Coleman TYL X2 User Manual

POLE ASSEMBLY PARTS

™

Tyl

part number 9830-261

Main Tent Poles (Silver)

Part No. 9830-1131

Brow Pole

Part No. 9830-1231

Layout & Positioning

of Tent, Pole Assembly

– Layout and position tent with door facing

desired direction. (illus. 1)

– For best results in windy conditions, position

door or back of tent into the wind. – Unzip door. – Stake down tent corners. Keep the floor

taut. (illus. 2)

– Assemble Frame Poles by interlocking the

shock-corded sections. This will make two long silver poles.

– Lay the poles out diagonally, centered on the

tent.The center of the poles should cross forming an “X” in the middle of tent. (illus. 1)

– Fasten toggle & loop on top of tent over both

poles. (illus. 1), (illus. 3)

Rainfly

Part No. 9830-1331

Attach center of the tent to the poles

Toggle & Loop

illus. 1

illus. 2

Tent stake

through Loop

Connect Frame to Tent

– Insert one pole tip into the grommet on the

webbing located at the corners of the tent (illus. 4).

– Go to opposite end of the same pole and

gradually apply pressure to the pole, forming an arch, until you are able to insert the pole tip into the grommet.

– Repeat for second pole.

illus.4

t Pole T

Inser stake loop into pole.

alon on

illus. 5 Tent frame up

illus. 3

oggle & Loop

Attach Tent to Frame Using Frame Clips Add Brow Pole

– Attach frame clips along the edges of

tent to frame poles. (illus. 6), (illus. 7)

– Assembled Brow Pole by interlocking

shock corded sections.

– Insert Brow Pole into the grommets

on the pole clips above the door. (illus. 7)

– Connect the two frame clips above

the door to the Brow Pole. (illus. 7)

– Make any adjustments to the tent

corner stakes that are needed.

Attach Rainfly

– Drape Rainfly over tent frame, with

vestibule area over front door. (illus. 8)

– Connect the four clips (found at the

Rainfly corners) to the clips located at

the corners of the tent. (illus. 9) – Stake out vestibule and rainfly sides. – Secure Rainfly with Frame Ties located

on underside of fly to Gold Brow Pole.

(illus. 10) – Attach Guy Lines to Guy Wing on the

sides of the Rainfly and stake out

(illus.10).

ow Pole

Grommets

illus. 7

Assembled tent without Rainfly. Note the frame clips located on edge of tent.

illus. 8

illus. 10

Completed tent with Rainfly.

illus. 6

Frame Clips

Frame Ties

Guy Line

illus. 9

Rainfly clips onto pole stake loop

Things You Should Know

Under certain conditions (cold weather, high humidity, etc.) condensation will form on the inside surfaces of your tent. Condensation

•

is caused by water vapor from your breath, perspiration, or any wet clothing inside your tent. It is NOT LEAKAGE through the tent fabric. It can be minimized by removing wet clothing from your tent and by providing good ventilation through the tent.

Never stor

•

drying it thoroughly and brushing off caked dirt. Do not pack stakes or poles inside your tent. Use separate storage bag.

AKES SHOULD BE REMOVED BY PULLING ON THE ST

•

ITSELF. NEVER PULL ON THE TENT FABRIC OR TENT STAKE LOOP TO REMOVE STAKE.

TENT POLES SHOULD NOT BE LEFT TELESCOPED TOGETHER

•

DURING STORAGE.

PRINTED IN CHINA

2005

e tent, even for a short period of time, without

AKE

3600 N. Hydraulic • Wichita, Kansas 67219

1-800-835-3278 • www.coleman.com