Coleman DUAL OVERFL User Manual

Connect Frame to Tent

– Insert one end of main tent pole onto pin of

pin & ring system at tent corner. (illus. 3), (illus. 4)

– Go to opposite end of pole and gradually apply

pressure to the pole forming an arch until you

are able to insert the pin into the pole. – Repeat for second pole. (illus. 3), (illus. 4) – Repeat for second tent. (illus. 4)

DUAL OVERFLY XL

™

10’x7’

Layout & Positioning of Tent, Pole Assembly

– Layout and position tents where desired

with doors facing each other. Allow

aproximately 6’ between them.(illus. 1) – Unzip doors. – Partially stake down the tents using the rings of

the pin & ring system at the corners of the tent.

Keep the floor taut. (illus. 2) Do not fully stake

down, you may need to make adjustment s later.

– Assemble main tent poles (black) by

interlocking shock-corded poles. This will

make two long poles for each tent. – Insert the poles diagonally into pole sleeves.

The center of the poles should cross forming an “X” in the middle of tent. (illus. 1)

When You Are Ready To Set Up Your Tent

–Select a level campsite clear of

rocks, branches and other hard or

sharp objects. –Do not set up your tent under trees. –For best results in windy conditions,

position the end of tent into the wind.

Center Ridge Pole Connecting Room (Gray)

Assembled black main tent poles inserted through pole sleeves

Instructions apply to Part Number 9232-107

illus. 2

Tent stake

through ring

on stake loop

illus. 3

Assembled

tents without

rainflys

Part No. 9230-320

Part No. 9232-322

Part No. 9232-324

Part No. 9232-326

Main Tent Poles for 10x7 Dome Tents (Black)

Rainfly Poles for 10x7 Dome Tents (Black)

Side Pole Connecting Room (Black)

Rainfly 10x7 Dome Tents Part No. 9238-328

Doors

Attach Tent to Frame Using Frame Clips

– Attach frame clips along the edges of tent to

frame poles. (illus. 3), (illus. 5)

– Make any adjustments to the tent corner

stakes that are needed.

illus. 5

Frame clips

illus. 4

Insert pin into

pole end

illus. 1

Tents positioned

with poles through

poles sleeves

illus. 6 Insert rainfly pole piece into pockets on underside of rainfly

illus. 8

Hooks attaches to

fabric loop

THE COLEMAN CO., INC.

3600 N. Hydraulic • Wichita, Kansas 67219

1-800-835-3278 • www.coleman.com

MADE IN THAILAND

PRINTED IN THAILAND Rev. 10/04

Things You Should Know

•

Under certain conditions (cold weather, high humidity, etc.) condensation will form on the inside surfaces of your tent. Condensation is caused by water vapor from your breath, perspiration, or any wet clothing inside your tent. It is NOT LEAKAGE through the tent fabric. It can be minimized by removing wet clothing from your tent and by providing good ventilation through the tent.

•

Never store tent, even for a short period of time, without drying it thoroughly and brushing off caked dirt. Do not pack stakes or poles inside your tent. Use a separate storage bag.

•

STAKES SHOULD BE REMOVED BY PULLING ON THE STAKE ITSELF. NEVER PULL ON THE TENT FABRIC OR TENT STAKE LOOP TO REMOVE STAKE.

•

TENT POLES SHOULD NOT BE LEFT TELESCOPED

TOGETHER DURING STORAGE.

•

Seam sealer has not been provided with your tent. For additional protection we recommend seam sealing your tent prior to camping. Seam sealer may be purchased through your local retailer or at your local sporting goods store.

•

Do not leave your tent set-up for weeks at a time, be aware that exposure to the ultraviolet rays of the sun can seriously damage material and/or cause it to become discolored.

WARNING: KEEP ALL FLAME AND HEAT SOURCES AWAY FROM THIS TENT FABRIC. This tent meets the flammability requirements of CPAI-84. The fabric will burn if left in continuous contact with any flame source. The application of any foreign substance to the tent fabric may render the flame-resistant properties ineffective.

Underside of rainfly attaches to tent frame

Attach Tent Rainflys

– Assemble tent rainfly poles by

interlocking shock-corded pole.

– Insert rainfly pole into the pole pocket

located at the center edges of the underside of rainfly. (illus. 6), (illus. 7)

– Drape rainfly over tent frame, pole side

down. Rainfly pole should be over door and rear window. NOTE: The toggles on the rainfly need to run from the front corners to the top of the tent.

– Connect the four elastic loops with hooks,

(found at the rainfly corners) to the fabric loops on the bottom row of frame clips.

– Secure rainfly with attachments

located on underside of fly. (illus. 7)

– Repeat for second tent.

Connecting Room

– Layout connecting room and assemble center

ridge and side poles.

– Insert the center ridge pole (gray) through ridge

pole sleeves and insert the pole ends into the pole pockets. (illus. 9)

– Insert the side poles through the pole sleeves

on connecting room. (illus. 9) Position connecting room between tents, pole side up.

– Insert one end of side pole onto pin of pin & ring

system on the stability strap. (illus. 3)

– Go to opposite end of pole and gradually apply

pressure to the pole forming an arch until

you are able to insert the pin into the pole. – Repeat for second pole. (illus. 9), (illus. 10) – Move tent as needed for better fit with

connecting room. Fully stake down tents. – Attach connecting room to the tents with

toggles & loops on rainfly and hooking the

stake loop ring at the tent corners. (illus. 10) – Stake out the tents with (2) side guylines

each and the connecting room with

(4) guylines. (illus. 8)

illus. 7 Both tents fully assembled with rainflys

illus. 9 Connecting room with center ridge pole and side poles in position

illus. 10 Both tents and connecting room completed

Guylines

Stability

strap

Toggles & Loops

secure connecting

room to tents

Center ridge pole sleeves

Pole pocket