Code Alarm Professional ca5054 Installation Manual

CCJCic~LA~m

~r::lOFESSIONA

I

SEr::liES

Remote Start with Keyless Entry

Installation Guide

ca5054

4280598

Table

of

Contents

Before

Wire Connection Guide ............................................................................... 4

Additional Ports ......................................................................................... 14

Set Up & Programming ............................................................................. 15

You

Begin ......................................................................................... 3

7 Pin Main Harness ................................................................................... 5

3 Pin Parking Light Harness ...................................................................... 7

6 Pin Start Harness ................................................................................... 7

4 Pin Alternate Harness ............................................................................. 9

2 Pin Door Lock Harness ........................................................................ 1 0

Antenna I LED I Programming Port ........................................................ 14

OBI

Port ................................................................................................... 14

Transmitter Programming ........................................................................ 15

Manual Feature Programming ................................................................. 15

Programming Feature Banks .................................................................. 16

Tach Programming .................................................................................. 18

Smart Tach less Mode .............................................................................. 19

Feature Descriptions ................................................................................. 19

Transmitter Button Functions .................................................................. 26

Remote Start Shutdown Diagnostics ...................................................... 27

System Layout ........................................................................................... 28

2 ca5054 Install rev

A.

BEFORE YOU BEGIN

FOR AUTOMATIC TRANSMISSION VEHICLES

PROFESSIONAL INSTALLATION

STRONGLY

RECOMMENDED

Installation Precautions:

Roll down window to avoid locking keys during

installation

Avoid mounting components or routing wires near hot surfaces

Avoid mounting components or routing wires near

in

vehicle

ONLY.

. .

moving parts

-

Tape or loom wires under hood for protection and appearance

Use grommets when routing wires through metal

surfaces

Use a Digital Multi Meter for testing and verifying circuits.

"COMPUTER SAFE PROBE"

DO NOT USE A

TEST LIGHT, OR

as these can set off air

bags or damage vehicle computers.

•

. . . .

2014

Voxx Electronics Corporation.

All

Technical

rights reserved.

Support

or

go

(800) 421-3209

to

http://avxtech1.com

3

7 Pin Main Harness

BLACK/WHITE

ILLUMINATED ENTRY

OUTPUT

- )

(

z

<{

~

z

c..

,...._

zr-

-I

a..

('I)-

(f)

C)

.....J

BROWN/BLACK RED/WHITE BLUE/BLACK PURPLE/WHITE TACH GRAY BROWN/RED

HORN OUTPUT TRUNK START

HOOD PIN INPUT BRAKE

RELEASE

STATUS

INPUT

3 Pin Parking Light Harness

BLACK

WHITE/RED

WHITE

6 Pin

Start

Harness

GROUND

PARKING LIGHT INPUT PARKING LIGHT

(-)

OUTPUT

ACTIVE

I

(-)

+ )

(

OUTPUT

- )

(

OUTPUT

- )

(

.....

a::

<(

.....

(f)

z

a:

<0

PURPLE

RED

ORANGE ACCESSORY

PINK/WHITE RED/WHITE BATTERY 12V ( PINK

STARTER BATTERY 12V (

IGNITION

4 Pin Alternate Harness

BLACK/YELLOW PULSE DURING GREEN/WHITE PULSE LT BLUE L T GREEN/BLACK

FACTORY FACTORY DISARM

2 Pin Lock Harness

OUTPUT-

( + )

2

( + )

1

AFTER

ARM

MOTOR SIDE

+)

( + )

1

+)

CRANK (

SHUTDOWN

PULSE AFTER START

I

- )

PULSE

- )

(

BEFORE START

(-)

- )

(

z:::S:::

-(.)

a

a..

N.....J

4

BLUE GREEN

UNLOCK LOCK

(-)

ca5054 Install rev A.

7

Main

H.arness

1

This wire provides a ( - ) 200mA output for 30 seconds when the system

capable Locate the vehicle's dome light or pin switch wire.

2

Locate the vehicle's horn wire.

Connect the BROWN/BLACK wire to the vehicle's horn wire. This is a low current

output, 200mA.

