Code Alarm TW-1 Owner's Manual

Page 1
Cccc~l.Ar:lm·
Technology
that
talks
to
cars
and
Remote Vehicle
Control
System
Two
Way Remote Start
)
IMPORTANT
manual
and configuration
ANDIOR
Installing dealer for more informallon.
NOTE:
Is
applicable
SAFETY
The
opsr<!.tion
vehicles.
of
may
to
most
of
some vehicles (l.e. diesel engines). sO(lle functions
PRECAUTIONS
& Security
the
TW-1
as
However.
not
apply.
described
due
Please
to the
engine
see
in
your
this
type
)
101513-0
Page 2
)
TABLE OF CONTENTS
Users' Precaution
The remote LCD icons with functions ................................................................ 1-2
Operation guide of
Pre-assigned function modes by remote's buttons .............................................. .4
Programmed function modes by a short press of button [ I ] ........................... .4
Self-defined functions by a short press of button
Door Lock/arm .................................................. : .................................................. 5
Defective zone bypass ......................................................................................... 5
Door unlock/disarm ............................................................................................. 6
Security diagnostic report .................................................................................... 6
Parking light flash upon door open ..................................................................... 6
Auto relock ....................
Door Lock/unlock ................................................................................................ 6
Auto door lock/unlock upon ignition on/off .......................................................... 6
Active channel
2 Steps door unlock /disarm ................................................................................ 7
Remote engine start... ....................................................................................... 7-8
Remote change of engine
Remote engine shut off ....................................................................................... 8
Remote temperature start
Remote check current auto-start temperature setting ....................................
Daily auto-start time
Remote check car indoor temperature/Status ...................................................
Active channel # 1 for release trunk ............................ · ........................................ 1 0
Remote siren/horn alert ON/OFF ........................................................................ 1 0
Active channel # 2 .................................................... : ..........................................
Car locator/search ...............................................................................................
Shock sensor by pass .........................................................................................
Alarm mode & warn away ...................................................................................
Light impact
TW1
unit ................................................................................ .4
[II]
....................................... 5
_ .................................................................................... 6
# 3 ............................................................................................... 7
run
time ..................................................................... 8
ON/OFF ..................................................................... 9
ON/OFF .............................................................................. 9
trigger.
..
...................................................................................... 12
::
... 9
10
11 11 11 11
A
Page 3
/
Heavier impact trigger ......................................................................................... 12
Door /hood /trunk open trigger ............................................................................ 12
Remote Panic ...................................................................................................... 12
Remote anti-carjack Switch-controlled anti-carjack
ON/OFF .............................................................................. 12
ON/OFF ............................................................... 13
Remote valet ON/OFF ........................................................................................ 13
Programmable function
by
over-ride switch ........................................................ 14
Page-out call ....................................................................................................... 14
Manual ARM and
DISARM ............................................................................. 14-15
Procedures of remote start for manual transmission gear car ............................ 15
How to learn codes of the remote transmitter ..................................................... 15
Dash LED status indicator ................................................................................... 16
Replacement of battery ....................................................................................... 16
Programming of remote control unit.. ..................................................................
17
B
Page 4
)
TW-1 ICONS AND FUNCTIONS
The alphabetical signs indicate the function modes
A. Remote anti-carjack mode ON/OFF
B.
Remote control channel # 3 for electrical appliance
c.
Remote activate temp-controlled auto-start mode
D.
Remote activate daily auto-start time
ON/OFF
mode
E.
Remote engine start (or) changing of run time when the engine gets
ON/OFF
ON/OFF
G. Remote activate Audible arm mode
ON/OFF
H. Remote shock sensor bypass mode
ON/OFF
I.
Remote activate valet mode ON/OFF
J.
Remote monitor in-car temperature & status
K.
Remote control channel # 2 for
electrical appliance
L. Remote trunk release
ON/OFF
)
Page 5
• The
numerical
signs
indicate
the
vehicle's
security
status
or
J
other
1.
