Cole-Parmer PT-T-353, PT-T-2002, PT-T-4502, PT-T-753, PT-T-6002 Quick Start Guide

Start up Guide

PA-T and PT-T

Advanced Series Balances

To view a complete user manual
scan QR code.

1. CONTENT

Models: PA-T-225

Balance

x 1

Models: PA-T-124 | PA-T-224

Balance

x 1

Models: PT-T-353 | PT-T-753

Balance

x 1

Weighing pan

x 1

Weighing pan

x 1

Weighing pan

x 1

Draft shield

x 1

Draft shield

x 1

Draft shield

x 1

Centring ring

x 1

Bottom insert

x 1

Grounding foot

x 1

Bottom insert

x 1

Power adapter

x 1

Foot

x 3

Power adapter

x 1

Power adapter

x 1

Models: PT-T-802 | PT-T-2002 | PT-T-4502

Balance

x 1

Models: PT-T-6002

Balance

x 1

Weighing pan

x 1

Weighing pan

x 1

Grounding foot

Draft shield

x 1

x 1

Foot

x 3

Grounding foot

x 1

Power adapter

x 1

Foot

x 1

Power adapter

x 1

2. WORKROOM AND BASIC OPERATION GUIDELINES

o

C

+40
+104oF

o

+10

C

o

F

+50

Place the balance away from heat
sources. Avoid exposing the balance
to the sunlight.

Operate the device in a room where the temperature ranges between 10–40 °C
(50–104 °F) and where the relative humidity is below 80%.

Place the balance on a solid surface to ensure stability. To obtain stable and
repeatable weighing results, an anti-vibration table is recommended.

Avoid exposing the balance to a
magnetic field.Do not weigh magnetic
substances.

Do not place the balance in a hazardous
area. Do not weigh explosive materials.

Avoid air drafts and air movements
at the workstation.

Make sure that the balance is placed
on an even surface.

Do not place the balance on an unstable
ground exposed to shocks and vibrations.

3. UNPACKING

1 2 3

TOP

Keep the packaging should a warranty
claim or service be required.

4. ACTIVITIES TO BE DONE PRIOR TO OPERATION

4.1. Remove transport lock

Models: BA-T-64 | BA-T-124 | BA-T-214

1

Models: BT-T-203 | BT-T-403 | BT-T-503 | BT-T-802 | BT-T-2002 | BT-T-4002 | BT-T-6001 | BTT-10001
BT-T-20001

2

Keep the transport
lock should a
warranty claim or
service be required.

1 2

Keep the transport
lock should a
warranty claim or
service be required.

4.2. Grounding spring check

Models: BA-T-64 | BA-T-124 | BA-T-214

Check the grounding spring.
Make sure that the grounding
spring juts slightly out of the
hole.

Models: BT-T-203 | BT-T-403 | BT-T-503 | BT-T-802 | BT-T-2002 | BT-T-4002 | BT-T-6001 | BTT-10001
BT-T-20001

Check the grounding spring.
Make sure that the grounding
spring juts slightly out of the
hole.

Grounding foot

5. COMPONENTS ASSEMBLY

Models: PA-T-225

1

Models: PA-T-124 | PA-T-224

2

1 2 3

3

4

Models: PT-T-353 | PT-T-753

1 2 3

Install the

grounding foot in

a freely selected

opening.

Models: PT-T-802 | PT-T-2002 | PT-T-4502

1 2

Install the

grounding foot in

a freely selected

opening.

Models: PT-T-6002

1 2 3

grounding foot in

Install the

a freely selected

opening.

6. PREPARING FOR WORK

Ethern

6.1. Balance temperature stabilization time

Prior to switching the device on it is necessary
to ensure that it has reached a temperature

Balance temperature stabilization time ranges
between 1 - 8 hours.

equal to room temperature.

B 2

S

U

BUS 1

Connect the power adapter to DC connector. Connect the power adapter to the mains.

To level the balance, turn its feet and keep
turning the feet until the air bubble takes
the central position.

7. PANEL AND SCREEN

7.1. Panel keys

Proximity sensorProximity sensor

Enteringbalance

setup

Displaying previous

screen

Taring

7.2. Home screen

Working modes list

Switching on / off

Confirming an operation
or printing a report

Zeroing

List of current working
mode functions

Weighing result window

Editable tool bar with quick

access keys

Parameters Header

Adjustment Tare UnitsUnits Operators

printout

Footer

printout

Status bar

Editable information fields
(labels, text fields and buttons)

Databa-

database

ses

8. BASIC OPERATIONS

8.1. Adjustment

1

Press "Adjustment" button.

