Coleman 2000001585 User Manual

ELITE SUNDOME®6 TENT MODEL 2000001585

Before you begin

Read all instructions before set up.

• Select a level site clear of rocks, branches, and other hard or sharp objects, to install your tent.

WARNING: Keep clear of overhead power lines

• Do not set up your tent under trees because of potential lightning strikes or falling tree limbs in inclement weather.

• Secure with all

stakes and guylines provided to prevent property damage

or personal injury.

• For best results in windy conditions, position narrow end of tent into the wind.

• Enlist the help of at least one other person to assist you when it is time to assemble the tent.

Pole Descriptions

Description Qty. Dia. Repair Kit Replacement Kit

Main Poles, long, black 2 11mm 5010000539 5010000549

Rainfly Pole, black

w/metal tips 1 11mm 5010000539 5010000549

Vertical Door Pole, black,

short w/rubber tips 1 6.3mm 501000543 501000545

Door Pole, black,

long w/rubber tips 1 6.3mm 501000543 501000545

Self-Rolling Window Spring Descriptions

Color Code Description Qty. Length Replacement Part No.

Green 1 550mm 5010000626

Orange 1 670mm 5010000628

CAUTION: “Springs” may have sharp edges. Handle with care to avoid injury. Keep out of reach of children.

Pole Pole Pole

To Set Up Tent

1. Unfold tent and spread out on a clean, level surface with the door

STITCH LINE

facing the desired direction. (Fig. 1)

2. Assemble two main tent poles by interlocking the longer, black

shock-corded, poles.

3. Insert both, long, black poles through sleeves in top of tent as

shown. (Fig. 1)

Fig. 1

7. Stretch corners and sides of tent until floor is taut then hammer

stakes through loops to secure. (Fig. 3B)

Fig. 3

Door

Hinged, Rigid Door

1. Assemble Vertical Door Pole (shorter black pole with plastic tips);

then insert through zippered vertical pole sleeve on hinged side of door. (Fig. 4)

2. Insert end of Vertical Door Pole into bottom hinge plate, apply

pressure to form a slight bow, then insert other tip of pole into top hinge. Zip up vertical pole sleeve. (Fig. 5 & 6)

3. Assemble Door Pole (longer black pole with plastic cap tips); then

insert into zippered pole sleeve at top of door. (Fig. 7)

4. Insert end of Door Pole into top hinge plate, apply pressure to form

a bow, then insert other tip of pole into the bottom hinge. (Fig. 8)

5. Zip up pole sleeve to enclose Door Pole. (Fig. 9)

Vertical Pole

Sleeve

Fig. 4 Fig. 5 Fig. 6

Long, Black,

Shock-corded

Main Poles

Door

Front of Tent

4. Insert one end of each black

pole into pins in front corners of tent. (Fig. 2)

Fig. 2

5. Go to opposite end of each pole and gradually apply pressure to the

pole forming an arch. Insert the pin into the pole end at the corners of tent. (Fig. 3)

6. Attach frame clips along edges of tent to black main poles.

(Fig. 3A)

Door Hinge

Fig. 8

Fig. 9

Top

Door

Hinge

Pole

Sleeve

Fig. 7

To Attach Rainfly

1. Assemble longer interlocking shock-corded rainfly pole.

2. Unfold rainfly. Locate the sleeve, along front edge, and the hook &

loop fasteners on the underside of Rainfly.

3. Drape Rainfly over tent. Make sure the sleeve is centered over the

door and the hook & loop fasteners, on the seams on underside of the Rainfly, are positioned over the black main poles.

4. Slide rainfly pole

through sleeve at front of the Rainfly. (Fig. 10)

(continued on

other side)

Rainfly Sleeve

Door

Rainfly

Pole

Fig. 10

To Attach Rainfly continued

5. Insert metal tip of black rainfly pole into metal grommet located on

front seams of tent (Fig. 11 & 11A). Gradually apply pressure to other end of pole to form an arch & insert metal tip into grommet.

6. Attach hook & loop fasteners, located on seams of the underside of

Rainfly, around the black main poles, to secure. (Fig. 11B)

7. Clip hooks on elastic cords, on the front and

back corners of Rainfly, onto metal loops at front and back corners of tent. (Fig. 11C)

8. Stretch guylines until taut, then

secure with stakes. (Fig. 11D)

Fig. 11

Guyline

Black Main

Pole

Rainfly

Pole

Grommet

11A

Tent Lighting System

Your tent comes pre-wired with the Coleman®Tent Lighting System. See manual that came with the light and carefully read all instructions before use then save for future reference.