Remote's battery condition
2.
Channel # 2 On/OFF
3.
Temp-controlled auto-start mode
4.
Engine
5.
Trunk release
6.
Door open
7. Remote unit's vibration mode
8.
Valet mode
9.
Auto rearm mode
1
O.Mute alert mode
11.Audible alert mode
12. Hood open mode
13.lmpact/shock mode
14.Hand-brake disengage
15. Door lock mode
16.Door unlock mode
17. Monitor standby mode
function
run
mode
display
18.Feedback confirmation command by remote unit; display of this confirms feedback can be picked
up
by remote means remote or feedback is being interfered.
19.Page out-call from car
20.Power current sleep 'mode of the remote, after system is disarmed)
21.lgnition On mode
22.Alarm clock mode
23.P.M time mode
24.A.M. time mode
25.Daily auto-start time mode
26.Hour, minute, temp. display
27.Centigrade, Celsius mode
28.Count-down time mode
unit.
is
either out-of- range
save mode of remote(Absolute
(Alter each
Non-display
2
Page 6
TW-1 User's manual 2 Way remote security system
• Precaution before installation
1.
Read this manual carefully ahead of operation.
versatile.
2.
Park the vehicle
you from being suffocated by the exhaust gas while the engine gets running.
3.
For safety purpose, set your car
serviced
4.
There functions that require external accessories.
5. program
Special features:
1.
features)
2.
3.
4.
5.
6.
7.
8.
9.
10.
11. Programmable for daily auto start time
12. Remote monitoring of car status lin-car temperature
13. Display
14. Display
15.
16. Remote control electrical appliances through channel # 1 ,#2 , #3
17. The main system temporarily by-passes shock sensor at the moment the remote
18.
19.
20. Remote or manual valet mode
21.
22.
are
You
are suggested to refer to the "options Program Table" whenever you find[ options
table]
Choice
2 Way Super-remote control/monitoring range [Effective range
800-1200 Electronic luminescent backlight Hopping code for anti-grabbing Main system's memory able to learn codes from 4 different remotes Remote control of lock/unlock, arm/disarm, engine start, trunk release and etc. Switch-accessed Arm/disarm for emergency Selectable mode for auto/manual transmission gear with safety circuit
Selectable rnode for gasoline and diesel engine Programmable for temp-controlled auto-start
Smart temper report by siren when disarmed
trunk release is activated Remote control & switch-activated anti-carjack modes Remote panic
Other system's functions accessible by software program LED status indicator
in
open space
many other functions ,Refer to the installation manual for such extra
in
the text
of
function
mode
each
time if the remote start
to
valet mode "ON" before sending it
on
the installation manual.
by
cursor
on screen
m]
of
defective zones bypass when arming
of
remote shock sensor bypass
to
assist programming and anti-theft warning
You
will find this product very
is
intended .This avoids
to
workshop
for
easiest operation
on
display
of
approx
(patented
3
for
Page 7
Operation guide of TW-1
This is devised for easy operation just by somel Imovable
out the cursor and then
cursor
meansj. Users can choose the desired function just by first popping
moving
it
on
to the related function Position.
fixed
functionl by buttons and
..
J
There are total 3 buttons marked with buttons are used popping out and
in
alarm function mode setting and the third
moving
of the cursor on to the desired function position.
[I
'
II
'
ill]
on
the remote unit. The [ I '
[ill]
button is used in
II]
* Pre-assigned function modes by remote's buttons
Remote's button Remote's button [ Remote's button car find.
Remote's button
panic
[I]:
[I]
[1][
Press and hold this for engine-start and shutoff
II]
: Press and hold this for trunk release.