8.2. Zeroing

2

Wait for the process completion.

21

Unload the weighing pan and press
"Zeroing" button.

8.3. Taring

The balance has been zeroed.

21

When the weighing result has been displayed
press "Tare" button.

The balance has been tared.

8.4. Working modes / units selection

Press the pictogram to view list of all
available working modes.

Working modes list:

Weighing
Dosing
Checkweighing
Formulas
Percent weighing
Statistics

Parts counting
Animal weighing
Solids density
Liquids density
Peak hold

9. SETTINGS

Some balance settings are accessible for Administrator exclusively.
Prior balance parameters setup, log in as the Administrator.

9.1. Administrator's login

Press the pictogram to view

list of all available units.

Units list:

g
mg
ct
lb
oz
ozt
dwt

tlh
tls
tlt
tlc
mom
gr
ti

N
b
aht
tola
msg
u1
u2

1

Press "Operators" button.

3

Press 123 button to activate numeric keyboard. Enter
"1111" password and press button to confirm.

2

Users list is displayed, select Admin option.

4

You have logged in the administrator.

9.2. User settings

Prior balance users setup, log in as the Administrator.

Press "Databases" button. Select Operator database.

21

43

Press "Add" button. Select "Name" parameter.

65

Enter user name. User name has been entered.

Following the above procedure, set remaining parameters:

7

Code:

Enter user ID

Password:

Enter user password

Access levels:

Set respective access level (user, advanced, admin)

9.3. Proximity sensors setup

Prior proximity sensors setup, log in as the Administrator.

You can assign the proximity sensors with different functions for each working mode (the sensors will trigger
different operation for each working mode). The diagram presents sensors setup for the weighing mode.

1 2

Press "Parameters" button.

3 4

Select Weighing parameter.

5

6

Parameters list is displayed, select
Working Modes parameter.

Select Proximity Sensors parameter.

Select Right Sensor parameter. Select function that is to be assigned to the

right proximity sensor.

In order to set left sensor function repeat steps 5 and 6, this time select Left Sensor parameter. Following the
above procedure you can also set sensors for remaining working modes.

10. PERIPHERAL DEVICES CONNECTORS

Power adapter

DC

Computer Printer

Additional

display

Barcode

scanner

DB9

RS 232 RS 232

USB 1 USB 2 Ethernet

Computer Printer

Additional

Barcode scanner

display

DB9

USB

Computer

Barcode

scanner

USB

Keyboard

Printer

Ethernet

USB-A RJ45USB-B

Computer Printer

11. DEVICE CLEANING

11.1. General Recommendations

Prior to cleaning, it is necessary to
disconnect th e balance from the mains.

Avoid using cleansers containing chlorine, corrosive chemicals and bleach. Do not use
cleansers containing abrasive substances or scouring preparations.

Use soft cloths made of microfiber,
natural fiber or man-made fiber. Avoid
using abrasive cloths or cloths that might
scratch the surface.

11.2. Glass components

Prior to cleaning the glass panes, it is necessary to disassemble them first.
For detailed instruction on panes disassembly, refer to user manual.

Clean glass components using a solution of water and detergent (liquid soap,
dish-washing detergent, glass cleaner, etc.). In case of heavy contamination,
a mild solution of vinegar or baking soda can be used.

Apply the cleanser onto the cloth first.
Avoid applying the cleanser directly
onto the device.

11.3. Plastic components

Prior to cleaning the plastic housing, it is necessary to disassemble
weighing pan components (cover, weighing pan, etc.).

Clean plastic components using a solution of water and detergent
(liquid soap, dish-washing detergent, glass cleaner, etc.).

11.4. Stainless steel components

Prior to cleaning the stainless steel components, it is necessary
to disassemble them first.

Clean stainless steel components using a solution of water and detergent
(liquid soap, dish-washing detergent, glass cleaner, etc.). In case of heavy
contamination, a mild solution of vinegar or baking soda. can be used.

625 East Bunker Court Vernon Hills
IL 60061 USA
Phone: [phone]
Fax: [phone]
E-Mail: [e-mail]