Coleman 2000001597 User Manual

WEATHERMASTER

Before you begin

Read all instructions before set up.

• Select a level site clear of rocks, branches, and other hard or sharp objects, to install your tent.

WARNING: Keep clear of overhead power lines

• Do not set up your tent under trees because of potential lightning strikes or falling tree limbs in inclement weather.

• Secure with all

stakes and guylines provided to prevent property damage

or personal injury.

• For best results in windy conditions, position narrow end of tent into the wind.

• Enlist the help of at least one other person to assist you when it is time to assemble the tent.

Pole Descriptions

Description Qty. Dia. Repair Kit Replacement Kit

Long Leg Pole, steel

(w/ red marking) 4 19mm N/A 5010000608

Short Leg Pole, steel 4 19mm N/A 5010000610

Curved Ridge Pole, steel

(w/ red marking) 2 19mm N/A 5010000607

Curved Ridge Pole, steel 2 19mm N/A 5010000609

Awning Pole, black,

fiberglass, metal tips 1 6.3mm 5010000543 5010000545

Door Pole, long, thin, black,

fiberglass, rubber tips 1 6.3mm 5010000543 5010000545

Vert. Door Pole, short, black,

fiberglass, rubber tips 1 6.3mm 5010000543 5010000545

Pole Pole Pole

To Set Up Tent

1. Unfold tent and spread out on a clean, level surface with the

door facing the desired direction. Unzip doors. (Fig. 1)

Fig. 1

6 SCREENED TENT

MODEL 2000001597

6. Rotate all eight Leg Poles upright and insert

pin on each web loop at the side locations as shown. (Fig. 7 & 7A)

7. Locate the plastic hooks at sides and

corners of tent, then snap onto Leg Poles to attach. (Fig. 8)

8. To stretch tent to finished size:

• Push in button on Leg Pole while twisting lower Leg Pole section counterclockwise (Fig.9);

• Pull up on top Leg Pole section until tent is taut;

• Twist the lower Leg Pole clockwise until the button locks into the center or lowest hole;

• Repeat on remaining Leg Poles.

Fig. 7

Fig. 8

Fig. 9

Upper Leg Pole Section

Button

Center Hole Lower Hole

Lower Leg Pole Section

STITCH LINE

Door

2. Pull four corners of tent taut, then secure by

driving stakes through web loops at an angle for better anchoring. (Fig. 2)

3. Assemble four, steel, shock-corded,

curved Ridge Poles. Insert Ridge Poles (with red marking) into center sleeves

Ridge Pole

with Red

Marking

on top of tent with the red trim (Fig. 3). Insert the remaining curved Ridge Poles into the other two sleeves on top of tent.

4. Assemble eight, steel, shock-corded, Leg Poles. Push down

on steel button on tapered end and insert into end with four holes. NOTE: Make sure steel button locks into third hole on pole as shown. (Fig.4)

5. Insert curved end of Leg Poles

(with red marking) into the ends of the Ridge Poles (with red marking). Insert curved

Ridge Pole with

Red Marking

end of remaining short Leg Poles into the ends of the remaining Ridge Poles. (Fig. 5 & 6)

Fig. 5

Curved End of Long Leg Pole

Fig. 2

Fig. 3

Sleeve

with Red

Trim

Button in third hole

Fig. 4

Sleeve

with Red

Trim

9. Insert plastic stakes through web

straps located on both sides of tent, then drive in to secure. (Fig. 10) NOTE: It may be necessary to remove metal stakes through web straps at side of tent and screen room, pull tent taut, and drive in stakes to secure.

Fig. 10

Hinged, Rigid Door

1. Assemble Vertical Door Pole (shorter black pole with plastic

cap tips); then insert through zippered vertical pole sleeveon hinged side of door. (Fig. 11)

2. Insert end of Vertical Door Pole into bottom hinge plate,

apply pressure to form a slight bow, then insert other tip of pole into top hinge. Zip up vertical pole sleeve. (Fig. 12 & 13)

3. Assemble Door Pole (longer black pole with plastic cap tips);

then insert into zippered pole sleeve at top of door. (Fig. 14)

4. Insert end of Door Pole into top hinge plate, apply pressure

to form a bow, then insert other tip of pole into the bottom hinge. (Fig. 15)

5. Zip up pole sleeve to enclose Door Pole. (Fig. 16)

Vertical Pole

Sleeve

Door Hinge

Fig. 11 Fig. 12 Fig. 13

Fig. 6

Curved Ridge

Poles with Red

Marking in

center 2 sleeves

Top

Door

Hinge

Pole

Sleeve

Fig. 14

Fig. 15

Fig. 16

(continued on other side)

To Attach Rainfly

1. Drape Rainfly over tent. Make sure seams on Rainfly are

facing down and centered over poles of the tent. (Fig. 11) NOTE: Hook and loop fasteners, located on seams of under side of Rainfly, should be centered over Ridge Poles.

