Coleman FC9M060B12UP11, FC9M080B12UP11, FC9M080C16UP11, FC9M100C16UP11, FC9M100C20UP11 Technical Manual

259720-CTG-B-0108

DESCRIPTION

These Category IV, highly efficient, compact, condensing
type furnaces are designed for residential and commercial
installations in a basement, closet, alcove, recreation room or
garage where the ambient temperature is above 32°F, or
higher. They may be either side wall or thru-roof vented using
approved plastic type combustion air and vent piping. All
units are factory assembled, wired and tested to assure
dependable and economical installation and operation.

TECHNICAL GUIDE

Echelon
MODELS: FC9M*UP

GAS-FIRED
CONDENSING / HIGH EFFICIENCY
UPFLOW MODULATING FURNACES

NATURAL GAS
60 - 120 MBH INPUT

EFFICIENCY
RATING
CERTIFIED

ISO 9001

Certified Quality

Management System

Due to continuous product improvement, specifications
are subject to change without notice.

Visit us on the web at www.york.com for the most
up-to-date technical information.

Additional rating information can be found at
www.gamanet.org.

WARRANTY

Lifetime limited warranty on both heat exchangers to the orig­inal purchaser; a 20-year limited warranty from original instal­lation date to subsequent purchaser.

10-year warranty on the heat exchanger in commercial appli­cations.

5-year limited parts warranty.

FEATURES

• Modulating heating operation includes:

- Modulating gas valve

- Modulating inducer operation

• Provides increased comfort level & very quiet unit opera­tion

• Compact, easy to install, ideal height 40" cabinet

• Blower-off delay for cooling SEER improvement.

• Easy to connect power/control wiring.

• Built-in, high level self diagnostics with fault code display.

• Low unit amp requirement for easy replacement applica­tion.

• Integrated control module for reliable, economical opera­tion.

• May be installed as either two-pipe (direct vent) or single
pipe vent (using indoor combustion air)

• Top intake & vent connection allows installation in narrow
locations.

• Electronic Hot Surface Ignition saves fuel cost with
increased dependability and reliability.

• Induced combustion system with inshot main burners for
quiet, efficient operation.

• No special vent termination kit required.

• 100% shut off main gas valve for extra safety.

• PSC -four speed, direct drive motor with large, quiet
blower.

• 24V, 40 VA control transformer and blower relay supplied
for add-on cooling.

• Hi-tech tubular aluminized steel primary heat exchanger.

• Secondary (condensing) heat exchanger of 29-4C high­grade stainless steel.

• Solid removable bottom panel allows easy application.

• Easy access from front of unit for cleaning, maintenance or
service.

• Protection from intake, exhaust or condensate blockage.

• Insulated blower compartment for quiet operation.

FOR DISTRIBUTION USE ONLY - NOT TO BE USED AT POINT OF RETAIL SALE

259720-CTG-B-0108

26-1/2
24-5/8

1-1/2” GAS
PIPE ENTRY

7/8” JUNCTION
BOX HOLE

T-STAT WIRING
7/8” K.O.

CONDENSATE
DRAIN 7/8” K.O.

OPTIONAL RETURN AIR
CUT-OUT (either side)
FOR USE WITH
EXTERNAL FILTER
FRAME

7/8

LEFT SIDE

23-3/4

30-1/8

11

7

21-1/2

13-7/8

7/8

26-3/4

BOTTOM IMAGE

RETURN END

30-7/8

FRONT

1-3/8

C

A

1-1/4

40

28-3/8

21-1/2

11

8

24-3/8

20

D

2

24-7/16

TOP IMAGE

SUPPLY END

5/8

5/8

B

26-1/2

25-3/8

1-1/2” GAS
PIPE ENTRY

7/8” JUNCTION
BOX HOLE

T-STAT WIRING
7/8” K.O.

CONDENSATE
DRAIN 7/8” K.O.

RIGHT SIDE

DIMENSIONS

Models

Nominal

CFM

Cabinet

Size

A (in.) B (in.) C (in.) D (in.)
FC9M060B12UP11 1200 B 17-1/2 16-1/4 14-1/2 8-1/2
FC9M080B12UP11 1200 B 17-1/2 16-1/4 11 8-1/2
FC9M080C16UP11 1600 C 21 19-3/4 18 8-7/8
FC9M100C16UP11 1600 C 21 19-3/4 18 8-7/8
FC9M100C20UP11 2000 C 21 19-3/4 18 8-7/8
FC9M120D20UP11 2000 D 24-1/2 23-1/4 21-1/2 10-5/8

Cabinet Dimension

2 Unitary Products Group

ELECTRICAL AND PERFORMANCE DATA

259720-CTG-B-0108

Models

Input

Max/Min

MBH MBH In. HP Amps °F °F

Output

Max/Min

Blower

Size

Blower

Max.

