Coleman 9830-330, Exponent Heka X2 9830-330 Instructions Manual
Main Tent Pole (red)
Part No. 9830-1441
Front Crossover Pole (silver)
Part No. 9830-1141
Back Crossover Pole (gold)
Part No. 9830-1241
POLE ASSEMBLY PARTS
Heka X2
part number 9830-330
Rainfly
Removable Vestibule
Part No. 9830-1341
Part No. 9850-3071
1
2
Layout & Positioning
of Tent, Pole Assembly
– Layout and position tent with door facing
desired direction. (illus. 2)
– For best results in windy conditions, postion
door or back of tent into the wind.
– Stake down tent corners. Keep the floor
taut. Unzip door. (illus. 1, illus. 2)
– Assemble Frame Poles by interlocking the
shock-corded sections. This will make one long
Main Pole and two shorter Crossover Poles.
– Insert the Main Pole (Red) through the pole
sleeves and through the grommet going from
the back of the tent to the front of the vestibule
webbing strap. (illus. 2, illus. 3)
– Insert the silver Crossover Pole in the front set
of pole sleeves going side to side. (illus. 2)
– Insert the gold Crossover Pole in the back set
of pole sleeves going side to side. (illus. 2)
Connect Frame to Tent
– Insert Pole Tip of Main Tent pole into the grommet
on the webbing at the back of the tent (illus. 5).
– Go to opposite end of the Main Pole and
gradually apply pressure to the pole, forming an
arch, until you are able to insert the pole tip
into the pole pocket at the point of the pole flap.
(illus. 4, illus. 5)
– Insert the Crossover Pole into the grommet
on the webbing located on the side of the
tent. The front pole goes toward the back.
The back pole angles toward the front. The
Crossover Poles will cross on each side.
(illus. 4, illus. 5)
Crossover Poles through pole sleeves
illus. 2
illus. 3
Long pole through
grommet
Front Crossover Pole
Main Pole
illus. 4
Insert Pole Tip into
illus. 1
Tent stake
through
Loop
Front Pole (silver)
Back Pole (gold)
Main Pole (red)
Back
Crossover Pole
illus.5
grommet
3
Attach Tent to Frame
Using Frame Clips
4
– Attach remaining frame clips
along the side of tent and webbing
to frame poles (illus. 6), (illus. 7)
– Make any adjustments to the tent
corner stakes that are needed.
illus. 7
Assembled tent without
Rainfly. Note the frame
clips located on edge of tent.
Attach Rainfly with
Convertible Vestibule
– Drape Rainfly main section or zipped 2
sections over tent frame. Curved door
goes in front.
– Secure Rainfly with Frame Ties located
on underside of fly.
– Connect the clips (found at the
Rainfly points) to the clips located at
the points of the tent. (illus. 9)
– Insert the Main Pole end over the door into
the pole pocket on the underside of the
main section of the Rainfly.(illus. 11)
– Convertible vestibule section can be
zipped on or removed as desired.
When attaching also toggle it to the
main section for added stability.
– Attach Guy Lines and stake out.
(illus.11)
illus. 10
Completed tent and Rainfly with
Convertible Vestibule.
illus. 6
Frame Clips
illus. 8
Rainfly with
Convertible
Vestiblue shown
zipped together
Guy Line
Zips together
Convertible
Vestibule
Main Section
Guy Line
illus. 9
Rainfly clips
onto pole
stake loop
Things You Should Know
Under certain conditions (cold weather, high humidity, etc.) condensation will form on the inside surfaces of your tent. Condensation
•
is caused by water vapor from your breath, perspiration, or any wet clothing inside your tent. It is NOT LEAKAGE through the tent
fabric. It can be minimized by removing wet clothing from your tent and by providing good ventilation through the tent.
Never stor
•
drying it thoroughly and brushing off caked dirt. Do not pack
stakes or poles inside your tent. Use separate storage bag.
STAKES SHOULD BE REMOVED BY PULLING ON THE STAKE
•
ITSELF. NEVER PULL ON THE TENT FABRIC OR TENT STAKE
LOOP TO REMOVE STAKE.
PRINTED IN CHINA
The Coleman Company, Inc. All Rights Reserved.
2006
©
e tent, even for a shor
t period of time, without
illus. 11
Completed tent with
Convertible Vestiblue removed.
3600 N. Hydraulic • Wichita, Kansas 67219
1-800-835-3278 • www.coleman.com
Loading...