Coleman 2000000583 User Manual 2

NOTE: Make sure tab on each

pole locks into slot on bottom of Hub. (Fig. 5)

OASIS

CABIN TENT MODEL 2000000583

STITCH LINE

Fig. 1

To Set Up Tent

1. Unfold tent and spread out on a clean, level surface with the

door facing the desired direction. Unzip doors. (Fig. 1)

4. Insert end of first Short Ridge Pole (with

dot) into flange with a dot on Hub (Fig. 3). Repeat for remaining Short Ridge Pole on opposite flange of Hub with a dot.

NOTE: When installed properly, the loop on

the bottom of the Hub will be parallel two Short Ridge Poles.

5. Insert four remaining Long Ridge Poles into Hub. (Fig. 4)

7. Insert curved end of four Short

Leg Poles into the four Long Ridge Poles on top of tent. (Fig. 7)

NOTE: Make sure tab on each Long

Ridge Pole locks into slot on each Short Leg Pole.

9. Raise tent by assembling shock-corded sections of each

Long and Short Leg Pole and inserting into curved ends of Leg Poles. (Fig. 9)

10. Insert pin on loop at

each corner and the front and back of tent into all six Leg Poles. (Fig. 10)

11. Locate both plastic hooks at each corner,

and front and back of tent, then snap onto Leg Poles to attach. (Fig. 11)

12. Drive stakes through rings, located on

four corners and front and back of tent, at an angle for better anchoring. (Fig. 12)

Before you begin

Read all instructions before set up.

• Select a level campsite clear of rocks, branches, and other hard or sharp objects, to install your tent.

WARNING: Keep clear of overhead power lines.

• Do not set up your tent under trees.

• For best results in windy conditions, position end of tent into the wind.

• Enlist the help of at least one other person to assist you when it is time to assemble the tent.

2. Insert the two Short Ridge Poles (with sticker dots) into the

sleeves (perpendicular to door) on top of tent. (Fig. 2)

3. Assemble four, shock-

corded, Long Ridge Poles and insert into the four diagonal corner sleeves. (Fig. 2)

Fig. 2

2 Short Ridge Poles with Dots

4 Long Ridge Poles

Short Ridge

Pole with

Dot

Hub

Fig. 3

Fig. 4

Tab

Tab on

Pole

Hub

Fig. 5

Slot

Tab

Locked

Fig. 7

8. Insert curved end of two Long Leg Poles (with dots) into the

Short Ridge Poles at front & back of tent. (Fig. 8)

NOTE: Make sure tab on each Short Ridge Pole locks into slot

on each Long Leg Pole.

Fig. 8

Short Leg Poles

Long Leg Pole

(with Dots)

Long Leg Pole (with Dots)

Fig. 9

Fig. 10

6. Snap hook at top of tent onto metal loop

on bottom of Hub. (Fig. 6)

Fig. 6

Fig. 11

To Attach Rainfly

1. Drape Rainfly over

tent. Make sure seams on Rainfly are facing down with web pockets and long straps centered over doors & back of tent. (Fig. 13)

Fig. 13

2. Locate and wrap hook and

loop fasteners, on underside of Rainfly, and wrap around the Leg Poles to secure. (Fig. 14)

Fig. 14

(continued on other side)

Parts and Components

Description Part Number

Hub (1) 5010000120

Short Ridge Pole (2) 5010000121

Long Leg Pole (2) 5010000122

Short Leg Pole (4) 5010000123

Long Ridge Pole (4) 5010000124

Awning Pole (2) 5010000125

Rainfly (1) 5010000126

Hub (1)

Short Ridge Poles (2)

Long Ridge

Poles (4)

Long Leg Poles (2)

Awning Poles (2)

Short Leg

Poles (4)

(Front of Tent)

Rainfly

Long Strap

Pin & Loop on web tent strap

Hook and Loop

Fastener

Doors

Fig. 12

To Attach Rainfly continued

3. Insert end of Awning Pole with plastic tip into web pocket at

front of the Rainfly. (Fig 15)

4. Insert metal tip on Awning Pole into hole in Long Leg Pole (Fig 16). NOTE: It may be necessary to rotate the pole slightly for proper alignment with Awning Pole.

