
H2 PRO ELECT T
INSTALLATION INSTRUCTIONS / CONSIGNES D’INSTALLATION / MONTAGEANLEITUNG
Patent information: | Informations Brevets : | Patentinformation: collingwoodlighting.com/patent
Cut ceiling hole, establish air gap
Découpez le trou d’encastrement et
prévoyez un vide d’air
Connect to mains
Raccordez au secteur
Mit Stromnetz verbinden
Install into ceiling
Installez dans le plafond
In Decke einbauen
Deckenhohlraum öffnen,
Luftzwischenraum sicherstellen
Insulation | Isolation | Isolierung
180mm (min)
100mm (min)
Ø64-72mm
Dimensions shown are achieved using suitable spacer | Dimensions sont atteintes avec l’utilisation d’un capot d’esparement approprié | Angegebene Abmessungen wurden mit geeignetem Abstandhalter erzielt
Loop in/out
Repiquage
Option zum
Durchschleifen
220-240V AC
50/60Hz
IP20
IP20
Fit bezel, twist to lock
Installez la collerette en tournant d’un
quart de tour
Abdeckung mittels Bajonettverschluss
montieren
EN FR DE
Installation data
• Isolate the mains supply, prior to wiring.
• This unit must be wired by a qualified electrician or
suitable competent person.
• Rated voltage 220-240V AC.
• Input current 0.04A.
• For dimming, a dimmer or dimming system suitable for
electronic LED Drivers must be used.
• H2 Pro Elect T is not compatible with auto detect dimming
functions. Auto detect must be switched off or disabled.
• Collingwood Lighting advises the following maximum
loads to assist functionality of the dimming driver when
used with suitable standard mains wall dimmers.
- 5 x units on a 250W dimmer
- 10 x units on a 500W dimmer
- 15 x units on a 1000W dimmer
• For better dimming performance, use dimmers which
have been designed for electronic LED drivers, e.g.
- Varilight V COM 220W – Min 2, max 23 units.
- Legrand Mosaic 078407 - Min 1, max 7 units.
- Legrand Celiane 067083 - Min 1, max 7 units.
• If in doubt, contact the dimmer manufacturer for advice.
Quote the input power of 8.5W, and inrush current of 1.4A
0.4ms.
• The above figures are for guidance only. All installations
must comply with the appropriate standards.
• Input power 8.5W / Power factor 0.95
• Suitable for 30, 60, and 90 minute fire-rated ceilings.
• The light source of this luminaire is not replaceable. When
the light source reaches it’s end of life the whole luminaire
shall be replaced.
Données d’installation
• Avant toute intervention, coupez le courant au disjoncteur.
• Ce produit doit être raccordé par un électricien qualifié ou
une personne compétente appropriée.
• Tension nominale : 220 – 240V AC.
• Courant d’entrée par produit : 0,04A.
• Pour varier l’intensité, un variateur ou un système de
variation compatible avec les alimentations LED doit être
utilisé.
• Le H2 Pro Elect T n’est pas compatible avec une varition à
détection automatique. La détection automatique doit être
éteinte ou débranchée.
• Collingwood Lighting conseille les charges maximales cidessous afin d’assurer la fonctionnalité de l’alimentation
dimmable lorsque celle-ci est utilisée avec un variateur
230V compatible:
- 5 produits par variateur de 250 W
- 10 produits par variateur de 500 W
- 15 produits par variateur de 1000 W
• Pour de meilleures performances en terme de
variation, utilisez un variateur qui a été conçu pour des
alimentations LED, par exemple :
- Varilight V COM 220W: min 2 produits, max 23 produits
- Legrand Mosaic 078407: min 1 produits, max 7 produits
- Legrand Céliane 067083: min 1 produits, max 7 produits
• En cas de doute, contactez le fabricant de variateurs pour
vous renseigner en leur signalant que le produit est de
8,5W et a un courant d’appel de 1.4A 0,4ms.
• Les valeurs ci-dessus sont données à titre indicatif. Toutes
les installations doivent être conformes aux normes en
vigueur.
