concentration

Classification

H-Phrases

No hazardous
ingredients

---

---

---

---

3.3 Additional information

None

Safety datasheet

colorFabb XT-CF20

Safety datasheet conform regulation (EC) 2015/830

Page:

2 of 5

Revision date:

August 17, 2017

Revision:

1.0 Replaces version of:

4. FIRST AID MEASURES

4.1 Skin contact

Molten material during printing can cause burns. In case of burns cool immediately
with water for at least 10 minutes. Seek medical attention.

4.2 Eye contact

Unlikely during normal use.

4.3 Inhalation

Not likely during normal use. Long term overheating or burning of material can
cause decomposition. After inhalation of decomposition products/fumes, bring the
affected person to a source of fresh air and keep calm, provide medical aid if
necessary.

4.4 Ingestion

Unlikely. If ingestion occurs anyway, drink plenty of water. If difficulties occur, seek
medical attention

4.5 Note to physician

Treat symptomatically.

5. FIRE FIGHTING MEASURES

5.1 Extinguishing media

Dry extinguishing media, foam, water spray or fog

5.2 Extinguishing media not to be used for safety
reasons

5.3 Special hazards arising from the mixture

In case of fire product can decompose and generate
carbondioxide, carbonmonoxide, aldehydes and traces
of other aliphatic and aromatic hydrocarbons

5.4 Protective equipment for fire fighters

Full protective clothing and self-contained breathing
apparatus.

6. ACCIDENTAL RELEASE MEASURES

6.1 Personal precautions

None required; use adequate ventilation during printing

6.2 Environmental precautions

Prevent material ending up in environment

6.3 Cleanup, containment and disposal of spill

Sweep up if needed and dispose

6.4 Reference to other sections

n.a.

7. HANDLING AND STORAGE

7.1 Precautions for safe handling

Avoid contact with heated or molten product during
printing. Ensure adequate ventilation during printing.

7.2 Conditions for safe storage

Store according to instructions. Protect against moisture
and store dry at ambient temperature to maintain
product quality.

7.3 Specific use

Product is meant to be used for FDM 3D printing only.