Coleman FlowClear 90355E Owner's Manual
#90355E
FlowClear
Owner’s Manual
www.bestwaycorp.com
TM
Sand Filter
DO NOT RETURN THIS ITEM TO THE STORE
OR WEBSITE WHERE IT WAS PURCHASED.
CONTACT US DIRECTLY WITH ANY QUESTIONS,
OR FOR DEFECTIVE OR WARRANTY CLAIMS.
CALL US DIRECTLY FOR IMMEDIATE HELP!
Toll-Free: 1-855-838-3888
S-S-005018
SAFETY INSTRUCTIONS
WARNING
IMPORTANT SAFETY INSTRUCTIONS
When installing and using this electrical equipment, basic safety precautions should always be followed, including the following:
READ AND FOLLOW ALL INSTRUCTIONS
WARNING - TO REDUCE THE RISK OF INJURY, do not permit children to use this product unless they are
closely supervised at all times.
WARNING - RISK OF ELECTRIC SHOCK - Connect only to a grounding type receptacle. This product is provided
with a ground-fault circuit-interrupter. If replacement of the plug is needed, use only identical replacement parts.
WARNING - The unit is provided with a ground-fault circuit-interrupter (GFCI). To test the GFCI, push the test button.
The GFCI should interrupt power. Push the reset button. Power should be restored. If the GFCI fails to operate in this manner, the
GFCI is defective. If the GFCI interrupts power to the pump without the test button being pushed, a ground current is flowing,
indicating the possibility of an electric shock. Do not use this pump. Disconnect the pump and have the problem corrected by a
qualified service representative before using.
CAUTION - To reduce the risk of electric shock the pool must be installed no closer than 6 feet (1.8 m) from any
electrical outlet. Do not place portable appliances closer than 5 feet (1.5 m) from the pool.
DO NOT BURY CORD. Locate cord to minimize abuse from lawn mowers, hedge trimmers, and other equipment.
WARNING - To reduce the risk of electric shock, replace damaged cord immediately.
WARNING - To reduce the risk of electric shock, do not use extension cord to connect unit to electric supply; provide a
properly located outlet.
CAUTION: This pump is for use with storable pools only. Do not use with permanently-installed pools. A storable pool is
constructed so that it is capable of being readily disassembled for storage and reassembled to its original integrity. A
permanently-installed pool is constructed in or on the ground or in a building such that it cannot be readily disassembled for storage.
Please examine and verify all sand filter components are present before use. Notify Coleman at the customer service address listed
on this manual for any damaged or missing parts at the time of purchase.
• THERMALLY PROTECTED MOTOR. CSA ENCLOSURE 3
• FOR USE WITH SWIMMING POOLS ONLY.
• CAUTION: TO ENSURE CONTINUED PROTECTION AGAINST SHOCK HAZARD, USE ONLY IDENTICAL
REPLACEMENT PARTS WHEN SERVICING.
• WARNING: RISK OF ELECTRIC SHOCK. CONNECT ONLY TO A GROUNDING TYPE RECEPTACLE.
• CAUTION: THIS PUMP IS FOR USE WITH STORABLE POOLS ONLY - DO NOT USE WITH
PERMANENTLY-INSTALLED POOLS.
• CAUTION: CONNECT ONLY TO GROUNDING TYPE RECEPTACLE PROTECTED BY A CLASS A GROUND
FAULT CIRCUIT INTERRUPTER.
•
CAUTION: FOR CONTINUED PROTECTION AGAINST POSSIBLE ELECTRIC SHOCK THIS UNIT IS TO BE
MOUNTED TO THE BASE IN ACCORDANCE WITH THE INSTALLATION INSTRUCTIONS.
• WARNING – RISK OF ELECTROCUTION
1) Connect Only To Properly Grounded Outlet. Do Not Remove Ground Pin
2) Inspect Cord Before Using – Do Not Use If Cord Is Damaged.
3) Keep Ground-Fault Circuit-Interrupter Dry And Off The Ground.
4) Do Not Touch Plug With Wet Hands
5) Double Insulated – When Servicing Use Only Identical Replacement Parts.
6) Read Instruction Manual Before Using.
DO NOT REMOVE THIS TAG.
SAVE THESE INSTRUCTIONS.
2
S-S-005018
SPECIFICATIONS
Filter Diameter:
Effective Fiter Area:
Max. Operating Pressure:
Working sand filter pressure:
437mm
0.150m
1.58Bar(23PSI)
<0.56Bar(8PSI)
690mm
437mm
633mm
Max. Water Temperature:
Sand:
Sand Size:
Sand Capacity:
35°C
Not included
#20 silica sand, 0.45-0.85mm
Approximately 35 kg
PARTS REFERENCE OVERVIEW
Before assembling the sand filter, take a few minutes to become familiar with all the sand filter parts.
1
2
11
12
13
26
A
21
2
(1.61ft2)
X3
3
14
22
B
B
A
B
X1
X2
4
15
REF.NO SPARE PART NO.
1 P61204
5
16
23
6
17
2 P61138
3 P61205
4 P61209
5 P61213
6 P61206
7 P61211
8 P6581
7
8
18
19
12
9
12
10
20
9 P6580
10 P61212
11 P6614
12 P6029
13 P6540
14 P6560
15 P61214
16 P6561
17 P6562
29
18 P61210
19 P6563
20 P61494
21 P6916
12
2222 27 27
22
22
24
22 P6124
23 P6517
24
P6680
P61318
25 P61408
P6680
P61318
26 P6615
27 P6005
2528 28
28 P6019
29 P6783
3
A
B
1
1
1
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
6
6
1
1
1
1
1
1
1
1
1
1
8
8
1
1
1
1
2
2
5
4
2
2
2
2
1
0
1
1
1
1
2
2
2
2
1
1
S-S-005018
Assembly (You will need a screwdriver).
1. Carefully remove all components from the package and check to ensure nothing is damaged. If
equipment is damaged, immediately notify the retailer from where the equipment was purchased.
2. The sand filter should be placed on solid, level ground, preferably a concrete slab. Position the sand
filter so the Ports and Control Valve are accessible for operation, servicing and winterizing.
3. The sand filter to be vertically fixed on ground or a certain pedestal made of wood or concrete before
use to prevent the sand filter from accidentally falling. Fully assembled sand filter will exceed 35kg. The
mounting holes should be 8mm in diameter and spaced 86mm apart. Use two bolts and nuts with a
maximum of 8mm in diameter to fasten the sand filter to the pedestal.
Ф8mm
86mm
Load pool-grade filter sand.
NOTE: Use only special pool-grade filter sand, free of all limestone or clay: #20 Silica sand 0.45-0.85mm, approximately one
35kg bag should suffice.
If you do not use the recommended size of filter sand, filtering performance will be reduced and the sand filter may damaged, thereby
voiding the warranty.
NOTE: To avoid damaging the Skimmer when adding sand, pour some water into the Bottom Tank to submerse the Skimmer on
the Hub.
NOTE: SAND NOT INCLUDED.
#20
0.45-0.85mm
Connect to the pool
1
4
MAX
MIN
MAX.
MIN .
C
C
C
A
B
A
B
A
B
B
A
B
4
S-S-005018
Loading...