Over-current

Protect

Air Temp. Rise

Maximum Input

Air Temp. Rise

Minimum Input

FC9M060B12UP11 60/21 57/20 11 x 8 1/2 7.7 20 40 - 70 20 - 50
FC9M080B12UP11 80/28 76/26 11 x 8 1/2 7.7 20 40 - 70 20 - 50
FC9M080C16UP11 80/28 76/26 11 x 10 3/4 10.2 20 40 - 70 20 - 50
FC9M100C16UP11 100/35 95/33 11 x 10 3/4 10.2 20 40 - 70 20 - 50
FC9M100C20UP11 100/35 95/33 11 x 11 1 12.8 20 40 - 70 20 - 50
FC9M120D20UP11 120/42 115/39 11 x 11 1 12.8 20 40 - 70 20 - 50

Models

Max. Outlet

Air Temp.

°F CFM In. Amps %

Nominal

Airflow

Cabinet

Width

Total

Unit

AFUE

Min. Wire Size

(awg) @ 75 ft.

One Way

Approximate

Operating Weight

Power Supply

(Voltage-PH-Hz)

FC9M060B12UP11 170 1200 17-1/2 9 95.0 14 135 115-1-60
FC9M080B12UP11 170 1200 17-1/2 9 95.0 14 142 115-1-60
FC9M080C16UP11 170 1600 21 12 95.0 14 157 115-1-60
FC9M100C16UP11 170 1600 21 12 95.0 14 162 115-1-60
FC9M100C20UP11 170 2000 21 14 95.0 12 164 115-1-60
FC9M120D20UP11 170 2000 24-1/2 14 95.0 12 180 115-1-60

* ESP (External Static Pressure) .5" WG is at furnace outlet ahead of cooling coil.
Annual Fuel Utilization Efficiency (AFUE) numbers are determined in accordance with DOE Test procedures.
Wire size and over current protection must comply with the National Electrical Code (NFPA-70-latest edition) and all local codes.
The furnace shall be installed so that the electrical components are protected from water.

NOTES:

1. For altitudes above 2000 ft. reduce capacity 4% for each 1000 ft. above sea level.

2. Wire size based on copper conductors, 60°C, 3% voltage drop.

3. Continuous return air temperature must not be below 55°F.

4. All filters must be high velocity cleanable type.

5. Air flows above 1800 CFM require either return from two sides or one side plus bottom.

Unitary Products Group 3

259720-CTG-B-0108
For additional connection diagrams for all UPG e quipment refer to “Line Voltage System Wiring” document available on-line at

www.upgnet.com in the Product Catalog Section.

AC 11A Single Stage Air Conditioner – PSC Modulating Furnace

ID MODELS

PM9

FC9M

THERMOSTAT

FL9M

*PP11C70224

Y

Full Stage Compressor

RH
24 – Volt Hot
(Heat XFMR)

G

Fan

RC
24 – Volt Hot
(Cool XFMR)

W

Full Stage Heat

HM1

Humidistat

24VAC Humidifier

(Optional)

PSC

MODULATING

FURNACE

PSC

MODULATING FURNACE

C

24 – Volt Common

Y/Y2

Second or Full

Stage Compressor

R

24 – Volt Hot

G

Fan

W

Modulating Heat

Single Stage Compressor

Y1

SINGLE STAGE
SINGLE STAGE

AIR

AIR CONDITIONER

CONDITIONER

SINGLE STAGE

1

SINGLE STAGE

AIR CONDITIONER

AIR CONDITIONER

C

24 – Volt Common

Y

Y

Compressor

Compressor Contactor

Clipping Jumper W914 for
electric heat on thermostat

is not necessary

Thermostat Chart - PSC Modulating Furnace/Single Stage Air Conditioner

4 Unitary Products Group

Part Numbers:

SAP = Legacy

155941 = 031-09140

1

AC 11B Single Stage Air Conditioner – PSC Modulating Furnace

ID MODELS

PM9

FC9M

THERMOSTAT

THERMOSTAT

FL9M

259720-CTG-B-0108

*BN11C00124

C

24 – Volt Common

Y

Full Stage Compressor

RH
24 – Volt Hot
(Heat XFMR)

