Coef EMULATION CTC User Manual
OPERATION MANUAL
EMULATION CTC
Document No: OM-L2010-001-R01
COEF EMULATION CTC
TABLE OF CONTENTS
GENERAL NOTES
DECLARATION OF CE CONFORMITY ------------------------------------------------------------------------------------------------------ 3
ADVICES FOR A CORRECT INSTALLATION----------------------------------------------------------------------------------------------3
GENERAL WARRANTY CONDITIONS------------------------------------------------------------------------------------------------------- 4
PACKING CONTENTS---------------------------------------------------------------------------------------------------------------------------- 4
WIRING BASICS------------------------------------------------------------------------------------------------------------------------------------ 4
1. INTRODUCTION -------------------------------------------------------------------------------------------------------------------------------- 5
2. OPERATION-------------------------------------------------------------------------------------------------------------------------------------- 5
2.1 DMX TABLE ----------------------------------------------------------------------------------------------------------------------------- 6
2.2 BACK PANEL --------------------------------------------------------------------------------------------------------------------------- 6
2.3 MENU STRUCTURE ------------------------------------------------------------------------------------------------------------------ 7
3. APPLICATIONS EXAMPLE ------------------------------------------------------------------------------------------------------------------ 8
3.1 MANUAL DMX ADDRESSING ----------------------------------------------------------------------------------------------------- 8
3.2 AUTO ID (DMX) ADDRESSING---------------------------------------------------------------------------------------------------- 8
3.3 MANUAL DMX AND AUTO ID ADDRESSING I-------------------------------------------------------------------------------- 8
3.4 MANUAL DMX AND AUTO ID ADDRESSING II------------------------------------------------------------------------------- 8
4. TROUBLESHOOTING ------------------------------------------------------------------------------------------------------------------------- 9
5. TECHNICAL SPECIFICATIONS ------------------------------------------------------------------------------------------------------------ 9
PAGE 2
COEF EMULATION CTC
DECLARATION OF CE CONFORMITY
We Manufacturer IAG Sanecore Science & Technology Industry Park, Jiuwei Village, Xixiang Town, Shenzhen, China,
518102 Declare that the product EMULATION CTC is in conformity with 89/336 EEC-EMC directive and with the actual
required safety standards in accordance with LVD 73/23 EEC
Shenzhen, 01 August 2010
ATTENTION: carefully read the directions of this manual. Exclusively follow the safety rules in force and do not carry
out assembly and/or maintenance operations without taking all precautions as indicated in the different sections or without the necessary specialization.
This manual must always accompany the equipment, therefore it must be available and readable at any moment if necessary. Also in case of sale, rent, change of place and/or ownership, these documents shall be enclosed with the relative equipment.
ADVICES FOR A CORRECT INSTALLATION
This equipment is designed to an exclusively Professional use.
1) Make sure that all the fastening parts of the spotlight are in good condition. Regulate the proportions of the fastening accessories (screws, bushes, nuts, supports, etc.) in order to be slightly over-dimensioned as compared to the
actual requirements.
2) The installation must always be secured with a secondary safety attachment, e.g. an appropriate catch net. The
secondary safety attachment must be constructed in a way that no part of the installation can fall down if the main
attachment fails.
3) Carefully check the contents of the packaging and the completeness of the components. If any of the parts listed
hereunder is missing, please contact your Dealer immediately.
4) Do not install the projector outside where the influence of atmospheric factors could damage the unit working
(rain, wind, intense heat etc.) or indoor if there is a high percentage of humidity.
5) Do not clean the projector using water jets or immersion in different liquids. Scrupulously follow the indications
given in the chapter MAINTENANCE.
6) Make the electric connections and the installation / replacement of the lamp after having disconnected the power
supply and after had positioned the power switch to OFF. The apparatus is classified as belonging to Class 1 type
of protection against electric shocks. Its connection to an earthed mains unit is compulsory. The equipment must
be protect by an degusted magneto-thermal switch. You are recommended to equip the system with aptly dimensioned differential switches.
7) Do not touch in any case the internal and external parts of the projector without previous authorization of the constructor and make modifications only by the intervention of qualified staff.
8) If the bulb explodes, the particular design of the apparatus prevents the splinters from going outside the projector.
All the parts, therefore, shall be complete and perfectly assembled. The lenses, if visibly damaged, shall be replaced by original spare parts.
9) Minimum distance from illuminated objects:
by the light beam are located at least 1 meters from the projector objective.
10) Minimum distance from inflammable materials: 0.5 meters
The projector must be positioned in such a way that objects struck
PAGE 3
COEF EMULATION CTC
11) MAX ambient temperature: 60° C.
12) MAX external surface temperature:
13) Don’t look directly the lamp trough the lens.
14) We recommend not to look at the lamp without wearing a proper protection; also ensure that the covers are assembled to the equipment.
15) Inside the equipment there are high temperatures and tension/current values which might be very dangerous. It is
necessary to disconnect the equipment from the mains before removing its protection covers and wait for 30 minutes at least before touching any part inside.
16) Do not switch on the equipment if its lamp is not inserted.
17) Leave sockets and air outlets free from encumbrances and clean them periodically (see “Maintenance” section).
18) Do not leave the packaging elements (polystyrene, nylon, metal parts, etc.) unattended; they might be dangerous
for children.
This manual has been organized in order support the user, the installer or the maintenance operator of the described
unit with those necessary in formations for a correct use of the installation and working procedures of the same unit.
The various procedures will be just signaled by indicators (when necessary) evidencing the operation dangers and the
necessity of technical support.
60° C.
GENERAL WARRANTY CONDITIONS
• The guarantee is valid for a period of 12 months from the date of equipment delivery.
• The guarantee is not valid in case a wrong voltage or frequency is selected.
• The parts which are proved to have manufacturing defects are also covered by the guarantee.
• The external parts of the equipment, its removable elements and lamps are excluded from the guarantee; for
these parts we recommend to follow the directions supplied by their manufacturers.
• The guarantee is not valid in case of tampering or repairs carried out by non-authorized personnel.
• The replacement of the equipment during the validity of the guarantee is not provided for.
• The transport freights from and to the manufacturer for repairs under guarantee are at Customer’s charge.
• When applying for the repair, always mention the serial number and the model of the equipment.
PACKING CONTENTS
• Complete EMULATION CTC unit
• This user manual
• 1 AC Power cord
WIRING BASICS
Connection with the mains
Connect the device to them mains with the power plug. The occupation of the connection cables as follows:
European Standard
Cable Pin International
Brown Live L
Blue Neutral N
Yellow Earth E
Cable Pin International
Black Live L
White Neutral N
Green Earth G
American Standard
∗ The earth must be connected !
PAGE 4
Loading...