[
II]
: Press and release both [ I ] &
II
]:
Press and hold both [ I ] & [
[II]
simultaneously for
II
]simultaneously for remote
* Programmed function modes by a short press of button [ I ]
Press and release this to activate self-defined function .It is generally programmed for
door lock/unlock. Step 1: Press button
cursor to the desired position necessary. For example, move the cursor
have
Step 2: When the cursor reaches the desired position, press and hold
sec till the remote unit sounds the first 2 and final 3 and
*
To
re-define the function of button [ I
& (2).The previously-defined function mode will be substituted
Other functions can also
[ill]
"Audible Arm
release button [
Mode"
be
programmed as
twice or more times quickly to pop up the cursor.
by
pressing button
on
to r t::;I J position, if you want to
function activated by a short press of button [ I ] .
I]
to activate the selected function.
]re-do
the procedure from procedure step
below:
[ill]
a number times as
~
beeps.
From then on, press
by
[ill]
the last definition.
Move
again for 6
the
(1)
)
4
Page 8
* Self-defined
Press and release button programmed to assign rJQJ for Mute Arm Mode. other functions programmed
as
functions
below:
by a
short
[1I]
to activate self-defined function .It
~
press
of
button
[II]
is
generally
can
also
be
Step 1 : Press button
to
cursor necessary. For example, move the cursor " Status Check" function activated by a short press
The
following 2 way
cursor
1.
I Remote arm &
(a)
, Shut off the engine, get out of the car making sure handbrake
closed and all the door closed.
(b)
, Press and release button [
with 1 siren chirp and 1 parking light flash .
• The remote unit sounds melody and displays r Q J (c)
, Press and release button
with 1 siren chirp and 1 parking light flash.
The remote unit sounds melody and displays r e
means the system (d)
, Defective zone
defective zones, the system will sound 4 siren chirps or the remote unit sounds 4 beeps twice. The remote unit displays on its screen the defective zone ( like the
door open).The system then will bypass the defective zone and can enter arm mode. When the defective zone system immediately enters full
, Arm
(e)
closed)
the desired position by pressing button
setting
delay
as
[ill]
twice or more times quickly to pop
remote's
in
the
above
door
lock
is
in
mute arm mode.
report
time
can be
needed. [option program
and bypass
programmed:
function
passage
I
I]
the system will lock the door and enter arm mode
[1I]
the system will lock the door and enter arm mode
is
corrected ( just by closing the door later
arm
up
the cursor. Move the
[ill]
a number times as
on
guide
arming:
mode.
( like 6 or 30 sec daily arming after door
table]
~
to
r\,$l:JJ , if
of
is
lr({i)jI
When arming, if the system detects
you want to have
button
[1I]
based
is
r(<<"
J icons
Jicons
on
.
on
the
depressed, hood
on
its
its screen.
screen which
current
),
the
is
5
Page 9
2.
I Remote
(a)
- Press and release the button [ disarm on
.(
The remote unit sounds 2 beeps and
(b)
- Smart zone trigger report: Should there
arm
mode, the siren sounds 4 chirps or the remote sounds 4 beeps when the remote unit's button displayed on the remote unit's screen.
(c)
- Parking light flash upon door-open: Each time the car door disarm,
[option program
(d)
-Auto rearm: This not opened after
3.
I Remote
(a)
Press and release button [ I ] while driving, the system will unlock/lock with parking
light flash.
The remote unit displays
*
You
can also program to have door lock/unlock upon ignition ON/OFF. [option
program
disarm & door
itself with 2 siren chirps and 2 car light flashes. The dome light will turn
Refer to installation manual for dome light features that needs external relay)
the parking light flashes for 10 sec
table] is
programmable to have your system rearm itself if the car door is
30
door
lock/unlock
table ]
unlock
[I]
sec from the time of remote disarm [ option program
I
I]
or
[IT]
the system will unlock the door and
displays'
is pressed. The trigged zone during arm mode
iii
~
icon
on
its
screen
be
any abnormal security status while
is
opened following
to
caution other vehicles coming behind.
