Coleman 2000001598 User Manual

WEATHERMASTER

10 TENT MODEL 2000001598

Before you begin

Read all instructions before set up.

• Select a level site clear of rocks, branches, and other hard or sharp objects, to install your tent.

WARNING: Keep clear of overhead power lines

• Do not set up your tent under trees because of potential lightning strikes or falling tree limbs in inclement weather.

• Secure with all or personal injury.

• For best results in windy conditions, position narrow end of tent into the wind.

• Enlist the help of at least one other person to assist you when it is time to assemble the tent.

stakes and guylines provided to prevent property damage

Pole Descriptions

Description Qty. Dia. Repair Kit Replacement Kit

Long Leg Pole, steel

(w/ red marking) 2 19mm N/A 5010000614

Short Leg Pole, steel 4 19mm N/A 5010000623

Curved Ridge Pole, steel

(w/ red marking) 1 19mm N/A 5010000613

Curved Ridge Pole, steel 2 19mm N/A 5010000615

Side Window Pole, black,

fiberglass, metal tips 2 8.5mm 5010000541 5010000547

Door Pole, long, thin ,black,

fiberglass, rubber tips 1 6.3mm 5010000543 5010000545

Vert. Door Pole, short, black,

fiberglass, rubber tips 1 6.3mm 5010000543 5010000545

Pole Pole Pole

To Set Up Tent

1. Unfold tent and spread out on a clean, level surface with the

door facing the desired direction. Unzip doors. (Fig. 1)

Fig. 5

Door

Ridge Pole with

Red Marking

Curved End of Long Leg Pole

Ridge Pole

with Red

Marking

Button in third hole

STITCH LINE

2. Pull four corners of tent taut, then secure by

driving stakes through web loops at an angle for better anchoring. (Fig. 2)

3. Assemble three, steel, shock-corded,

curved Ridge Poles. Insert Ridge Pole (with red marking) into center sleeve on top of tent with the red trim (Fig. 3). Insert the remaining curved Ridge Poles into the other two sleeves on top of tent.

4. Assemble six, steel, shock-corded, Leg Poles. Push down

on steel button on tapered end and insert into end with four holes. NOTE: Make sure steel button locks into third hole on pole as shown. (Fig.4)

5. Insert curved end of Leg Poles

(with red marking) into the ends of the Ridge Pole (with red marking). Insert curved end of remaining short Leg Poles into the ends of the remaining Ridge Poles. (Fig. 5 & 6)

Ridge Pole with Red Marking in

center sleeve

Fig. 2

Fig. 1

Fig. 3

Sleeve

with Red

Trim

Fig. 4

Sleeve

with Red

Trim

Fig. 6

6. Rotate all six Leg Poles upright and insert

pin on each web loop at the side locations as shown. (Fig. 7 & 7A)

Metal Tip

Sleeve

Window Pole

Hole in

Leg Pole

Fig. 7

6. Assemble the two, shock-corded, black Window Poles, then

insert one into sleeve located at each end of tent. (Fig. 7 & 7B)

7. Insert tapered metal tip on Window Pole into Leg Pole. NOTE: It may be necessary to gently rotate Leg Pole so the

hole will line up with the Window Pole.

8. Go to opposite end of each window pole and gradually apply pressure to the pole forming an arch. Insert the pin into the leg pole end at the corners of tent. (Fig. 7 & 7C)

9. Locate the plastic hooks at sides and corners of tent, then snap onto Leg Poles to attach. (Fig. 8)

10. Locate web strap with plastic hook on the sides of each end panel Window

Fig. 8

Fig. 9

Corner

Leg

Pole

Vent, then snap onto the corner Leg Pole. (Fig. 9)

11. To stretch tent to finished size:

Window Vent

Web Tent Strap

Fig. 10

• Push in button on Leg Pole while

twisting lower Leg Pole section counterclockwise (Fig.10);

• Pull up on top Leg Pole section until

tent is taut;

• Twist the lower Leg Pole clockwise

until the button locks into the center

or lowest hole;

Upper Leg Pole Section

Button

Center Hole Lower Hole

Lower Leg Pole Section

• Repeat on remaining Leg Poles.

