CODELOCKS KitLock KL1O Installation And Operating Instructions Manual

KL1O

Installation and Operating Instructions

SPECIAL NOTES

Please read carefully:

• Before installing the lock, familiarise yourself with the installation and operating instructions.

• The factory preset combination is 0-0-0-0.

• Your KitLock is supplied ready to t to doors up to 19mm (

FITTING INSTRUCTIONS

The KitLock can be tted to cabinets, cupboards and lockers etc. as a direct replacement for existing cam locks.
It can also be tted easily to cupboards and cabinets that do not have an existing locking device.

3

/4”) thick.

Fixing Pack A Default Supply

1

KitLock

2

Hex nut x 1

1.

3

Straight cam x 1

4

Screw x 1

3.

2.

4.

INSTALLATION GUIDE

Replace existing cam lock with KitLock

A

Step 1 Remove existing cam lock.

Step 2 Fit the KitLock to the door, passing the

spindle through the existing hole.

Step 3 Now secure the lock by threading the hex nut

onto the spindle.

Step 4 Fit cam and secure with screw.

Step 5 Now check the operation of the lock using the

factory preset combination 0-0-0-0.

Fixing Pack B Optional Additional Fixings

1

Metal Clip x 1

2

Screws x 2

2.

1.

New Installation

B

N.B. Optional Fixing Pack B (above) may be required.

Step 1 Mark a position at a suitable distance from

the door edge, ensuring enough clearance
for the cam to work.

Step 2 Using the ‘Typical Door Prep.’ dimensions

(see overleaf), drill a hole to suit..

Step 3 Continue installation from step 2 to 6, left.

3

Washer x 1

4

Crank Cam x 1

3.

4.

Step 6 If the lock is functioning correctly, change the

code using the instructions overleaf.

CHANGING THE CODE

HOW TO USE YOUR LOCK

1

With the indicator in the open position, turn the dials
to the factory preset combination 0-0-0-0.

Note: If you have already changed the code, use

your current combination for this step.

2

Depress the reset button fully and hold, turn the dials
to your desired combination.
Note: Do not let go of the reset button while setting
your combination.

3

Release the reset button after checking your

combination is correct.
Note: The outer casing will turn freely between the
open and locked position until the combination has
been scrambled.

FINDING THE CODE

Note This function requires the Master Key (sold separately).

1

Insert the master key
when the indicator is in
the locked position.

3

Gently rotate each dial
upwards until it stops.
This is your code.

2

Turn the key

clockwise 90

degrees.

4

Turn the master key

anticlockwise 90
degrees and remove.

1

Once you have chosen and set your

combination, turn the outer casing so the
indicator is in the locked position.

2

Make a note of your chosen combination and

scramble the dials. The lock is now locked.

3

To reopen, rotate the dials to your chosen
combination and turn the outer casing so the
indicator is in the open position.
Note: Your chosen combination will continue to
operate the lock until it is changed.

Indicator

Reset Button

Open Position

Dials

Guide line

Master key

Locked position

DIMENSIONS

KL10

CODELOCKS UK
HEADQUARTERS

Tel: [phone]
Fax: [phone]

[e-mail]
www.codelocks.com

Helpline, service & spares
Freephone: 0800 393 405

IOI-KL10-v1-0119

58mm

(2 5/

”)

16

24mm

(15/

”)

16

CODELOCKS INC US

Tel: [phone]
Fax: [phone]

[e-mail]
www.codelocks.us

Helpline, service & spares
Toll free: 1.877.codelock

62mm (2 1/2 ”)

52mm (2 1/16”)

CODELOCKS
(Australia) PTY LTD

Tel: [phone]
Fax: [phone]

[e-mail]
www.codelocks.com.au

Helpline, service & spares
Toll free: 1800 052 131

18mm
(11/

16

max.

Typical Door Prep.

19mm (3/4 ”)

25mm

(1 ”)

”)

min.

16mm

(5/8 ”)

min.