BLACK/WHITE ILLUMINATED ENTRY OUTPUT

of

driving relays.

Verification: This wire will register positive voltage or ground when the

vehicle's dome light

BROWN/BLACK HORN OUTPUT ( - )

Verification: This wire will register at positive voltage and register

ground when the horn switch is pressed.

is

turned ON.

(-)

is

disarmed

3 RED/WHITE TRUNK RELEASE OUTPUT ( - )

Locate the vehicle's trunk release wire at the trunk release switch.

Verification: This wire will register either positive voltage or ground when

the trunk release is activated.

This is a low current output, 200mA and is configurable

in

option programming

4 BLUE/BLACK START STATUS I ACTIVE OUTPUT ( - )

This wire provides a ( - ) 200mA output when the remote start function is activated

and remains used for multiple application's a 1 amp diode is required in-line with the stripe facing

the control module.

until4

seconds after the remote start is shutdown. If this wire will be

5

PURPLE/WHITE

TACH INPUT

Locate the

1.

Set voltmeter

2.

Attach positive

3.

Attach negative lead

4.

Start

5.

Have someone press on the gas connected to the correct wire, the

vehicle's ignition

Verification:

to

the engine.

coil

or

Test using the

AC VOLTS.

lead

of

a

volt meter to a constant

of

a volt meter to the wire to be tested.

fuel

injector

following

procedure:

pedal slightly

voltage reading

in

the engine compartment.

12-volt

as you monitor the meter.

RPM increases.

Connect the PURPLE/WHITE wire to the negative side

fuel injector.

6 GRAY

Install

a Hood Pin Switch and connect to the GRAY wire. This connection is required

HOOD PIN INPUT

for Remote Start.

source.

If

will increase as the engine's

of

the vehicle

ignition

coil

or

(-)

Verification:

This wire when connected will

vehicle's hood is opened.

Connect the GRAY wire to the hood pin.

NOTE:

7

Locate the

Be sure to

loom the wire, and

BROWN/RED

vehicle's brake

seal

the grommet.

BRAKE

INPUT(+)

light wire at the brake

connection is required for Remote Start.

Verification:

This wire registers positive

voltage

pressed.

Connect the BROWN/RED wire to the vehicle's

register ground when the

pedal

brake

mounted switch. This

when the brake

light

wire .

pedal is

6

ca5054 Install

rev

A.

3 Pin Parking Light Harness

1

Connect the BLACK wire to a self

BLACK

tapping screw (not

solid chassis ground point using a ring terminal and

supplied).

GROUND

Scrape away paint from the grounding point to

ensure a good connection. The recommended grounding point is a

the driver's side kick panel area.

NOTE:

2

3

Locate the parking

Do not ground the BLACK wire with any other

vehicle

WHITE/RED PARKING LIGHT INPUT

WHITE

Verification:

light

output wire at the

This wire registers positive

PARKING LIGHT OUTPUT

vehicle's light

voltage

switch.

when the parking

components.

turned on.

Positive switching Parking Lights:

metal

lights

surface

are

in

Connect the Connect the

WHITE/RED wire to a 15 Amp max fused battery source. WHITE

wire to the parking light output wire.

Negative switching Parking Lights:

Connect the WHITE/RED wire to a good chassis ground. Connect the

6 Pin Start

1

Locate the

PURPLE

Verification:

vehicle starter wire.

WHITE

wire to the parking

Harness

This wire registers voltage

START position.

Connect the PURPLE wire to the

STARTER OUTPUT

vehicle

light

only

starter wire.

output wire.

(

+ )

when the key is turned to the

2014

Voxx

Electronics

Corporation.

All

rights reserved.

7

2

RED

BATTERY

12V

(

+)

Locate 1

of

Verification:

switch.

Connect

NOTE:

3

the RED wire to the constant 12 Volt

Remove

ORANGE

Locate the

Verification:

(Accessory) and key is turned to the START (or

Connect

4

the

PINK/WHITE

the vehicle's

This wire

fuses

all

vehicle's

accessory

This wire registers

ORANGE

constant 12 Volt

register ( + ) voltage

will

battery wires at the ignition switch.

all

in

battery wire.

until all

the

ON

connections are made.

