Coleman 5055-710 User Manual

Assembly and Instruction Sheet

Dome Fireplace

Model 5055-710

Follow these instructions for assembly and read carefully, particularly the safety statements. The safety alert symbol, is a universally recognized symbol used to identify safety information about hazards that can result in personal injury. When this symbol is used you should pay very close attention to what is written. Review these instructions before beginning assembly or using your fireplace.

• Check package for all parts needed for assembly.

• Check all items for shipping damage. Call Coleman at 1-800-835-3278 or TDD: 316-832-8707 if you have any problems.

FOLLOW INSTRUCTIONS AND WARNINGS TO AVOID FIRE,

SERIOUS INJURY OR DEATH.

• Outdoor use only. Never use in enclosed area. Use in unventilated areas will endanger your life.

• Keep away from all combustible materials including gasoline and other flammable liquids and vapors.

• Use on a level, noncombustible surface only. Keep away from house, garage, balconies, or eave overhangs.

• Keep out of the reach of children.

• Be sure screen is in place while in use and do not use in windy conditions.

• Do not overfill firebowl or use to burn leaves and trash.

• Exercise the same care you would with an open fire.

• Never leave unit unattended when hot or in use.

• Completely extinguish fire before leaving.

• Use gloves when handling or moving. Ashes can remain warm for a long time after extinguishing.

• Dispose of cold ashes properly.

• Do not modify in any way nor use with parts not expressly approved by Coleman.

• Combustion by-products produced when using this product contain chemicals known to the State of California to cause cancer, birth defects,

or other reproductive harm.

Contact local authorities regarding possible burn restrictions before using product.

WARNING

Assembly

Fireplace Parts Check List

Assembly (cont.)

3a. Assemble Leg Support Ring to the four leg assemblies.

Fasten to Leg Brackets with one small screw per leg (see arrows). Tighten all fasteners.

■■ 1. Firebowl

■■ 2. 4 Pc. Screen Assembly

■■ 3. Handle

■■ 4. Dome Lid

■■ 5. Protective Cover

■■ 6. Top Ring

■■ 7. Leg Support Ring

■■ 8. Screen Support Rings (2)

■■ 9. Hardware Kit

■■ 10. Leg Assemblies

■■ 11. Grates

Top

Ring

(Large)

1. Carefully unpack all parts from shipping box. NOTE: In

Steps 2 and 3, the stand is assembled up side down

for ease of assembly. Use a ground cloth to protect the finish.

2. Align holes in Leg Assembly Brackets with holes in Top

Ring. Attach with two small screws per leg. Hand tighten.

3b. Install four foot pads, one into each leg.

NOTE: In some models, the foot pads are

pre-installed by the factory.

4a. To assemble screen, align holes in the 3 screen panels with the holes

on outside edge of screen support ring. Attach with small screws and hex nuts but do not tighten at this time. NOTE: Make sure latch bracket panel and hinge panel are positioned as shown for proper installation.

Latch Bracket pointing up

Hinge Panel

6a. Assemble screen door latch.

NOTE: Two hex nuts and latch bar

will assemble on the inside of the screen door.

{

(See Note)

6b. Insert handle from outside.

Loosely assembly one hex nut. The handle should freely turn. Point the handle downward to begin the next step.

6c. Slip latch bar onto handle

threads. Align “D” slot in latch bar with flat on handle threads. The latch bar should point toward the left. Assemble the second hex nut to finish the assembly. This hex nut functions as a “jam nut”, and will tighten against the first hex nut assembled in Step 5b.

6d. Tighten the “jam nut” with

a wrench.

6e. Proper installation of the

latch assembly.

7. Install the firebowl.

8. Install two grates.

NOTE: An inch or two of sand should

be used in firebowl beneath the grate.

Assembly (cont.)

Handle

Latch

Bar

5. Turn frame right side up. Place Screen Assembly into frame. Make sure

door is centered between two Leg Assemblies, and can open and close properly.

4b. Align holes in the 3 screen

panels with the holes on outside edge of the remaining screen support ring. Attach with small screws and hex nuts. Tighten all screws and hex nuts on the screen assembly at this time.

4c. Install screen door by inserting pins into hinge slots on the screen

hinge panel

+ 2 hidden pages