I
'd
~
for the door unlock or
displays'
6
~
for door lock.
table]
in
is
6
Page 10
J
Single Option ( Choose
only
one
of
these)
I Remote
(a) , If required)
(b)
(c), Then press and release [
selected function mode .The parking light flashes 3 times for confirmation .
• The remote unit displays Car Status
I 2 stage
(a) , If
an
( (b)
control
the system is programmed for channel #3 mode (
, Press quickly
W it onto
[B3]
door
the system is programmed channel # 3 for 2 stage door unlock mode.
external accessory is required)
,
Press quickly
channel # 3 I (option program table ]
(ill]
twice or more rimes to pop
) .
IT]
.The system responses
on
its screen and sounds 3 beeps
unlock,
disarm
[ill]
I (option program table ]
twice or more times
to
an
external relay
up
cursor
pop
up the cursor and then
and
then move
in
accordance with
is
/)
move it onto (c)
, Then press and release
unlock
4,
I Remote engine
(a) , The engine is (b)'
Press and hold ( onto the engine gets started.
• The remote unit displays 2 stages (1) , In
51::
(2)' along with engine's preset
and
The remote unit displays
""
Choose one of the above two options
d;b
the column. Siren chirps 3 times with 3 parking light flashes when the
the 1
~
while engine
In
the 2
W
(B3]
)
disarm with 2 siren chirps and 2 parking light flashes.
start
I
in
shut off state.
I]
button. Or press
st
stage: The remote unit displays the current status along with
is
trying for engine start and
nd
stage: After the engine gets started, the remote unit displays
run
(
IT]
• U
~
IT
on
its screen as
tirne and
7
to unlock all the doors. The system will
on
its screen and sound 2 beeps .
and
program
button when the active cursor
below:
sounds.
sounds.
·It
as required.
is
shifted
Ii"
...
_
-
.!l
J
Page 11
(c)
, The remote start
When the preset remote unit displays
00.
displays
disappears.
(d)
, Remote engine start cannot
is
not
in
its neutral position,
Hand break is depressed
remote-started for the pre-set runtime. A maximum case of failure
of
stage
When the system fails engine start after the 41h unsuccessful start effort, the remote unit sounds 4 beeps and its
5.
I Remote change of
(a)
, After the engine gets started by the remote unit
(b)
, Press
cursor
(c)
,Press run LCD LCD rneans the current
Note:
trials,
ill
on
to the
and release
time and additional pressing
on
the remote unit displays the current
The function of
run
time can
run
time expires, the engine will automatically
'r
on
the remote unit at the moment of engine shut-off and then
of
engine-start
no
second attempt
engine
button quickly twice or more the
~
[~]
column.
[IT]
run
run
time change
be
programmed
01.
when the last one
be
done under such abnormal conditions. (1).The gear
(2)
Ignition key is turned
.Only under normal condition,
in
the preceding trials. If engine gets started
wHi
be made.
LCD
displays
run time I
button. Each time press
can
get
up
tirne you have gained is 15 min.
is
only accessible only when the engine is
as
required [option program table].
min
begins its countdown
of
'SP.
to
pop
up
on
to the maximum
run
time acquired. The
ON , (3)
4 start efforts will
.
the cursor and move the
this button can
Hood is opened ,(4)
the
system
run
shotoff:[-The~
].
The
'r
can
be
be
made
in
any
add
up
5 min
time of
'r
20
min. The
15.
on
the
--"
in
running.
6. I Remote engine shutoff I
(a)
, The engine
(b)
, Press and hold
flashes.
• The ,'J: .disappears frorn the remote unit's screen
the remote unit and melody is
is
running
[I];
by
remote unit.
the engine shuts off with 2 siren chirps and 2 parking light
heard.
8
.The
car's status is displayed on
)
Page 12
.J
7.
I Remote
[ intended use
(a)'
Press quickly
(b)'
Then press and release
The engine will start automatically at pre-selected temperature and begin running
and
(c)
, 'OFF" mode setting of temperature·controlled auto-start' Press and release
to turn the temperature-controlled auto·start to "OFF" mode.