G

Fan

RC
24 – Volt Hot
(Cool XFMR)

W

Full Stage Heat

*BP11C50124
*BN11C01124
*DP11C40124

*DN11C00124

C

24 – Volt Common

Y

Full Stage Compressor

RH
24 – Volt Hot
(Heat XFMR)

G

Fan

RC
24 – Volt Hot
(Cool XFMR)

W

Full Stage Heat

PSC

MODULATING

FURNACE

PSC

MODULATING FURNACE

C

24 – Volt Common

Y/Y2

Second or Full

Stage Compressor

R

24 – Volt Hot

G

Fan

W

Modulating Heat

Single Stage Compressor

Y1

SINGLE STAGE

AIR

CONDITIONER

1

SINGLE STAGE

AIR CONDITIONER

C

24 – Volt Common

Y

Compressor Contactor

External Humidistat

Thermostat Installer Setup

1-System Type-must be

set to 0
Thermostat Installer Setup
15-Compressor Protection

must be set to 5

2

2

(Optional)

Open on Humidity Rise

Selection of GAS/ELEC

switch on thermostat

is not necessary

Part Number:

S1-2HU16700124

24VAC Humidifier

(Optional)

Part Numbers:

SAP = Legacy

155941 = 031-09140

1

Thermostat Chart - PSC Modulating Furnace/Single Stage Air Conditioner

Unitary Products Group 5

259720-CTG-B-0108

AC 11C Single Stage Air Conditioner – PSC Modulating Furnace

THERMOSTAT

THERMOSTAT

THERMOSTAT

THERMOSTAT

ID MODELS

PM9

FC9M

FL9M

*DN22U00124

C

24 – Volt Common

Y1

First Stage Compressor

R
24 – Volt Hot
(Heat XFMR)

G

Fan

E/W1

First Stage Heat

W2

Second Stage Heat

R
24 – Volt Hot
(Cool XFMR)

Y2
Second Stage

Compressor

*PP32U70124

C

24 – Volt Common

Y1

First Stage Compressor

R
24 – Volt Hot
(Heat XFMR)

G

Fan

E/W1

Emergency Heat

AUX

Auxiliary Heat

R

24 – Volt Hot

(Cool XFMR)

Y2
Second Stage

Compressor

*DN22C00124

C

24 – Volt Common

Y

First Stage Compressor

R

24 – Volt Hot

G

Fan

W

First Stage Heat

W2

Second Stage Heat

Y2

Second Stage

Compressor

*DP22U70124

C

24 – Volt Common

Y1

First Stage Compressor

R

24 – Volt Hot

G

Fan

E/W1

First Stage Heat

W2

Second Stage Heat

Y2

Second Stage

Compressor

External Humidistat

2

(Optional)

Open on Humidity Rise

24VAC Humidifier

(Optional)

PSC

MODULATING

FURNACE

PSC

MODULATING FURNACE

C

24 – Volt Common

Y/Y2

Second or Full

Stage Compressor

R

24 – Volt Hot

G

Fan

W

Modulating Heat

Y1

Single Stage Compressor

SINGLE STAGE
CONDITIONER

1

SINGLE STAGE

AIR CONDITIONER

24 – Volt Common

Compressor Contactor

AIR

C

Y

Connection of the “C”

terminal, 24-volt common

is optional when used with

batteries

Thermostat Installer Setup

1-System Type-must

be set to 7-2 Heat/1 Cool

Multistage Conventional

Thermostat Installer Setup
15-Compressor Protection

-must be set to 5

Connection of the “C”
terminal, 24-Volt common
is optional when used with

batteries

Thermostat Installer Setup

0170-System Type-must
be set to 9-2 Heat/1 Cool
Multistage Conventional

Connection of the “C”

terminal, 24-Volt common

is optional when used with

Thermostat Chart - PSC Modulating Furnace/Single Stage Air Conditioner

6 Unitary Products Group

batteries

Connection of the “C”

terminal, 24-Volt common

is optional when used with

batteries

Step 1 of Thermostat User

Configuration Menu must

be set to MS 2

2

Part Number:

S1-2HU16700124

Part Numbers:

