Page 1
36mm
250mm
27mm
36mm
Ø50mm
Ø50mm
21mm
250mm
27mm
36mm
250mm
27mm
36mm
Ø50mm
Ø50mm
21mm
250mm
27mm
Salvus Route
Installation instructions
Ø50mm
27mm
250mm
21mm
Ø50mm
36mm
Fig 1.
Baery compartment
LED module
Fig 3.Fig 2.
Disposal of this product should be separate from household waste.
Please separate these items from other types of waste and recycle
them responsibly to promote the sustainable reuse of material
resource. Household users should contact their local government
office for details of where and how they can take these items for
environmentally safe recycling.
Installation
1. Important: This unit must be wired by a qualified electrician or suitable competent person. Isolate the mains supply prior to wiring.
2. Cut an installation hole in ceiling (Ø43mm - Ø44mm) and establish a mains supply to the light fitting.
3. Plug in battery and write commissioning date on battery. To access battery, open battery compartment by unscrewing the 2x screws underneath DC output section (connected to LED
module). Replace battery cover and screws when done. (fig 2).
4. Connect mains input cabling to supplied mains flying lead (L= Brown, N= Blue).
5. Write the installation date in space provided on the product label.
6. Push LED driver and battery into ceiling void. Fold the LED module springs upward and insert into the hole.
Note: Product comes supplied with corridor (160° x 50°) and open area (165°) lenses. To change the lens, twist the lens anticlockwise and pull away (Fig 4). To install the new lens, push the lens
onto the product and twist the lens clockwise. (Fig 5).
7. Turn on mains power. The green LED indicator should be lit indicating that the unit is connected correctly and the battery is charging. Battery will be charged after 24 hours.
4 year warranty
4 ans de garantie
Fig 5.Fig 4.
en
t +44 (0) 1604 495 151 I f +44 (0) 1604 495 095 I e sales@collingwoodgroup.com I w collingwoodlighting.com
Collingwood Lighting, Brooklands House, Sywell Aerodrome, Sywell, Northampton NN6 0BT, United Kingdom
V1
Page 2
Salvus Route
Installation instructions
en
Testing
Periodic testing of the unit must be performed in line with the appropriate regulations.
Emergency pack commissioning (Manual Test Models: EMRWMAN and EMRBMAN)
1. Provide an uninterrupted mains power supply (permanent live) for 24 hours.
2. Check that the green indicator LED light is continuously lit. This confirms that the battery is charging.
3. Remove the mains supply, the unit will operate under battery power for 3 hours minimum.
4. Restore mains power to the unit, check light functions correctly.
5. Pressing the ‘TEST’ button will illuminate the LED for ≈2secs to check LED is functioning.
Emergency pack commissioning (Self Test Models: EMRWST and EMRBST)
1. Provide an uninterrupted mains power supply (permanent live) for 24 hours.
2. Check that the status indicator LED light is continuously lit green. This confirms that the battery is charging.
3. After 24 hours of charging, a duration test is carried out for 3 hours.
Note: After the first duration test, the unit will proceed to perform one duration test between the 300th and 365th day and also check the connection to the battery and LED module.
The status LED change between green and red colours to indicate the current status of the unit as follows:
LED Colour Flashing status Description
Continuously on Baery charging (rst 24hrs aer install), Normal operation
Green
Red
Pressing the ‘TEST’ button will perform different functions depending on press duration as follows:
Slow ash (1 sec on 1 sec o) Duration test in progress
Fast ash (0.2 sec on 0.2 sec o) Function test in progress
Flash 3 times 0.5 sec on 0.5 sec o) Clock reset
Continuously on Baery failure
Slow ash (1 sec on 1 sec o) LED module failure
Fast ash (0.2 sec on 0.2 sec o) Duration failure, the capacity of the baery is insucient
O Product is operating in emergency mode
Press duration Function
Press for < 2 seconds Simulate emergency mode
Press for 3-5 seconds Start duration test manually. Test can be aborted by pressing again for 1-2 sec
Press for 5-8 seconds Start function test manually for 60 sec. Test can be aborted by pressing again for 1-2 sec
Press for >10 seconds Clock reset
Installation data
• Battery must be replaced when the unit no longer meet it’s rated emergency duration, or if a battery fault occurs.
Rated voltage 200 - 240V AC
Input current 0.01A
Power Charging: 1.2W, Charging (baery full): 0.4W, 1W (Emergency mode)
Power factor 0.34
Inrush current 3A
Product weight 180g
Cut-out size Ø43mm - Ø44mm
Disposal of this product should be separate from household waste.
4 year warranty
4 ans de garantie
Please separate these items from other types of waste and recycle
them responsibly to promote the sustainable reuse of material
resource. Household users should contact their local government
office for details of where and how they can take these items for
environmentally safe recycling.
en
t +44 (0) 1604 495 151 I f +44 (0) 1604 495 095 I e sales@collingwoodgroup.com I w collingwoodlighting.com
Collingwood Lighting, Brooklands House, Sywell Aerodrome, Sywell, Northampton NN6 0BT, United Kingdom
V1
Page 3
Salvus Route
Installation instructions
en
Emergency installation and maintenance record Dossier d’installation et service de l’éclairage de sécurité
Product :
Installer :
Date installed :
Commissioning by :
Date commisioned :
Year 1 Year 2 Year 3 Year 4
Month Signed Date Signed Date Signed Date Signed Date
1
2
3
4
5
6
7
8
9
10
11
12
Disposal of this product should be separate from household waste.
4 year warranty
4 ans de garantie
en
t +44 (0) 1604 495 151 I f +44 (0) 1604 495 095 I e sales@collingwoodgroup.com I w collingwoodlighting.com
Collingwood Lighting, Brooklands House, Sywell Aerodrome, Sywell, Northampton NN6 0BT, United Kingdom
Please separate these items from other types of waste and recycle
them responsibly to promote the sustainable reuse of material
resource. Household users should contact their local government
office for details of where and how they can take these items for
environmentally safe recycling.
V1
Loading...