The Coleman Company, Inc. • 3600 N. Hydraulic • Wichita, Kansas 67219
1-800-835-3278 • www.coleman.com
MADE IN CHINA • PRINTED IN CHINA
© 2007 The Coleman Company, Inc.
Coleman
®
and are registered trademarks of The Coleman Company, Inc.
Things You Should Know:
• Under certain conditions (cold weather, high humidity, etc.) condensa-
tion will form on the inside of your tent. Condensation is caused by
water vapor from your breath, perspiration, or any wet clothing inside
the tent. It is NOT LEAKAGE through the tent fabric. It can be minimized
by removing wet clothing from your tent and by providing good ventilation through the tent.
• Never store tent, even for a short period of time, without drying it
thoroughly and brushing off caked dirt. Do not pack stakes or poles
inside your tent. Use a separate storage bag.
• STAKES SHOULD BE REMOVED BY PULLING ON THE STAKE ITSELF.
NEVER PULL ON THE TENT TO REMOVE STAKE.
• TENT POLES SHOULD NOT BE LEFT TELESCOPED TOGETHER
DURING STORAGE.
• Do not leave your tent set-up for weeks at a time. Be aware that exposure
to ultraviolet rays from the sun can seriously damage material and/or
cause it to become discolored.
WARNING: Keep all flame and heat sources away
from this tent fabric.
This tent meets the flammability requirements of CPAI-84. The
fabric may burn if left in continuous contact with any flame source.
The application of any foreign substance to the tent fabric may
render the flame-resistant properties ineffective.
STITCH LINE
7. Extend front
flaps on rainfly
and secure with
stakes. (Fig. 13)
Note: Flaps may be
rolled back and
secured by inserting
toggles through
fabric loops. (Fig. 14)
Fig. 13
Guyline
To Attach Rainfly continued
Fig. 14
8. Attach guylines to web straps on rain
fly and stake out.
Cooler Access
The smaller zippered opening at the
rear of the tent is designed for added
ventilation and easy access to your
beverage cooler.
1. To use as a vent, unzip flap to
expose screen. (Fig.21)
2. To use as a cooler access, unzip
other flap to make an avenue to
bring beverages into the tent.
(Fig.22)
Fig. 21
Fig. 22
To Store
1. All metal poles and stakes must to be placed in the storage
bag to prevent damage to the fabric items placed in the
carry case.
2. Make sure tent is clean and dry before placing in carry case.
3. Remove rainfly, spread out on floor of tent, then unzip
door & vents before taking tent down for storage.
4. Neatly fold tent to width of pole storage bag, place on tent,
roll tightly, and place in carry case.
5. Store in a clean, dry area.
Electrical Cord Access
1. Unzip access panel in
the lower right corner
of tent and bring in
electrical cord.
Use only UL approved
cords that are rated
for outdoor usage.
(Fig. 23)
Fig. 23
4. For better ventilation, unnzip flap on
door, roll down, and insert toggle into
fabric loop to secure. (Fig. 18)
5. To open back and side window vents
for more ventilation, unzip, then roll up
and insert toggles through fabric loops.
(Fig. 19 & 20)
Fig. 20
Fig. 19
Door and Window Vents
1. Assemble Vertical Hinge Door pole (shorter black pole with
plastic cap tips); insert into zippered vertical pocket on
hinged side of door. (Fig. 15)
2. Assemble Hinge Door pole (longer black pole with plastic
cap tips) insert into zippered pocket at bottom of door.
(Fig. 16)
3. Insert ends of both door poles into sockets at top and
bottom of door on hinged side. (Fig. 17)
Fig. 16
Fig. 17
Fig. 15
Fig. 18
Rev12/07