Electrical Cord Access

Fig. 17

1. Unzip the access panel in the lower

left corner of tent and bring in an electrical cord. NOTE: Use only UL approved cords rated for outdoor usage. (Fig. 17)

Cooler Access

The smaller zippered opening at the side of tent is designed for added ventilation and easy access to your beverage cooler.

1. To use as a vent, unzip flap to expose screen.

Fig. 18

2. To use as a cooler access, unzip other flap to

make an avenue to bring beverages into tent. (Fig. 18)

To Store

1. All “springs” must be rolled up and placed in bag with stakes.

2. All poles and stakes must

damage to the fabric items placed in the carry case.

3. Make sure tent is clean and dry before placing in carry case.

4. Remove rainfly, spread out on floor of tent, then unzip door & vents

before taking tent down for storage.

5. Neatly fold tent to width of pole storage bag, place on tent, roll

tightly, and place in carry case.

6. Store in a clean, dry area.

be placed in the storage bag to prevent

11D

11B

11C

Self-rolling Windows

CAUTION: “Springs” may have sharp edges. Handle with care to avoid injury. Keep out of reach of children. NOTE: Carefully unroll metal “springs” stored in bag with stakes. The color marking on each “spring” should match the color of the fabric “flag” sewn to the window or door sleeve opening. (Fig. 12)

1. Locate sleeve(s) in window panel, open hook & loop fastener; then

insert “spring(s)” with matching color marking. (Fig. 12 & 13) NOTE: When inserting into the sleeve(s), the color marking on the “spring(s)” should always face the operator.

2. Close hook & loop fastener to secure.

3. Before unzipping and opening the window, push in at top to engage

“spring(s)” to activate the self-rolling feature. (Fig. 14)

4. Unzip to allow the window panel to roll down automatically; zip

back to close window panel. (Fig. 15 & 16)

NOTE: Repeat steps above for inserting the color matching “spring(s)” into sleeve(s) for the rest of the windows.

Color “Flag”

Sleeve

Fig. 12

Color

“Flag”

Color

Dot

Fig. 13

Push in at top

to engage “spring(s)”

Fig. 14

STITCH LINE

Things You Should Know:

• Under certain conditions (cold weather, high humidity, etc.) condensa-

tion will form on the inside of your tent. Condensation is caused by water vapor from your breath, perspiration, or any wet clothing inside the tent. It is NOT LEAKAGE through the shelter fabric. It can be minimized by removing wet clothing from your shelter and by providing good ventilation through the tent.

• Tree limbs, tree sap, bird droppings, or moisture steadily dripping off

tree limbs can cause damage to the tent fabric and its coating resulting in leaks or loss of flame-resistant properties.

• Never store tent, even for a short period of time, without drying it

thoroughly and brushing off caked dirt. Do not pack stakes or poles inside your tent. Use a separate storage bag.

• Stakes should be removed by pulling on the stake itself. NEVER PULL ON

THE TENT TO REMOVE STAKES AS THIS COULD RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY.

• Tent poles should not be left telescoped together during storage.

• Do not leave your tent set-up for weeks at a time. Be aware that exposure

to ultraviolet rays from the sun can seriously damage material and/or cause it to become discolored.

WARNING: Keep all flame and heat sources away

from this shelter fabric.

This shelter meets the flammability requirements of CPAI-84. The fabric may burn if left in continuous contact with any flame source. The application of any foreign substance to the tent fabric may render the flame-resistant properties ineffective.

Window Panel

Sleeves

Fig. 15

Fig. 16

Door

Window

Panel

CAUTION: All “springs” must be removed from sleeves before tearing

down tent to avoid damage to the tent fabric or part. To avoid injury, carefully roll up “springs”. Keep out of reach of children. Store rolled “springs” in bag with stakes.

The Coleman Company, Inc. • 3600 N. Hydraulic • Wichita, Kansas 67219

Coleman

1-800-835-3278 • www.coleman.com

MADE IN CHINA • PRINTED IN CHINA

, , , and Sundome®are registered trademarks of

The Coleman Company, Inc.

4010003992 (20080928)