ACCESSORY

the ignition switch.

at

wire

when

position.

The

(or

voltage

RUN)

CRANK)

1 ( + )

the key is turned to

voltage

wire to the vehicle's accessory wire.

+ )

(

IGNITION

2

positions

drops

the ignition

of

ACC

when

out

the

Locate the

Verification:

vehicle's

2nd ignition wire

This wire registers RUN) position, but not the drop

Connect

when

out

PINK/WHITE

the

the key is turned to the START (or

Programmable output:

5

Locate 1

RED/WHITE

the vehicle's

of

Verification:

This wire

switch.

RED/WHITE

Connect

NOTE:

the

Remove

all

fuses

ACC

wire to

IGN,

the

ACC, Start.

constant 12

register ( + )

will

wire to

until all

the

connections are made.

the ignition switch (if equipped).

at voltage

when

(Accessory) position.

vehicle's

BATTERY

battery wires at the ignition switch.

Volt

voltage in all

the key is turned to the

voltage

The

CRANK)

ignition 2 wire.

+)

(

12V

positions

position.

constant 12 Volt battery wire.

ON

does

the ignition

of

(or

not

8

ca5054 Install

rev

A.

6

PINK IGNITION 1 (

+)

Locate the vehicle's ignition wire at the ignition switch.

Verification: This wire registers voltage when the key is turned to the ON (or

RUN) position. The voltage does not drop out when the key is turned to the

START (or CRANK) position. Connect the PINK wire to the vehicle's Ignition wire. This wire is also used for Ignition 1 Output.

4 Pin Alternate Harness

1

BLACK/YELLOW PULSE DURING

CRANK

(-)

Locate the vehicle's second starter (crank) wire at the ignition switch. (if equipped)

Verification: This wire registers voltage only

in

the start (crank) position

of

the ignition switch.

This wire will supply a

(-)

200mA

output and can be configured

in

option

programming.

2 GREEN/WHITE PULSE

This wire will supply a ( - )

200mA

pulse after the remote start shuts down. This

is typically used to re-lock the vehicle's doors

AFTER

if

they unlock upon remote start

SHUTDOWN ( - )

shutdown. It can also be used to pulse a door pin-switch wire to prevent the vehicle's accessories from remaining on after remote start shutdown.

This output is configurable

in

option programming.

LT

3

BLUE FACTORY ARM I

This wire will supply a ( - ) successful completion

of

re-lock the vehicle's doors upon remote start

This output is configurable

200mA

PULSE

pulse both upon arming the system and upon

AFTER

START ( - )

the remote start activation sequence and is typically used to

if

necessary.

in

option programming.

9

4

LT

GREEN/BLACK

FACTORY DISARM

I

This wire

will supply

PULSE BEFORE START

a

( - ) 200mA pulse both upon disarming the system and when

(

the remote start feature is activated. Locate the factory perimeter from the key cylinder

inside the drivers door.

Verification: This wire registers ground if the key is turned to the

position in the driver's door

This output

is

conffgurable

in

cylinder.

option programming.

2 Pin Door Lock Harness

1

2

BLUE

GREEN

UNLOCK

LOCK

(-)

- )

alarm

disarm wire

unlock

The door

lock

I

unlock outputs are designed to control several different types systems which may require chart to see which type types are shown

in

These wires supply a

the

following

(-)

of

door

500mA

additional

lock system is

diagrams.

output.

parts. Please

in

your

review the wire and

vehicle.

The most common

of

location

10

ca5054 Install rev

A.

Negative Switching Locks

All Door Lock and Unlock: Locate the lock I unlock wire at the vehicle's lock I unlock

switch.

Verification: These wires will register ground when the Lock and Unlock

switches are activated.

in

Connect the GREEN and BLUE wires shown

the diagram below.

Negative Locks:

GREEN ( - ) Lock Output

Vehicle Door Lock

Control Relays

BLUE ( - ) Unlock Output

Positive Switching Locks

All Door Lock and Unlock: Locate the lock I unlock wire at the vehicle's lock I unlock

switch.