The remote unit responses as (d)
, If temperature-controlled auto-start
main system sensed
(e)
, If temperature·controlled auto-start OFF
from remote's screen and the remote unit sounds
(f)'
The temp-controlled auto-start repeats maximum 6 cycles daily, with 2 hours interval
between cycles.
The temperature
accordance with your requirement.
B.
I Daily
(a)'
Press quickly[
(b)'
engine
(c) , To
the above setting
The remote unit displays different icons for different modes following the setting. (d)
, After the daily auto-start time is set to
on
(e) , After the daily auto-start time
remote unit's screen and sound
control
will automatically shut off when the pre-set run time expires.
.1'
=-1
~
to confirm this function is activated and the pre-set temperature icon like
• -lOt
~
auto-start
Press and release
will get started at the selected time daily after 24 hours from the setting.
program OFF mode of the daily auto-start
its screen and sound melody.
temperature-controlled
in
frigid countries) [ill)
2 or more times to
[IT)
appear
on
the display. The transmitter unit sounds melody.
.lOt
temperature, the engine will get started automatically).
can
be
selected for auto- start at -5Q, -10Q ,
time
ON/OFF I
ill)
2 or more times to pop up the cursor and then move it onto
[IT).
to
OFF mode.
auto-start ON/OFF
pop
up
the cursor and move it onto
.The siren chirps 3 times with 3 parking light flashes.
below:
ON
is
activated; the remote screen shows
is
activated; the icon
melody for confirmation.
Parking light flashes 6 times with 6 siren chirps .The
time'
Press and release
ON
mode, the remote unit displays •
is
set to OFF mode, the •
melody.
~
wjC=oI
-20Q
~
disappears from the
[When
~
disappears
, -30Q in
[IT)
[~b.
[IT)
the
~
[~)
to set
~~
)
9
Page 13
J
9.
I Remote
(a)
, Press quickly
(b)
, Press
Parking light flashes 3 times.
The remote unit displays status and interior temperature of the car
The temperature modes on the LCD can
as
needed.[option program table].
10. I Remote
(a)
, Regardless of the main system
release
(b) , Press and hold
light lashes.
The remote unit displays • .."..,. • on its screen along with the current status and
sounds melody.
monitor
and
release
will sound melody. For example, the •
trunk
can
temperature/status check I
[m)
2
or
more times
[II]
to monitor in-car temperature and the status of the
on
release I (The car must have electric motor for trunk release)
be
done.
[II)
for remote trunk release. Siren chirps 3 times with 3 parking
to
pop
its
screen the in-car temperature with car's security
is
at
23
degree centigrade.
be
in
lock/arm or unlock/disarm modes, remote trunk
up
the cursor and then move it onto
23t.
on
the
LCD
describes the
selected
to
show Celsius or Fahrenheit
d~b
car.
.
.
Note: The remote LCD displays •
sensor at the moment the remote trunk open
11.
mode.
(b)'
Move the cursor
The remote 'unit will response (c) • When
(d)'
When the system enters mute arm mode, the remote unit
(e)
, Even the system
(f)
, Programmable for choice of Siren or Horn [option program table)
the system enters audible arm mode, the remote unit displays •
melody sound.
sound.
remote anti-carjack
~
onto[~],then
is
mute arm mode, the siren will blurt when remote panic or is
activated
~.
when the main system bypasses the shock
is
operated by the
[
II)
press and release
as
below:
10
[II
]to
choose mute arm mode .
displays·(~
'remote
to choose audible arm
unit.
(U
••
with
.with melody
)
Page 14
J
12. I
Remote
(a) - This function can be controlled regardless of the main system
modes. ( an additional
remote unit and automatically turns off.
(b)
, Press quickly
(c) -Then press and release
on
for 30 sec before automatic turn-off.
