Coleman WHITE PINE User Manual
16'X13' WHITE PINE™with SCREEN ROOM
1
Layout & Positioning of Tent
–Layout and position tent with screen room
facing desired direction. (illus. 1)
–Stake down tent corners. Do not stretch
too tight. Angle the stakes slightly toward
the tent. (illus. 2) Keep the floor taut.
–Stake down the remainder of the
stake loops and unzip doors.
–Assemble main tent poles (black)
and side tent poles (gray) by interlocking
the shock-corded sections.
–Insert the main tent poles (black) diagonally
through the pole sleeves.This will form an
“X” in the center of the tent. (illus. 1)
–Insert side tent poles (gray) through the pole
sleeves at the ends of the tent.(illus 1)
When You Are Ready To Set
Up Y our Tent
–Select a level campsite clear of
rocks, branches and other hard
or sharp objects.
–Do not set up your tent
under trees.
–For best results in windy
conditions, position the end of
tent into the wind.
–See owners manual for more tips.
Main Tent Poles
Part No. 9271-166
Side Tent Poles
Part No. 9271-167
Screen Room Ridge Pole
Part No. 9271-162
Screen Room Upright Pole
Part No. 9271-168
Rainfly Part No. 9271-164
Rainfly Pole
Part No. 9271-161
Instructions apply to Part Number 9271-163
Illus. 2
Stake loops
properly staked
Front of
Screen Door
Main poles through pole sleeves
Illus. 1
Chain shock-corded
POLE ASSEMBLY PARTS
Connect Frame to Tent
–Insert one end of main tent pole end onto pin of pin &
ring system, nearest the middle of the tent. (illus. 3, 4)
–Go to opposite end of pole and gradually apply
pressure to the pole forming an arch until you are
able to insert the pin into the pole. (illus. 3, 4)
–Repeat for second pole.
–Insert one end of side tent pole end onto pin of
pin & ring system, at the corner of the tent. (illus. 3)
–Go to opposite end of pole and gradually apply
pressure to the pole forming an arch until you
are able to insert the pin into the pole.
–Repeat for second pole.
–Attach frame clips on the tent tent to frame poles.
(illus. 3, & 5)
2
illus. 5
Frame clips
illus. 3 Tent shown with
main and side tent poles in
place.
illus. 4
Pin & ring system located
on the front & rear of tent
Side tent
pole
3
Raise Screen Room
–Assemble all chain shock-corded
Roof Pole. When assembled will
form a continuous arch with both
ends pointing down. (illus. 6)
–Insert square end of upright poles into
curved roof poles and raise tent upright.
(illus. 7 & 8)
–Angle screen room upright pole back
toward tent body and insert pin of
pin & ring system into end of pole.
–Repeat for second pole.(illus 7)
Pin inserted into
screen room upright pole
4
illus. 8
Curved ridge pole
attaches to
upright pole
illus. 7
Tent shown
without rainfly
illus. 11 Tent shown completed.
Attach Rainfly
–Assemble rainfly pole by interlocking
shock-corded pole.
–Insert rainfly pole into reinforced pockets
located at the center edges of the
underside of rainfly. (illus. 9 & 10)
–Tie underside of rainfly to the rainfly
pole with pole ties. (illus. 9)
–Drape rainfly over tent frame, pole side
down. Rainfly pole should point out over
screen room and rear window of tent.
–Connect the eight elastic loops with
“S” hooks, (found at the rainfly corners)
to the eight rings located at the end of
the stake loops at the corners of the tent.
–Secure rainfly with frame ties
located on underside of rainfly. (illus. 11)
–Stake out tent with four side
guylines. (illus. 11)
Brace Pole
Curved
poles in
pole sleeve
Underside frame
ties attach to tent
poles
THE COLEMAN CO., INC.
3600 N. Hydraulic • Wichita, Kansas 67219
1-800-835-3278 • www.coleman.com
MADE IN SRI LANKA
PRINTED IN SRI LANKA Rev. 11/00
Things You Should Know
•
Under certain conditions (cold weather, high humidity, etc.)
condensation will form on the inside surfaces of your tent.
Condensation is caused by water vapor from your breath, perspiration, or any wet clothing inside your tent.It is NOT LEAKAGE
through the tent fabric. It can be minimized by removing wet clothing
from your tent and by providing good ventilation through the tent.
•
Never store tent, even for a short period of time, without drying it
thoroughly and brushing off caked dirt. Do not pack stakes or poles
inside your tent. Use separate storage bag.
•
STAKES SHOULD BE REMOVED BY PULLING ON THE STAKE
ITSELF. NEVER PULL ON THE TENT FABRIC OR TENT STAKE
LOOP TO REMOVE STAKE.
•
TENT POLES SHOULD NOT BE LEFT TELESCOPED
TOGETHER DURING STORAGE.
•
Seam sealer has not been provided with your tent.It is necessary
and we recommend seam sealing your tent prior to camping. Seam
sealer may be purchased through your local retailer or at your
local sporting goods store.
•
Do not leave your tent set-up for weeks at a time, be aware that
exposure to the ultraviolet rays of the sun can seriously damage
nylon material and/or cause it to become discolored.
WARNING: KEEP ALL FLAME AND HEA T SOURCES
AWAY FROM THIS TENT FABRIC. This tent meets the flamma-
bility requirements of CPAI-84.The fabric will burn left in continuous
contact with any flame source.The application of any foreign substance
to the tent fabric may render the flame-resistant properties ineffective.
Illus. 6 Curved Roof
Pole assembly.
Screen ridge pole sleeve
Forms an arch
illus. 9 Insert
Rainfly Pole
piece into
pocket on
underside of
Rainfly
Frame ties
Pole ties
illus. 10
Underside of rainfly
shown with pole inserted
into pole pockets
Guylines
Loading...