12. Insert plastic stakes through web straps located on both sides of tent, then drive in to secure. (Fig. 11)

Fig. 11

Hinged, Rigid Door

1. Assemble Vertical Door Pole (shorter

Sleeve

Fig. 12

black pole with plastic cap tips); then insert through zippered sleeve on side of door and into hinge. (Fig. 12)

Hinge

(continued on other side)

Hinged, Rigid Door

(continued)

2. Insert end of Vertical Door Pole into

bottom hinge plate, apply pressure to form a slight bow, then insert other tip of pole into top hinge. Zip up vertical sleeve. (Fig. 13 & 14)

3. Assemble Door Pole (longer black pole

with plastic cap tips); then insert into zippered sleeve at top of door. (Fig. 15)

4. Insert end of Door Pole into top hinge

plate, apply pressure to form a bow, then insert other tip of pole into the bottom hinge. (Fig. 16)

5. Zip up sleeve to enclose Door Pole.

(Fig. 17)

Pole Sleeve

Fig. 17

To Attach Rainfly

1. Drape Rainfly over tent. Make sure seams on Rainfly are

facing down and centered over poles of the tent. (Fig. 18) NOTE: Hook and loop fasteners, located on seams of under side of rainfly, should be centered over black and gray poles.

Rainfly

Fig. 13

Fig. 14

Pole

Sleeve

Fig. 15

Fig. 16

Attaching Room Divider

1. Divider Panel can be installed through

center of the tent by inserting toggles through the top and bottom

Top Fabric Loops

fabric loops as shown. (Fig. 23 & 24)

Fig. 23

Electrical Cord Access

Divider

Panel

Fig. 24

Fig. 25

1. Unzip access panel in the lower

left corner of tent and bring in electrical cord. NOTE: Use only UL approved cords rated for outdoor usage. (Fig. 25)

Cooler Access

The smaller zippered opening at the side of tent is designed for added ventilation and easy access to your beverage cooler.

1. To use as a vent, unzip flap to

expose screen.

2. To use as a cooler access, unzip

other flap to make an avenue to bring beverages into tent. (Fig. 26)

Fig. 26

To Store

1. All poles and stakes must be placed in the storage bag to

prevent damage to the fabric items placed in the carry case.

2. Make sure tent is clean and dry before placing in carry case.

3. Remove rainfly, spread out on floor of tent, then unzip

door & vents before taking tent down for storage.

4. Neatly fold tent to width of pole storage bag, place on tent,

roll tightly, and place in carry case.

5. Store in a clean, dry area.

STITCH LINE

Fig. 18

2. Locate all hook & loop fasteners on underside of Rainfly and

wrap around each Leg Pole and Window Vent Pole locations. (Fig. 19)

3. Insert metal hook on elastic straps on Rainfly into the hole

on each Leg Pole. (Fig 20 & 21)

Center Leg

Fig. 19

Pole

Location

Fig. 20 Fig. 21

End Leg

Pole

Location

4. Loop ends of guylines over stakes, stretch

tight, then hammer into ground at an angle as shown. (Fig. 22 & 22A)

Guyline

22A

Fig. 22

Things You Should Know:

• Under certain conditions (cold weather, high humidity, etc.) condensa-

tion will form on the inside of your tent. Condensation is caused by water vapor from your breath, perspiration, or any wet clothing inside the tent. It is NOT LEAKAGE through the tent fabric. It can be minimized by removing wet clothing from your tent and by providing good ventilation through the tent.

• Tree limbs, tree sap, bird droppings, or moisture steadily dripping off

tree limbs can cause damage to the tent fabric and its coating resulting in leaks or loss of flame-resistant properties.

• Never store tent, even for a short period of time, without drying it

thoroughly and brushing off caked dirt. Do not pack stakes or poles inside your tent. Use a separate storage bag.

• Stakes should be removed by pulling on the stake itself. NEVER PULL ON

THE TENT TO REMOVE STAKES AS THIS COULD RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY.

• Tent poles should not be left telescoped together during storage.

• Do not leave your tent set-up for weeks at a time. Be aware that exposure

to ultraviolet rays from the sun can seriously damage material and/or cause it to become discolored.

WARNING: Keep all flame and heat sources away

from this tent fabric.

This tent meets the flammability requirements of CPAI-84. The fabric may burn if left in continuous contact with any flame source. The application of any foreign substance to the tent fabric may render the flame-resistant properties ineffective.

The Coleman Company, Inc. • 3600 N. Hydraulic • Wichita, Kansas 67219

Coleman

1-800-835-3278 • www.coleman.com

MADE IN CHINA • PRINTED IN CHINA

, , , and Weathermaster®are registered trademarks of

The Coleman Company, Inc.

4010004006 (20081009)