5. Install remaining Awning Pole at back of tent as shown in steps 3 & 4 above. (Fig. 15 & 16)

6. Insert hooks on elastic straps, located at corners of Rainfly, into holes on the four Short Leg Poles to secure. (Fig. 17)

7. Insert hooks on long elastic straps, located at front and back of Rainfly, into holes on Long Leg Poles to secure. (Fig. 18)

Cooler Access

The smaller zippered opening at the side of tent is designed for added ventilation and easy access to your beverage cooler.

1. To use as a vent, unzip flap to expose

screen. (Fig. 26)

2. To use as a cooler access, unzip

other flap to make an avenue to bring beverages into tent. (Fig. 27)

STITCH LINE

Attaching Room Divider

1. Divider Panel can be installed through center of the tent by inserting toggles through the top and bottom fabric loops as shown. (Fig. 22 & 23)

The Coleman Company, Inc. • 3600 N. Hydraulic • Wichita, Kansas 67219

1-800-835-3278 • www.coleman.com

MADE IN CHINA • PRINTED IN CHINA

Coleman

and are registered trademarks of The Coleman Company, Inc.

Things You Should Know:

• Under certain conditions (cold weather, high humidity, etc.) condensa-

tion will form on the inside of your tent. Condensation is caused by water vapor from your breath, perspiration, or any wet clothing inside the tent. It is NOT LEAKAGE through the tent fabric. It can be minimized by removing wet clothing from your tent and by providing good ventilation through the tent.

• Never store tent, even for a short period of time, without drying it

thoroughly and brushing off caked dirt. Do not pack stakes or poles inside your tent. Use a separate storage bag.

• STAKES SHOULD BE REMOVED BY PULLING ON THE STAKE ITSELF.

NEVER PULL ON THE TENT TO REMOVE STAKE.

• TENT POLES SHOULD NOT BE LEFT TELESCOPED TOGETHER

DURING STORAGE.

• Do not leave your tent set-up for weeks at a time. Be aware that exposure

to ultraviolet rays from the sun can seriously damage material and/or cause it to become discolored.

WARNING: Keep all flame and heat sources away

from this tent fabric.

This tent meets the flammability requirements of CPAI-84. The fabric may burn if left in continuous contact with any flame source. The application of any foreign substance to the tent fabric may render the flame-resistant properties ineffective.

To Store

1. All metal poles and stakes must be placed in the storage

bag to prevent damage to the fabric items placed in the carry case.

2. Make sure tent is clean and dry before placing in carry case.

3. Remove rainfly, spread out on floor of tent, then unzip

door & vents before taking tent down for storage.

4. Neatly fold tent to width of pole

storage bag, place on tent, roll tightly, and place in carry case.

5. Use wheels on bottom of carry

case and web handle for easy transporting of the tent. (Fig. 28)

6. Store in a clean, dry area.

Electrical Cord Access

1. Unzip access panel in the lower

left corner of tent and bring in electrical cord.

NOTE: Use only UL approved cords

rated for outdoor usage. (Fig. 25)

Rev 01/08

Overhead Storage

1. Hang the overhead storage panel by placing the hooks through the loops on the inside of the tent. (Fig. 24)

NOTE: The overhead storage is to keep

small items off the floor. Large or heavy items may damage the tent.

Fig. 15 Fig. 16

Fig. 17

Fig. 18

8. Tie guylines onto the six web loops located on the sides of the Rainfly. (Fig. 19 & 21)

9. Loop end of guyline over stake, stretch tight, then hammer into ground at an angle as shown. (Fig. 20 & 21)

10. Secure door mat through loops with stakes. (Fig. 21)

Fig. 19

Fig. 20

Fig. 21

Fig. 22

Fig. 23

Fig. 24

Hook on Storage

Panel

Tent Loop

Fig. 27

Fig. 26

Fig. 28

Door & Window Flaps/Vents

1. For better ventilation, unzip door flaps, roll, and insert

toggle into fabric loop to secure.

2. To open back and side window vents for more ventilation,

unzip, then roll up and insert toggles through fabric loops.

Fig. 25

Door Mat

Divider

Panel

Pockets for

Gear Storage

Web Loop

Guyline