SAP = Legacy

155941 = 031-09140

1

AC 11D Single Stage Air Conditioner – PSC Modulating Furnace

ID MODELS

PM9

FC9M

THERMOSTAT

FL9M

259720-CTG-B-0108

*PP32U71124
*PP32U72124

C

24 – Volt Common

Y1

First Stage Compressor

R

24 – Volt Hot

G

Fan

E/W1

First Stage Heat

W2

Second Stage Heat

O

Reversing Valve

Energized in Cool

L

Malfunction Light

Y2

Second Stage

Compressor

PSC

MODULATING

FURNACE

PSC

MODULATING FURNACE

C

24 – Volt Common

Y/Y2

Second or Full

Stage Compressor

R

24 – Volt Hot

G

Fan

W

Modulating Heat

Single Stage Compressor

Y1

SINGLE STAGE
SINGLE STAGE

AIR

AIR CONDITIONER

CONDITIONER

1

SINGLE STAGE

SINGLE STAGE

AIR CONDITIONER

AIR CONDITIONER

C

24 – Volt Common

Y

Y

Compressor

Compressor Contactor

DHM

Dehumidistat

HM

Humidistat

Step 1 of the Thermostat

Installer Table must be

set to MTLI STG

Step 5 of Thermostat User

Configuration Menu must

be set to “ON” for

Dehumidification

E2/P Switch must be in the

E2 position

24VAC Humidifier

(Optional)

Part Numbers:

SAP = Legacy

155941 = 031-09140

1

Thermostat Chart - PSC Modulating Furnace/Single Stage Air Conditioner

Unitary Products Group 7

259720-CTG-B-0108

HP 17A Single Stage Heat Pump – PSC Modulating Furnace (With Hot Heat Pump Operation)

THERMOSTAT

*DN22U00124

C

24 – Volt Common

Y1

First Stage Compressor

R

24 – Volt Hot

(Heat XFMR)

G

Fan

E

Emergency Heat

R
24 – Volt Hot
(Cool XFMR)

O/B

Reversing Valve

L

Malfunction Light

Second Stage Compressor

Thermostat Installer Setup
1-System Type-must be set
to 5 – 2 Heat/1 Heat Pump

Thermostat Installer Setup
2-Changeover Valve-must

be set to 0 – O/B terminal

Y2

AUX

Auxiliary Heat

Energized in Cooling

THERMOSTAT

*BP21H50124
*BN21H00124
*DP21H40124

*DN21H00124

C

24 – Volt Common

Y1

First Stage Compressor

R

24 – Volt Hot

G

Fan

E

Emergency Heat

O

Reversing Valve

Energized in Cool

L

Malfunction Light

Second Stage Compressor

B/O Switch on Thermostat

Y2

W2

Second Stage Heat

must be in the O position

THERMOSTAT

*DP32H70124

C

24 – Volt Common

Y1

First Stage Compressor

R

24 – Volt Hot

G

Fan

E

Emergency Heat

W2

Third Stage Heat

O

Reversing Valve

Energized in Cool

L

Malfunction Light

Second Stage Compressor

3

Y2

W1

Second Stage Aux. Heat

External Humidistat

(Optional)

Open on Humidity Rise

24VAC Humidifier

(Optional)

Step 1 of Thermostat

Installer / Configuration

Menu must be set to

Heat Pump 1

ID MODELS

PM9
FC9M
FL9M

PSC

MODULATING

FURNACE

PSC

MODULATING FURNACE

C

24 – Volt Common

Single Stage Compressor

Y1

R

24 – Volt Hot

G

Fan

W

Modulating Heat

Y/Y2

Second or Full

Stage Compressor

2

Bonnet Sensor

(Optional)

OD MODELS

YZB
YMB

H*3

SINGLE STAGE

HEAT PUMP

YORKGUARD VI

CONTROL

C

24 – Volt Common

Y1

Single Stage Compressor

R

24 – Volt Hot

W1 OUT

First Stage Heat

W2 OUT

Second Stage Heat

Y2 OUT

Second Stage Compressor

O

Reversing Valve

Energized in Cool

X/L

Malfunction Light

Second Stage Compressor

on the heat pump control

jumper on the heat pump

Y2

W

Auxiliary Heat

BSG

Bonnet Sensor

BS

Bonnet Sensor

Change FFuel jumper

to “ON”

Change Hot Heat Pump

control to “ON”

1

3

Thermostat Chart - PSC Modulating Furnace/Single Stage Heat Pump

8 Unitary Products Group

Part Number:

S1-2HU16700124

Part Numbers:

SAP = Legacy

155941 = 031-09140

2

Part Numbers:

SAP = Legacy

126768 = 031-09137
18395 = 031-01996
340512 = 031-09178

1

BLOWER PERFORMANCE CFM - COOLING

COOLING AIRFLOW WITH BOTTOM OR ONE SIDE RETURN

MODELS

FC9M060B12UP11
FC9M080B12UP11

FC9M100C20UP11

FC9M080C16UP11
FC9M100C16UP11

FC9M120D20UP11

MODELS

Input/

Airflow/Cabinet

FC9M100C20UP11

FC9M120D20UP11

NOTE: Low cool (W1) airflow is 65% of high cool airflow.

