Coleman 2000001105 User Manual

4. Insert one end of each

black pole into pins in front corners of tent. (Fig. 2)

5. Go to opposite end of

each pole and gradually apply pressure to the pole forming an arch. Insert the pin into the pole end at the corners of tent. (Fig. 3)

6. Attach frame clips along

edges of tent to black main poles. (Fig. 3A)

7. Stretch corners and sides

of tent until floor is taut then hammer stakes through loops to secure. (Fig. 3B)

STITCH LINE

LONG FLY SUNDOME 10’ X 10’

MODEL 2000001105

Before you begin

Read all instructions before set up.

• Select a level campsite clear of rocks, branches, and other hard or sharp objects, to install your tent.

WARNING: Keep clear of overhead power lines.

• Do not set up your tent under trees.

• For best results in windy conditions, position end of tent into the wind.

• Enlist the help of at least one other person to assist you when it is time to assemble the tent.

Fig. 2

To Set Up Tent

1. Unfold tent and spread out on a clean,

level surface with the door facing the desired direction. (Fig. 1)

2. Assemble two main tent poles by inter-

locking the longer, black shock-corded, poles.

3. Insert both, long, black poles through

sleeves in top of tent as shown. (Fig. 1)

Fig. 3

Parts and Components

Description Part Number

Main Poles, Long, Black (2) 5010000380

Ridge Pole w/rubber tips, Black (1) 5010000381

Rainfly 5010000376

1. Assemble the black interlocking shock-corded ridge pole with

rubber tips.

2. Unfold rainfly. Locate the web pockets on front and back of rainfly,

and the hook & loop fasteners on the underside of rainfly.

3. Insert rubber-tipped ends of ridge pole into web pockets located

on both sides of underside of the rainfly. (Fig. 4)

4. Locate hook & loop fasteners on the rainfly

and wrap around black ridge pole to secure. (Fig. 4A)

To Attach Rainfly

(continued on other side)

Fig. 1

Door

Long, Black,

Shock-corded

Main Poles

Web

Pocket

Black Ridge Pole

Fig. 4

Black Ridge

Pole

The Coleman Company, Inc. • 3600 N. Hydraulic • Wichita, Kansas 67219

1-800-835-3278 • www.coleman.com

MADE IN CHINA • PRINTED IN CHINA

Coleman

and are registered trademarks of The Coleman Company, Inc.

STITCH LINE

To Attach Rainfly continued

To Store

1. All metal poles and stakes must be placed in the storage

bag to prevent damage to the fabric items placed in the carry case.

2. Make sure tent is clean and dry before placing in carry case.

3. Remove rainfly, spread out on floor of tent, then unzip

door & vents before taking tent down for storage.

4. Neatly fold tent to width of pole storage bag, place on tent,

roll tightly, and place in carry case.

5. Store in a clean, dry area.

12/07

5. Turn rainfly over and drape over tent

making sure ridge pole is centered over the door. (Fig. 5) NOTE: When positioned properly, seams on rainfly will always align with poles on tent.

6. Attach hook & loop fasteners,

located on seams of the underside of rainfly, around the black main poles, to secure. (Fig. 5A)

7. Clip hooks on elastic cords, on the

front and back corners of rainfly, onto metal loops at front and back corners of tent. (Fig. 5B)

8. Tie guylines through loops on web

straps on the rainfly. (Fig. 5C)

9. Stretch guylines until taut, then secure

with stakes. (Fig. 5D)

Things You Should Know:

• Under certain conditions (cold weather, high humidity, etc.) condensa-

tion will form on the inside of your tent. Condensation is caused by water vapor from your breath, perspiration, or any wet clothing inside the tent. It is NOT LEAKAGE through the tent fabric. It can be minimized by removing wet clothing from your tent and by providing good ventilation through the tent.

• Never store tent, even for a short period of time, without drying it

thoroughly and brushing off caked dirt. Do not pack stakes or poles inside your tent. Use a separate storage bag.

• STAKES SHOULD BE REMOVED BY PULLING ON THE STAKE ITSELF.

NEVER PULL ON THE TENT TO REMOVE STAKE.

• TENT POLES SHOULD NOT BE LEFT TELESCOPED TOGETHER

DURING STORAGE.

• Do not leave your tent set-up for weeks at a time. Be aware that exposure

to ultraviolet rays from the sun can seriously damage material and/or cause it to become discolored.

WARNING: Keep all flame and heat sources away

from this tent fabric.

This tent meets the flammability requirements of CPAI-84. The fabric may burn if left in continuous contact with any flame source. The application of any foreign substance to the tent fabric may render the flame-resistant properties ineffective.

Electrical Cord Access

1. Unzip access panel in the lower

right corner of tent and bring in electrical cord. Use only UL approved cords that are rated for outdoor usage. (Fig. 8)

Fig. 8

Fig. 5

Cooler Access

The smaller zippered opening at the rear of the tent is designed for added ventilation and easy access to your beverage cooler.

1. To use as a vent, unzip flap to

expose screen. (Fig. 6)

2. To use as a cooler access, unzip

other flap to make an avenue to bring beverages into the tent. (Fig. 7)

Fig. 6

Fig. 7

Black Main

Pole