colorFabb FL6000 operation manual

SAFETY DATA SHEET

Eastman Amphora(TM) Flex 3D Polymer
FL6000

Version

2.0

Revision Date:
08/04/2016

SDS Number:
150000107028

Date of last issue: ­Date of first issue: 08/04/2016

SDSUS / PRD / 0001

Product name

:

Eastman Amphora(TM) Flex 3D Polymer FL6000

Product code

:

000000000050198002

Company name of supplier

:

Eastman Chemical Company

Address

:

200 South Wilcox Drive
Kingsport TN 37660-5280

Telephone

:

[phone]

Recommended use

:

Polymer

Restrictions on use

:

None known.
Combustible dust

Signal word

:

Warning

Hazard statements

:

If small particles are generated during further processing, han­dling or by other means, may form combustible dust concentra­tions in air.

Precautionary statements

:

Disposal:
P501 Dispose of contents/ container to an approved waste dis­posal plant.
Chemical name

CAS-No.

Concentration (% w/w)

polyester

111940-18-2

> 99

additive(s)/colorant(s)

proprietary

< 1

SECTION 1. IDENTIFICATION

Manufacturer or supplier's details

Recommended use of the chemical and restrictions on use

SECTION 2. HAZARDS IDENTIFICATION

GHS Classification

GHS label elements

Other hazards

None known.

SECTION 3. COMPOSITION/INFORMATION ON INGREDIENTS

Components

1 / 9

SAFETY DATA SHEET

Eastman Amphora(TM) Flex 3D Polymer
FL6000

Version

2.0

Revision Date:
08/04/2016

SDS Number:
150000107028

Date of last issue: ­Date of first issue: 08/04/2016

SDSUS / PRD / 0001

If inhaled

:

Move to fresh air.
Treat symptomatically.
If symptoms persist, call a physician.

In case of skin contact

:

Wash off with soap and water.
If symptoms persist, call a physician.
Cool skin rapidly with cold water after contact with molten
material.
Do not peel solidified product off the skin.
Burns must be treated by a physician.

In case of eye contact

:

In the case of contact with eyes, rinse immediately with plenty
of water and seek medical advice.

If swallowed

:

Seek medical advice.

Most important symptoms
and effects, both acute and
delayed

:

The molten product can cause serious burns.
Notes to physician

:

Treat symptomatically.

Suitable extinguishing media

:

Water spray
Dry chemical
Carbon dioxide (CO2)

Unsuitable extinguishing
media

:

Do not use a solid water stream as it may scatter and spread
fire.

Specific hazards during fire­fighting

:

Avoid generating dust; fine dust dispersed in air in sufficient
concentrations, and in the presence of an ignition source is a
potential dust explosion hazard.

Hazardous combustion prod­ucts

:

No hazardous combustion products are known
Further information

:

Minimize dust generation and accumulation.

Special protective equipment
for firefighters

:

Wear an approved positive pressure self-contained breathing
apparatus in addition to standard fire fighting gear.

Personal precautions, protec­tive equipment and emer-

:

Wear appropriate personal protective equipment.
Local authorities should be advised if significant spillages

SECTION 4. FIRST AID MEASURES

SECTION 5. FIREFIGHTING MEASURES

SECTION 6. ACCIDENTAL RELEASE MEASURES

2 / 9

SAFETY DATA SHEET

Eastman Amphora(TM) Flex 3D Polymer
FL6000

Version

2.0

Revision Date:
08/04/2016

SDS Number:
150000107028

Date of last issue: ­Date of first issue: 08/04/2016

SDSUS / PRD / 0001

gency procedures

cannot be contained.

Environmental precautions

:

Avoid release to the environment.

Methods and materials for
containment and cleaning up

:

Sweep up and shovel into suitable containers for disposal.

Advice on protection against
fire and explosion

:

Minimize dust generation and accumulation.

Advice on safe handling

:

Wash thoroughly after handling.
Use only in area provided with appropriate exhaust ventilation.
Minimize dust generation and accumulation.

Conditions for safe storage

:

Keep tightly closed.

Engineering measures

:

Good general ventilation (typically 10 air changes per hour)
should be used. Ventilation rates should be matched to con­ditions. If applicable, use process enclosures, local exhaust
ventilation, or other engineering controls to maintain airborne
levels below recommended exposure limits. If exposure lim­its have not been established, maintain airborne levels to an
acceptable level.

Respiratory protection

:

Use respiratory protection unless adequate local exhaust
ventilation is provided or exposure assessment demonstrates
that exposures are within recommended exposure guidelines.
Wear respiratory protection when its use is identified for cer­tain contributing scenario.

Remarks

:

Wear suitable gloves. When handling hot material, use heat
resistant gloves.

Eye protection

:

Safety glasses
Wear a face shield when working with molten material.

Skin and body protection

:

Wear suitable protective clothing.
Protective measures

:

Ensure that eye flushing systems and safety showers are

SECTION 7. HANDLING AND STORAGE

SECTION 8. EXPOSURE CONTROLS/PERSONAL PROTECTION

Components with workplace control parameters

Contains no substances with occupational exposure limit values.

Personal protective equipment

Hand protection

3 / 9