CODELOCKS 4OOO ELECTRONIC, 5OOO ELECTRONIC, 4010, 4020, 5010 Installation Instructions Manual

INSTALLATION INSTRUCTIONS

4OOO

ELECTRONIC

5OOO

ELECTRONIC

4000/5000 manual_Layout 1 14/01/2013 15:53 Page 1

•Power Drill

• Drill bits 5010
10 (3/8”) & 25mm (1”)

• Drill bits 5020
10 (3/8”), 12 (15/32”), 16 (5/8”) & 20mm (25/32”)

• Hammer / mallet

Box Contents

Check the contents of the box are
correct according to the model

Tools Required

• Philips screwdriver

• Chisel 25mm (1”)

• Stanley knife

• Adhesive tape, pencil, bradawl, Tape measure

• Pliers and hacksaw for cutting bolts

4OOO

5OOO

2

4010 4020 5010 5010BB 5020

1 Front Plate 4000 33 ---

2 Front Plate 5000 --3 x2 3

3 Back Plate 4000 33 ---

4 Back Plate 5000 --3 - 3

5 Back to Back Fixing Plates ---3 -

6 Lever Handles 4/5000 33333

7 Gaskets (x2) 33333

8 Sprung Spindle 3 - 33 -

9 Sprung Spindles (x3) – 15/26/60mm (

1

/2”/ 11/32”/ 23/8”) - 3 --3

10 1.5v AA Batteries (x4), (5010BB 8 x 1.5v AAA) 33333

11 Mortice Latch, Strike and 4 screws 3 - 33 -

12 Fixing Bolts (Inc spare) x3 x3 x4 x4 x4

13 Cable Tube and Ring Nut --3 --

14 Alignment Insert --3 --

15 Latch Support Post 3 - 33 -

16 Allen Keys 33333

17 Cable Connections for REM1 and REM2 33333

18 Front Plate Cylinder Keys 33333

19 Front Plate Cylinder Cover 33333

20 Classroom Function Tailpiece 33333

21 Mortice Lock & Cylinder for 4020/5020 - 3 --3

This box should also contain an Installation Template and Programming and Operating Instructions.

4000/5000 manual_Layout 1 14/01/2013 15:53 Page 2

3

21

4000/5000 manual_Layout 1 14/01/2013 15:53 Page 3

You should familiarise yourself with the operation of the lock and
check that all parts work properly.

Remove the battery cover from the back plate and install the 4 x AA
cells supplied.

Connect the cables from the front plate and back plate. A BLEEP
should be heard when you do this. If no BLEEP is heard then check
that the batteries are correctly installed.

Place the long spindle in the front plate socket and using finger grip
only, test that the spindle is easily moved 80

o

in both directions.

Leave socket in the centred position.

Enter the factory Master Code (#1234 for the CL5000) (Badge Bar
1234 for the CL4000).
N.B. When the Master Code is entered 3 times consecutively
without performing a programming function, a penalty time of 10
seconds is activated.

The Blue light should flash and the spindle should not turn as
before. After 5 seconds the Red light should flash and the spindle
should turn easily again. This confirms that the clutch engaged
correctly when the code was entered.

Disconnect the cables.

Turn the key in the front plate cylinder 90

o

clockwise and confirm

that the spindle will not turn with the key in this position.
Remove the key and confirm that the spindle again turns easily.
This confirms that the key bypass function operates correctly.

For the CL4020 and the CL5020 locks see page 10 to check the
operation of the mortice lock.

REMOTE RELEASE OPTION

Cables are provided for the REM 1 and REM 2 terminals on the
circuit board. (Fig 1 below).

OPERATIONS CHECK SPECIAL FIXING NOTE

REM 1 is for connection to a reception desk push button or a door
intercom system. Pressing the button will cause the Blue light to
flash on the lock and release the lock for the pre-set time.

REM 2 is for connection to the building alarm system to release a
door in an emergency. This allows rooms, wards, offices to be
easily checked to ensure that no person is trapped or overlooked
during an emergency evacuation. When activated REM 2 will
maintain the unlocked condition for 30 minutes, the Red LED will
flash and BLEEP during this time.

The lock will automatically lock again after 30 minutes. If
necessary Program 11 can be used to re-lock before the end of the
30 minutes.

REM 1 and REM 2 do not require additional power.They are
normally open contacts requiring a momentary or maintained
signal to close.

1. Battery

2. Remote 1

3. Remote 2

4. Clutch/Actuator

4

4000/5000 manual_Layout 1 14/01/2013 15:53 Page 4