Coleman EVEN HEAT 85-1978 Care And Safety Instructions

DURABILITY • POWER • PERFORMANCE

EVEN HEAT™

BURNER

Includes: 1X Burner, 1X Screw, 1X M4 Wing Nut, 1X Lock Washer

CARE AND SAFETY INSTRUCTIONS

PART NUMBER: 85-1978 (G522-B600-02)

EXACT FIT FOR COLEMAN® EVEN HEAT™ MODELS:

2010
2011/ 2012

2013

2014

2015

2016

READ AND SAVE MANUAL FOR FUTURE REFERENCE.

The Coleman® Even Heat™ Burner is designed and intended for use with

Coleman® Even Heat™ Barbecues ONLY. This product will replace the original

Even Heat™ burner sold with your Coleman® Even Heat™ Barbecue.

85-3026-0 (G52201), 85-3027-8 (G52202), 85-3028-6 (G52203), 85-3029-4 (G52204)

85-3046-2 (G35301), 85-3047-0 (G35302), 85-3026-0 (G52205), 85-3027-8 (G52206),
85-3028-6 (G52207), 85-3029-4 (G52208), 85-3046-2 (G35303), 85-3047-0 (G35304),
85-3026-0 (G52209), 85-3027-8 (G52210), 85-3028-6 (G52211), 85-3029-4 (G52212)

85-3066-4 (G35305), 85-3067-2 (G35306), 85-3068-0 (G52215), 85-3069-8 (G52216),
85-3074-4 (G52217), 85-3075-2 (G52218), 85-3076-0 (G53101), 85-3077-8 (G53102)

85-3066-4 (G35305), 85-3067-2 (G35306), 85-3068-0 (G52220), 85-3069-8 (G52221),
85-3092 (G52222), 85-3093-8 (G52223), 85-3076-0 (G53103), 85-3077-8 (G53104)

85-3066-4 (G35308), 85-3067-2 (G35309), 85-3068-0 (G52227), 85-3069-8 (G52228),
85-3092-0 (G52229), 85-3093 (G52230), 85-3076 (G53103), 85-3077 (G53104)

85-3066 (G35308), 85-3067 (G35309), 85-3076 (G53103), 85-3077 (G53104)

www.colemanbbqs.com

Manual Revision #: 01022018 PD

REPLACING YOUR EVEN HEAT™ BURNERS

ATTENTION

Move grill to an open outdoor area prior to removing old Even Heat™ Burners and installing
your NEW replacement Even Heat™ Burners. Ensure grill is cool before proceeding, and close
the control knob(s) and gas supply.

ATTENTION

85-3026-0 (G52201), 85-3027-8 (G52202), 85-3028-6 (G52203), 85-3029-4 (G52204)

1

If you have a 2010 Coleman® Even Heat™ Barbecue

use the following instructions:

Open the top lid. Remove the
warming rack, cooking grates and heat
distribution plates from the burner box
figure 1.

2

3

Remove the two tapping screws from the
3 or 4 electrodes, as shown in figure 2.

Locate and remove the Wing Nut used to
attach the burner to the carryover bar, as
shown in figure 3.

2