Speed

Tap

A 1650 1605 1570 1525 1465 1410 1350 1275 1170 1060
B 1165 1185 1175 1165 1150 1140 1100 1050 970 875
C 895 915 935 940 940 920 905 860 815 750
D 710 725 725 725 720 700 685 660 625 560
A 2300 2210 2120 2020 1930 1830 1715 1595 1480 1350
B 1950 1900 1830 1755 1680 1595 1500 1390 1270 1155
C 1610 1545 1490 1440 1390 1315 1230 1155 1050 920
D 1325 1270 1225 1175 1105 1045 990 905 890 790
A 1960 1955 1925 1890 1830 1765 1695 1615 1600 1485
B 1565 1560 1560 1575 1545 1530 1475 1425 1365 1260
C 1230 1275 1285 1300 1310 1300 1280 1245 1190 1070
D 930 945 965 975 975 975 975 950 910 850
A 2560 2485 2410 2320 2220 2135 2035 1920 1785 1650
B 2090 2050 1990 1970 1885 1820 1760 1675 1545 1405
C 1695 1675 1665 1615 1565 1510 1460 1385 1285 1140
D 1175 1150 1135 1110 1085 1055 1005 980 970 845

0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0

CFM CFM CFM CFM CFM CFM CFM CFM CFM CFM

COOLING AIRFLOW WITH TWO SIDE RETURNS OR WITH BOTTOM AND ONE SIDE RETURN

Speed

Tap

A 2465 2380 2295 2195 2095 1995 1875 1760 1620 1470
B 2085 2035 1960 1880 1800 1705 1605 1485 1360 1235
C 1725 1625 1595 1540 1485 1405 1315 1235 1125 995
D 1420 1360 1310 1255 1180 1120 1070 970 950 845
A 2615 2535 2450 2385 2285 2175 2075 1945 1825 1670
B 2055 2045 2015 1985 1932 1855 1785 1730 1605 1470
C 1690 1650 1620 1600 1570 1525 1470 1395 1300 1200
D 1345 1335 1335 1285 1250 1230 1180 1115 1010 850

0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0

CFM CFM CFM CFM CFM CFM CFM CFM CFM CFM

259720-CTG-B-0108

EXTERNAL STATIC PRESSURE, INCHES W.C. (kPa)

EXTERNAL STATIC PRESSURE, INCHES W.C. (kPa)

Blower speed adjustments should be done by moving the COOL jumper on the control
board. DO NOT move the motor wires to different positions on the furnace control board.

NOTES:

1. Airflow expressed in standard cubic feet per minute (CFM).

2. Return air is through side opposite motor (left side).

3. In order to stay within the velocity rating the filters, airflows above 1800 CFM require eit her return from two sides or one side plus bottom.

4. Motor voltage at 115 V.

FILTER PERFORMANCE

FILTER PERFORMANCE - PRESSURE DROP INCHES W.C.

The airflow capacity data published in the “Blower Perfor­mance” table listed above represents blower performance
WITHOUT filters. To determine the approximate blower per­formance of the system, apply the filter drop value for the fil­ter being used or select an appropriate value from the “Filter
Performance” table shown.

NOTE: The filter pressure drop values in the “Filter Perfor­mance” table shown are typical values for the type of filter
listed and should only be used as a guideline. Actual pres­sure drop ratings for each filter type vary between filter manu­facturer.

Airflow Range

CFM

0 - 750 230 0.01 0.01 0.15

751 - 1000 330 0.05 0.05 0.20
1001 - 1250 330 0.10 0.10 0.20
1251 - 1500 330 0.10 0.10 0.25
1501 - 1750 380 0.15 0.14 0.30
1751 - 2000 380 0.19 0.18 0.30

2001 & Above 463 0.19 0.18 0.30

Minimum

Opening Size

2

in

Disposable

In W.C. In W.C. In W.C.