Active
control function
channel
(ill]
2 or more times to pop up the cursor and move it on to
# 2 I (for example use of headlight auto
relay is required and can be programmed for any desired
).
For
example:
(IT].
The parking light flashes 2 times and headlight turns
to turn headlight ON for 30 sec by remote
turn-on)
in
arm or disarm
@Tl
(@]
The remote unit displays the •
(~H21
~
on
its screen and sounds melody.
* This can be programmed in accordance with function you require.[option program
table] •
13.
Ir-C=-a-r-cI'--o-c-at'--o-r,C-s-e-a-rc
(a)'
Press and release
light flashes.
The remote unit displays the car's current status on its screen and sounds melody.
14. I
Remote
(a) -
You
area
an
(b) - Press quickly (
(c) , Then press and release
shock sensor becomes ineffective but the other security functions are still effective.
The remote unit displays
Shock
can use this function
near a rail-line
* If the shock sensor is triggered for 8 consecutive times during arm mode,
system will ignore shock sensor trigger and bypass it.
I
Alarm
15. (a)
, In arm mode; if the car detects any
triggered. The siren chirps 3 times with 2 parking
mode & warn
7
h'I
both(
sensor
IT
] 2
I +
IT]
simultaneously; siren chirps 6 times with 6 parking
bypass
to
or
where trucks frequently passes
or
more times to pop up the cursor and move it onto
(IT]
.~.
away
I
avoid false alarm especially when the car
by.
to have remote shock sensor bypass during which
like
and •
I
~
impact,
~
on its screen with one beep alert.
the shock sensor's first stage alert is
light flashes.
is
parked in
door
trigger
the
Iill!l
(~]
11
Page 15
The remote unit displays r
(b)
,
If
the heavier impact
triggered .The siren blurts and the parking light flashes for 15 sec duration
o:a.
J on its screen with one long beep alert.
is
detected by the main system, the second stage alert
is
..
• The remote displays
(c)
, If the system
ignition "ON" during 30
sec and the engine start circuit
The remote unit displays icon showing triggered zone and keeps beeping for 30 sec.
• (d)
, For any triggering during arm mode, press and release
triggering. The additional of press and release
unlock/disarm mode.
enter
(e)
, The main system will enter security mode during or after the triggered zone is
closed.
still protect all other zones.
15.
(a)
, After the engine shuts
panic. The parking light
• The remote unit displays the car status
16. I Remote anti-carjack ON/OFF I
(a) (b)
,Then press and release
(c) , To
In
case of trigged zone still unlearned, the system will bypass it and can
I Remote
, Press quickly [
for 30 sec and the system's start circuit
deactivate the anti-carjack mode, press and release
panic
r~
J with beep alert for 15 sec.
is
triggered by other means like (
arm
mode) , the siren blurts and the parking light flashes
is
killed.
I
off,
press and hold both [ I +
flashes 6 times with 3 siren chirps.
on
its screen and sounds melody.
II]
2 or more times to pop
[II]
to enter anti-carjack mode. The parking light flashes
is
killed.
door-pen'
on
[I]
II]
up
the cursor and move it onto • ® J
trunk,
[I]
to make the main system
simultaneously for remote
(II]
hood-open
once to disable
again.
or
.for
The remote unit displays • @ J
on
its screen
12
and
sound alert.
Page 16
17.!Switch-controlled (a)
, While the engine
activated anti-carjack mode undergoes 2 stages
(1)
In
the
1"
stage; the parking light flashes for 30 sec.
(2)
In
the
20d
stage; 30 sec alert period during which continues blurting,
is
mode
* At any
(a) , To (b)·
To
cleared] 0
of
the alert stages, choose either
deactivate alert by switch, press and hold for 5 sec the anti-carjack switch (or)
deactivate alert by remote unit, press
anti-carjack ON/OFF]
is
running; press the anti-carjack to activate this function. The
in
the next 30 sec that follows the 1 st stage, there will
[(a)
(c)
the engine start circuit is cutoff on until active anti-carjack
as
below:
the parking light keeps flashing,
(a)
or
(b)
to
deactivate the on-going alert.