Rainfly

Door

2. Assemble thin, black, shock-

corded Awning Pole with metal tips; then insert through sleeve in Rainfly above door. (Fig. 12)

3. Insert tapered metal tip on

Awning Pole into grommet located on web strap clipped to

Awning Pole

center Leg Pole. (Fig. 13)

4. Go to opposite center Leg Pole

on other side of door and gradually apply pressure to the pole forming an arch. Insert metal tip into the grommet.

5. Locate all hook & loop fasteners on

underside of Rainfly and wrap around Leg Poles and Awning Pole locations. (Fig. 14)

Grommet

Awning

Pole

Fig. 12

Sleeve

Fig. 13

Fig. 11

Sleeve

Fig. 14

Electrical Cord Access

Fig. 20

1. Unzip access panel in the lower

left corner of tent and bring in electrical cord. NOTE: Use only UL approved cords rated for outdoor usage. (Fig. 20)

Cooler Access

The smaller zippered opening at the back of tent is designed for added ventilation and easy access to your beverage cooler.

1. To use as a vent, unzip flap to expose

Fig. 21

screen. (Fig. 21)

2. To use as a cooler access, unzip

other flap to make an avenue to bring beverages into tent. (Fig. 22)

Fig. 22

Door & Window Flaps/Vents

1. For better ventilation, unzip door flaps, roll, and insert

toggle into fabric loop to secure.

2. To open back and side window vents for more ventilation,

unzip, then roll up and insert toggles through fabric loops.

To Store

1. All poles and stakes must be placed in the storage bag to

prevent damage to the fabric items placed in the carry case.

2. Make sure tent is clean and dry before placing in carry case.

3. Remove rainfly, spread out on floor of tent, then unzip

door & vents before taking tent down for storage.

4. Neatly fold tent to width of pole storage bag, place on tent,

roll tightly, and place in carry case.

5. Store in a clean, dry area.

STITCH LINE

6. Insert metal hook

on elastic straps on Rainfly into the hole on each Leg Pole. (Fig. 15 & 16)

Fig. 15

Center Leg Pole Location

End Leg

Pole

Location

7. Loop ends of guylines over stakes, stretch tight,

then hammer into ground at an angle as shown. (Fig. 17 & 17A)

Fig. 17

Attaching Room Divider

1. Divider Panel can be installed through

center of the tent by inserting toggles through the top and bottom fabric loops as shown. (Fig. 18 & 19)

Fig. 18

Top

Fabric

Loops

Divider

Panel

Guyline

17A

Fig. 16

Fig. 19

Things You Should Know:

• Under certain conditions (cold weather, high humidity, etc.) condensa-

tion will form on the inside of your tent. Condensation is caused by water vapor from your breath, perspiration, or any wet clothing inside the tent. It is NOT LEAKAGE through the tent fabric. It can be minimized by removing wet clothing from your tent and by providing good ventilation through the tent.

• Tree limbs, tree sap, bird droppings, or moisture steadily dripping off

tree limbs can cause damage to the tent fabric and its coating resulting in leaks or loss of flame-resistant properties.

• Never store tent, even for a short period of time, without drying it

thoroughly and brushing off caked dirt. Do not pack stakes or poles inside your tent. Use a separate storage bag.

• Stakes should be removed by pulling on the stake itself. NEVER PULL ON

THE TENT TO REMOVE STAKES AS THIS COULD RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY.

• Tent poles should not be left telescoped together during storage.

• Do not leave your tent set-up for weeks at a time. Be aware that exposure

to ultraviolet rays from the sun can seriously damage material and/or cause it to become discolored.

WARNING: Keep all flame and heat sources away

from this tent fabric.

This tent meets the flammability requirements of CPAI-84. The fabric may burn if left in continuous contact with any flame source. The application of any foreign substance to the tent fabric may render the flame-resistant properties ineffective.

The Coleman Company, Inc. • 3600 N. Hydraulic • Wichita, Kansas 67219

Coleman

1-800-835-3278 • www.coleman.com

MADE IN CHINA • PRINTED IN CHINA

, , , and Weathermaster®are registered trademarks of

The Coleman Company, Inc.

4010004005 (20081030)