Filter Type

Washable

Fibers

Pleated

Unitary Products Group 9

259720-CTG-B-0108

APPLYING FILTER PRESSURE DROP TO
DETERMINE SYSTEM AIRFLOW

To determine the approximate airflow of the unit with a filter in
place, follow the steps below:

1. Select the filter type.

2. Select the number of return air openings or calculate the
return opening size in square inches to determine the
proper filter pressure drop.

3. Determine the External System Static Pressure (ESP)
without the filter.

4. Select a filter pressure drop from the table based upon
the number of return air openings or return air opening
size and add to the ESP from Step 3 to determine the
total system static.

5. If total system static matches a ESP value in the airflow
table (i.e. 0.20, 0.60, etc,) the system airflow corre­sponds to the intersection of the ESP column and Model/
Blower Speed row .

6. If the total system static falls between ESP values in the
table (i.e. 0.58, 0.75, etc.), the static pressure may be
rounded to the nearest value in the table determining the
airflow using Step 5 or calculate the airflow by using the
following example.

Example: For a 120,000 Btuh furnace with 2 return openings
and operating on high speed blower, it is found that total sys­tem static is 0.58" w.c. To determine the system airflow, com­plete the following steps:

1. Obtain the airflow values at 0.50" & 0.60" ESP.
Airflow @ 0.50": 2285 CFM
Airflow @ 0.60": 2175 CFM

2. Subtract the airflow @ 0.50" from the airflow @ 0.60" to
obtain airflow difference.

2175 - 2285 = -110 CFM

3. Subtract the total system static from 0.50" and divide this
difference by the difference in ESP values in the table,

0.60" - 0.50", to obtain a percentage.
(0.58 - 0.50) / (0.60 - 0.50) = 0.8

4. Multiply percentage by airflow difference to obtain airflow
reduction.

(0.8) x (-110) = -88

5. Subract airflow reduction value to airflow @ 0.50" to
obtain actual airflow @ 0.58" ESP.

2288 - 88 = 2197

UNIT CLEARANCES TO COMBUSTIBLES

APPLICATION

UPFLOW 1 3 0 0 0 0 COMBUSTIBLE YES YES

ACCESSORIES

PROPANE (LP) CONVERSION KIT ­1NP0680 - All units

This accessory conversion kit must be used to convert natu­ral gas (N) units for propane (LP) operation. Conversions
must be made by qualified distributor or dealer personnel.

CONCENTRIC VENT TERMINATION -
1CT0302 (2")
1CT0303 (3")
For use through rooftop, sidewall. Allows combustion air to

enter and exhaust to exit through single common hole.

CONDENSATE NEUTRALIZER KIT - 1NK0301

Neutralizer cartidge has a 1/2" plastic tube fittings for installa­tion in the drain line. Calcium carbonate refill media is also
avaiable from the Source 1 Parts (p/n 026-30228-000).

SIDEWALL VENT TERMINATION -
1HT0901 (3")

TOP FRONT REAR LEFT SIDE RIGHT SIDE FLUE

In. In. In. In. In. In.

SIDE RETURN FILTER -

1SR0402 - All Models
1SR0200 - All Models

BOTTOM RETURN FILTER -

1BR0117 or 1BR0217 - For 17-1/2” cabinets
1BR0121 or 1BR0221 - For 21” cabinets
1BR0124 or 1BR0224 - For 24-1/2” cabinets

ROOM THERMOSTATS - A wide selection of compatible
thermosets are available to provide optimum performance
and features for any installation.

1H/1C, manual change-over electronic non-programmable
thermostat.

1H/1C, auto/manual changeover, electronic programmable,
deluxe 7-day, thermostat.

1H/1C, auto/manual changeover, electronic programmable.
* For the most current accessory information, refer to the

price book or consult factory.

FLOOR/

BOTTOM

CLOSET
ALCOVE

1HT0902 (2")
For use on sidewall, two-pipe installations only. Provide a

more attractive termination for locations where the terminal is
visable on the side of the home.

ATTIC

10 Unitary Products Group

NOTES

259720-CTG-B-0108

Unitary Products Group 11

NOTES

Subject to change without notice. Printed in U.S.A. 259720-CTG-B-0108
Copyright © by Unitary Products Group. 2008. All rights reserved. Supersedes: 259720-CTG-A-0606

Unitary 5005 Norman
Products York OK
Group Drive 73069