• Consommation 8,5 W / Facteur de puissance 0,95
• Convient pour des plafonds coupe-feu de 30, 60 et 90
minutes.
• Ce produit est étanche à l’air, il est conforme à une
utilisation dans le cadre de la RT 2012.
• La source de lumière de ce produit n’est pas remplaçable.
Il vous faudra remplacer tout le luminaire une fois sa
durée de vie atteinte.
Montagedaten
• Trennen Sie vor dem Anschluss die Stromversorgung.
• Dieses Gerät darf nur von einer Elektrofachkraft oder
einer entsprechend qualifizierten Person angeschlossen
werden.
• Nennspannungsbereich 220-240 VAC.
• Eingangsstrom 0,04A.
• Zum Dimmen muss ein Dimmer oder Dimmer-System
verwendet werden, welches für elektronische LEDVorschaltgeräte geeignet ist.
• H2 Pro Elect T ist nicht mit automatischer DimmungFunktionen kompatibel. Die automatische DimmungFunktion muss ausgeschaltet oder deaktiviert werden.
• Collingwood Lighting empfiehlt die folgenden maximalen
Belastungen, um die Funktionalität des Treibers
beim Dimmen mit geeigneten, handelsüblichen
Netzspannungs-Wanddimmern zu gewährleisten:
– 5 Leuchten an einem 250W Dimmer
– 10 Leuchten an einem 500W Dimmer
– 15 Leuchten an einem 1000W Dimmer
• Für bessere Dimmleistung benutzen Sie Dimmer, die für
elektronische LED-Treiber konzipiert wurden, z.B.:
- Varilight V COM 220W - Min 2, max. 23 Strahler.
- Legrand Mosaic 078407 - Min 1, max. 7 Strahler.
- Legrand Celiane 067083 - Min 1, max. 7 Strahler.
• Im Zweifelsfall wenden Sie sich an den Hersteller des
Dimmers. Nennen Sie die Eingangsleistung des Strahlers
mit 8,5W und den Einschaltstrom mit 1.4A 0,4ms.
• Die oben genannten Werte sind Richtwerte. Alle Anlagen
müssen den entsprechenden Normen entsprechen.
• Eingangsleistung 8,5W / Leistungsfaktor 0,95
• Geeignet für Brandschutzdecken F30, F60 und F90.
• Die Lichtquelle dieser Leuchte ist nicht austauschbar.
Wenn die Lichtquelle nicht mehr funktionsfähig ist, muss
die komplette Leuchte ersetzt werden.
1 2
Cord grip adaptor / Wired connector
Serre-câble / Reliez les câbles au
bornier de connexion
Die Zugentlastungsklemme /
Verkabelte Anschlussdose
2 x 6242Y
3 x 1.5mm
or | ou | oder
2 x R02V
3 x 1.5mm
EN
t +44 (0) 1604 495 151 f +44 (0) 1604 495 095 e sales@collingwoodgroup.com w collingwoodlighting.com
FR
t +33 (0) 4 816 816 10 f +33 (0) 4 816 816 11 e ventes@collingwoodgroup.com w collingwoodlighting.com
DE
t +49 (0)89 411123 777 f +49 (0)89 411123 778 e verkauf@collingwoodgroup.com w collingwoodlighting.com
Collingwood Lighting, Brooklands House, Sywell Aerodrome, Sywell, Northampton NN6 0BT, United Kingdom
Insert pivot legs into location holes
Insérez les pattes dans les trous
prévus à cet effet
Zapfen in die vorgesehenen
Öffnungen schieben
1
Push firmly to snap shut
Poussez fermement pour refermer
le boîtier
Fest zudrücken, bis Klappe
einrastet
Push here |
Poussez ici |
Hier drücken
2
HLI 1115 V2
To open connector, lever apart
Appuyez pour ouvrir le bornier de
connexion
Zum Öffnen der Anschlussdose Deckel
hochklappen
Lever in here |
Faites effet de levier ici |
Hier hochklappen