[ill]
2 or more times to pop
up
be
another
(b)
siren
the cursor
and move onto
18. ! Remote valet (a)
• Press
(b)
• Then press and release [
c)
• Press and release
(
The remote LCD displays as below : (d)
• While the valet mode is ON, the LCD remote displays
(e)
• While the Valet mode is
[ill]
4 flashes of parking light .Under the valet except for the remote door unlock and trunk release which are still operable.
restores
remote sounds melody.
all functions back to normal and become operative.
W @
~
on
the remote unit.
QN
/OFF !
2 or more times to get the cursor and move onto
IT
] to enter valet mode ON. The siren chirps 4 times with
ON mode, all functions are inoperative
[IT]
again to get valet mode OFF .The main system then
w~
OFF,
the W @
~
disappears from remote's screen but the
[~]
~
and sounds melody.
13
0
Page 17
/-)
19. I Programmable
The
TW-1
programmable functions are [valet, daily auto-start time ,temperature-controlled auto modes by means of over· ride switch
(a)
, Turn the ignition OFF
(b)
• Press and release the over-ride switch for assigned number of times to acquire desired mode settings auto-start time setting] ,
number of siren's chirps confirm the current mode setting.
(c), Turn the ignition ON when the desired mode setting
running)
(d) • To
No active
3 times to enter valet mode
4 times to enter daily auto-start time mode ON{see note setting
5 times to get mode setting
Siren
Note: If the dally auto-start time ON immediately
the
20. If page-out call button
The remote unit displays • 81. on the screen and sounds melody
choose the ON and OFF in each mode, setting, press again the over-ride switch
1 or 2
flm-es
of
presses
mode
setting
temp-controlled auto start time
and
LED
when the ignition key
en
ine in this case.)
Pa
e-out call
functions
[3
The factory default setting
on
over-ride
indicator
from
on
vehicle-base antenna case
by
over-ride
start]
in
the following procedure.
times for valet change mode setting] ,
[5
times for temperature-controlled auto-start setting]. The
follow the equal number press
Manual features program table
switch
setting·
car
VS
IS
programmed, the engine
is
turned OFF
switch
these
all
is
marked with shaded description like
I
can
be
programmed for ON/OFF
[4
times
on
the over-ride switch to
is
reached. (engine must not be
Single
.(
Use the remote LCD unit to shut off
press
ON
below}
ON
1 2
Will
is
pressed 0
Double
presses
be running
OFF OFF
OFF
for
daily
OFF.
14
Page 18
21. I Manual
Manual
(a) Turn the ignition key to (b)
Press and release the over-ride switch 8 times
(c)Turn the ignition
flash ).After
Manual
(a) Turn the ignition key to ON position. (engine must not be running) (b)
Press and release the over-ride switch 4 times
(c)
Turn the ignition key to OFF position {siren chirps 2 times with 2 flashes of park"ng light}, The system will enter Disarm mode, Note:
(a)Under manual Arm mode; if the system
(b) Under manual Arm
22.
I
Procedures
The
(1) Turn the ignition key to
Press and hold the over-ride switch for 6 sec and release it after the siren chirps 4 times which confirms the system has entered active learning mode,
(2)
Press and hold [ I +
learning
Follow the same step (2) with other remote transmitters ,one after another, to allow the main system learn coding of each transmitter.( Maximum 4 remotes can be
learned by the TW-1) ,The system will automatically jump out of learning mode if
','
..
