Coleman 9992-449 User Manual
Liquid Propane Conversion Kit
IMPORTANT
Read this document carefully before attempting installation
of this conversion kit. These instructions should be left with
the consumer for future reference.
For the following Coleman® Gas Barbecue Grills:
8350 Series (M/N 9992-648)
WARNING
• This Liquid Propane conversion Kit must be installed only by a qualified service technician.
• Gas supply system must be installed in accordance with the U.S.
National Fuel Gas Code.
• This appliance and its individual shut off valve must be disconnected
from the gas supply piping system during any system pressure test in
excess of 1/2 PSI (3.5 KPA).
• Use a system manual shut off valve to shut off the gas supply to this
gas appliance before continuing with installation procedures.
WARNING
• If the information in this document is not followed exactly, a fire or
explosion may result causing property damage, personal injury or loss
of life. Read the Coleman®
Gas Barbecue Use, Care & Assembly
Manual With Grill Lighting Instructions,
before attempting installation
of this conversion kit.
WARNING
• TURN OFF THE GAS SUPPLY!
DO NOT attempt to install this Natural Gas Conversion Kit
while the barbecue is in operation or is hot.
Installation and provision for combustion and ventilation air
must conform with the
National Fuel Gas Code, ANSI Z223.1
,
or
CAN/CGA-B149.1, Natural Gas Installation Code
, or
CAN/CGA-B149.2, Propane Installation Code
.
WARNING
A liquid propane tank, not connected for use with this gas barbecue,
shall not be stored in the vicinity of this or any other appliance.
Note: These instructions apply to
grill Model 8350 Series
. The parts
included are designed for your
specific grill. The illustrations may
differ slightly from model to
model.
Turn off and disconnect from Natural Gas
service line prior to servicing grill.
Item No. Qty Description
1 9992-4421 1 Main Burner Valve & Manifold Assembly (L.P.) 8350
2 47310103 1 Main Regulator Hose Assembly (L.P.)
3 08006001 1 Rear IR L.P. Orifice (8350)
4 08138381 1 Connector 3/8" FNPT x 3/8" MFLR
5 49900004 1 Pipe Sealant
6 9992-462 1 LP Conversion Sticker
Liquid Propane Gas Conversion Instructions
2
4
5
2
6
1
3
Tools Needed:
Phillips head screwdriver
1/4" nut driver *
9/16" wrench
Adjustable wrench
Fig 4
Fig 1
Fig 2
Fig 3
Rear Heat Shield
Screws
Heat Tents
Screws
* socket set with extension can also be used.
Be sure gas supply is off, the knobs are in the off
position and the grill is cool.
1. Remove cooking grates and heat tents.
(See Fig. 1).
2. Remove the screws holding the rear heat shield
in place. Lift out rear heat shield and set
aside (Fig. 2).
3. Remove the two screws holding each igniter in
place (Fig. 3).
4. Lay igniters on floor of grill (Fig. 4).
Liquid Propane Gas Conversion Instructions
3
Fig 5
Fig 6
Side Screws
(Repeat on left side)
Screws
under lip
Fig 8
Fig 7
Tabs
5. Remove the screws from the bottom of the heat
shield, holding the front heat shield in place. The
screws are located under the bottom lip of the
shield (Fig. 5).
6. Remove the side heat shield screws located under
the bottom lip of the heat shield. Remove all of
the top heat shield screws (Fig. 6).
7. Remove the front heat shield (Fig. 7).
8. Grasp and push the burners towards the rear of
the grill to detach the burner from the
valves (Fig. 8).
9. Angle the burners up and remove (Fig. 8).
Liquid Propane Gas Conversion Instructions
4
Loading...