Page 1
Salvus MAX
N
L
N
L
Non-maintained emergency bulkhead
Installation instructions
Security cable
Fig 1.
Jumper Switch-L - 1000lm Jumper Switch-H - 1500lm
220-240V AC - 50/60 Hz
Connect power supply to LED board
Fig 2.
Security cable
Connect power supply to LED boardConnect baery to connector
Disposal of this product should be separate from household waste. Please separate these items
from other types of waste and recycle them responsibly to promote the sustainable reuse of
material resource. Household users should contact their local government office for details of
where and how they can take these items for environmentally safe recycling.
Fig 3.
Cable entry A
Cable entry B
M20 Drill
Cable entry
M20 Drill
Cable entry
Fig 4.
5 year warranty
en
t +44 (0) 1604 495 151 I f +44 (0) 1604 495 095 I e sales@collingwoodgroup.com I w collingwoodlighting.com
Collingwood Lighting, Brooklands House, Sywell Aerodrome, Sywell, Northampton NN6 0BT, United Kingdom
Replaceable light source
by a professional
Replaceable control gear
by a professional
V1
Page 2
Salvus MAX
Non-maintained emergency bulkhead
Installation instructions
en
Installation
1. This product is manual test.
2. Important: This unit must be wired by a qualified electrician or suitable competent person. Isolate the mains supply prior to wiring.
3. Remove front cover, screws will be loose for ease of install (Fig 1).
4. Screw the back section of the light fitting, onto the mounting surface using the 4x screws provided, taking care to include one of the 4x supplied grommets between the back surface of the
product and the mounting surface at each screw (Fig 4).
5. If using the supplied wall plugs, drill Ø 4mm holes (Fig 4).
6. Feed the mains cabling into the product via the cable entry drill out holes (use M20 drill bit) either on the back or side of the product (Fig 4).
7. Ensure glands are fitted to maintain IP rating (Fig 4).
8. Connect the mains supply to the terminal block on the back plate. L = permanent live, N = neutral, E = earth.
9. Position the jumper switch to the required lumen output (Fig 2).
10. Attach the security cable (Fig 1).
11. Connect power supply to LED board (Fig 3).
12. Connect the battery to the PCB and write commissioning date on the battery (Fig 3).
13. Secure the cover to the body via the 4 captive screws.
14. Turn on mains power. The green LED indicator should be lit indicating the unit is connected correctly and the battery is charging
Emergency pack commissioning
1. Provide an uninterrupted mains power supply (permanent live) for 24 hours.
2. Check that the green indicator LED light is lit. This confirms that the batteries are charging.
3. Remove the mains supply, the unit will operate under battery power for 3 hours minimum.
4. Restore mains power to the unit, check light functions correctly.
Testing
• Periodic testing of the unit must be performed in line with the appropriate regulations.
LED Indicator
• Green constantly lit – normal standby mode or battery is charging.
• Off – emergency mode, battery or light source fault.
Installation data
• Important: This unit must be wired by a qualified electrician or suitable competent person. Isolate the mains supply prior to wiring.
• The light source contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similar qualified person.
• The driver contained in this luminaire shall only be replaced by the manufacturer or service agent or a similar qualified person.
• Battery must be replaced when the unit no longer meet it’s rated emergency duration, or if a battery fault occurs.
Lumen Output 1000lm 1500lm
Input voltage 220 - 240V AC 50/60Hz 220 - 240V AC 50/60Hz
Input current 55mA 55mA
Input power 4.5W 4.5W
Inrush current 12.8A 0.1ms 12.8A 0.1ms
Disposal of this product should be separate from household waste. Please separate these items
from other types of waste and recycle them responsibly to promote the sustainable reuse of
material resource. Household users should contact their local government office for details of
where and how they can take these items for environmentally safe recycling.
5 year warranty
en
t +44 (0) 1604 495 151 I f +44 (0) 1604 495 095 I e sales@collingwoodgroup.com I w collingwoodlighting.com
Collingwood Lighting, Brooklands House, Sywell Aerodrome, Sywell, Northampton NN6 0BT, United Kingdom
Replaceable light source
by a professional
Replaceable control gear
by a professional
V1
Page 3
Salvus MAX
Non-maintained emergency bulkhead
Installation instructions
en
Emergency installation and maintenance record
Product :
Installer :
Date installed :
Commissioning by :
Date commisioned :
Year 1 Year 2 Year 3 Year 4
Month Signed Date Signed Date Signed Date Signed Date
1
2
3
4
5
6
7
8
9
10
11
12
5 year warranty
en
t +44 (0) 1604 495 151 I f +44 (0) 1604 495 095 I e sales@collingwoodgroup.com I w collingwoodlighting.com
Collingwood Lighting, Brooklands House, Sywell Aerodrome, Sywell, Northampton NN6 0BT, United Kingdom
Replaceable light source
by a professional
Replaceable control gear
by a professional
V1
Loading...