~)
no signal
Arm
and Disarm I
Arm
Mode
ON
key
to
OFF position (siren chirps 1 time with 1 parking light
20
sec, the main system will enter Arm
Disarm Mode
alert mode ( siren chirps 3 times with 3 parking light flashes), system enters Alarm and Warn Away Mode, [The alert triggering at this stage can
be
terminated
operated by the remote unit,
for
TW-1
main system can memorize transmitter's coding ( from up
remote units)
is
completed,
is
received within 6 sec, from the last signal.
by
or
Code
"ON" (But engine must not
II]
(In
case the remote transmitter
position (engine must not
is
the car owner] 0
Disarm modes, all the system's features<:an still be
learning
simultaneously till the siren chirps 1 time ,confirming code
of
remote
be
running)
mode.
triggered, the system will enter initial
units
I
be
running)
is
lost)
20 sec
later,
to
4 different
the
* (a) The pre-memorized coding will be erased each time the learning mode is
activated, Re-do the code learning in this case,
(b) If more than one remotes are used
status will be displayed on the single remote which sends the latest
in
remote-operating the same system, the car
signal.
15
Page 19
23. I System status-indicator Fix the visibility
LED
LED
status indicator
ofit
blinking pattern with various standby modes while ignition"
LED
I
at
the appropriate location inside the car to allow maximum
Different standby modes Pattern
The remote engine being started
System System
Daily auto·start time
Ternp-controlled auto-start
Daily auto-start time auto-start Valet mode
in
disarm mode No
in
arm
mode
ON
ON
ON
+ Temp-
ON
ON
LED
solid
LED
* * * ** ** *** ***
#<***
****
*****
*****
** ** **
*
***
on
****
*
***
*****
*
****
OFF"
of
LED
*
**
***
*****
*
**
***
****
blinking
* *
**
*****
24. [Replacement
c~.
When
of
battery[
appears
on
the remote
LCD,
its battery
new battery immediately to ensure proper function.
* Replacement guide
1.
Take
off old battery
2.
Press and release
3.
. Inser] the new battery
4.
Replace the
..
battery cover and then press and release [. I ] to monitor the car's
[I]
once before inserting the new battery
[Alkaline
battery of size AAA is recommended ]
current status.
16
is
about to exhaust. Replace a
Page 20
)
25.
I Programming
The TW·1 power saving circuitry of
[Real
Operation of keys Functions
Press Press both
Press
[ill]
[I+ill] [II+ill] [II+ill) [II+ill] [II+ill]
[II+ill] [II+ill]
's
LCD
, ,
time alarm clock count-down
[ill)
[ill
& hold 3 sec Entry/exit
Press[ Press
times Press
times Press
times
times
times timinq)
ill]1
[ill]
[ill)
[m]
[ill)
Press
Press
[ill]
[ill]
Press times
Press
[ill]
Stimes power-saving
1 time Choice 2 times Choice 3 times Choice 4times
5 times Choice 6 times Choice
of
remote
remote control unit has basic features
(c)
audible or vibration alert mode
Backlight after few sec)
+ I ) Choice
mode
confirmed by 2 beeps
time Minute entry ( adjust mode)
2 Hour entry
3 Min entry
control
ON
( automatic turn-off
of
audible/vibration alert
of
adjust mode by hour, While in each
(to
adjust Alarm clock)
(to
adjust Alarm
4 ON/OFF choice for alarm clock
5 Hour entry (to adjust countdown
timing
6
Min
entry
(to
adjust countdown
7 ON/OFF choice for countdown
timing ON/OFF choice for self If the remote unit
Entry/exit
Choice of
of
alarm adjust mode
of
10 min countdown mode
of
20 min countdown mode
of
30
min countdown mode
60
min countdown mode
of
90 min countdown mode
of
120 min countdown mode
unit
timer)
I
of
(a)
EL backlight
(d)
selectable time indication
and follow the procedure
mode: Press [ I ]
"ON"
or
upwards
clock)
Press and hold [
quick adjustment upwards Press [ I )
"OFF"
or
adjust downwards
Press and
quick downwards
saving mode, its current sleeps after the system is
disarmed.
adjustment
(b)
most
as
below'
Notes
time
to choose
adjustment
II]
to choose
hold [
II]
is
entry
for
for
power
17
Loading...