Verification: These wires will register positive voltage when the Lock and

Unlock switches are activated.

in

Connect the GREEN and BLUE wires shown

the diagram below.

Positive Locks:

GREEN ( - ) Lock Output

Vehicle Door Lock

Control Relays

11

Reverse

All

Door Lock and Unlock: Locate the lock

Polarity

Locks

(5-Wire

Door

switch.

locks)

I

unlock wire at the vehicle's lock

I

unlock

Verification: These wires

will rest at ground and register positive

voltage when the Lock and Unlock switches are activated.

Connect the GREEN and BLUE or BLUE/GREEN wires shown using (2)

SPOT

relays (not supplied).

Reverse Polarity Locks:

GREEN (

-

) Lock Output

BLUE (

-

)

Unlock

Output

...._

___

Cut

~

To Door Lock Motor

in

the diagram below

Negative Multiplexed

All

Door Lock and Unlock: Locate

Locks

the lock

I

unlock wire at the vehicle's lock

switch.

Verification: This wire

will show variable ground when the switch is activated. Please consult the wire and location chart for specific resistor values for your vehicle.

Connect the GREEN and BLUE or BLUE/GREEN wires shown using (2)

SPOT

Multiplex

relays (not supplied).

Locks:

I

unlock

in

the diagram below

BLUE (

-

)

Unlock Output

12

Vehicle

Door Lock

Control Relays

ca5054 Install

rev

A.

Positive

All

Door Lock and

Multiplexed

switch.

Locks

Unlock:

Locate the

lock

I

unlock

wire at the

vehicle's lock

I

unlock

Verification:

activated. values

This wire

will

show variable positive voltage

Please consult the wire and location

for your vehicle.

chart for specific resistor

Connect the GREEN and BLUE or BLUE/GREEN wires shown using (2) SPOT

Multiplex

relays

Locks:

(not supplied).

Vehicle

Control Relays

when the switch

in

the diagram

BLUE ( - ) Unlock

Door Lock

Output

is

below

Adding Aftermarket Actuators

After wires shown

installing

in

aftermarket actuators, (not supplied). Connect the GREEN and BLUE

the diagram below

-----f------f

___

87

using (2) SPOT relays

.,__-I

Fused +12 Battery Source

Fused +12 Volt Battery Source

Volt

(not

supplied).

BLUE ( - ) Unlock

Output

13

Additional Ports

Antenna

Mount the will

not

I

LED

supplied

block

I

Programming Port

antenna/receiver to a

the driver's vision. A good near the rear view mirror. Be careful not metallic cable to the

Data Bus Interface Port

This 4 pin port to communicate with the

Flashlogic

be on

window

film,

as this will

control module

is

used for

Flashlogic

vehicle's

Door Lock and Transponder

available. Please

refer to the

the tech service web site.

effect system range. Route the antenna/receiver

and

plug

into the antenna port.

Door Lock and Transponder Databus

Databus. When using the

020

(Data to Data) function

clear

location

spot on the

is

usually high on the windshield

vehicle's windshield

to mount the antenna/receiver on any

DBI

Interface modules

port to

the

following options may

list available

control

per

that

Interfaces

the

vehicle

Tach Trunk/Hatch

Door Lock

Input Brake

Open Diesel Glow Plug Input

Control Passlock

Safety Shut Down

I

Passkey Interface (GM

Dome Light Supervision Transponder

Factory

Alarm

Arm

I

Disarm Manual

Arm

controls system)

Interface

I

Disarm

Only)

Activation

Inputs (factory keyless

14

ca5054 Install

rev A.

Set Up & Programming

Transmitter Programming - Feature Bank 1

1.

2.

3.

4.

5.

6.

Turn the ignition ON.

Press and hold the valet/override button.

Within 10 seconds the system will chirp (3) three times.

Press 1 button of each transmitter you wish to program.

The system will respond with 1 chirp for each accepted transmitter.

Pressing the override button at anytime during programming will advance to

the next bank.

NOTE: The system will exit transmitter programming after 15 seconds

NOTE: This system has 1 button programming which programs all channels of the

of

inactivity.

system.

NOTE: The system will hold up to 4 transmitters

transmitter will erase the oldest transmitter

NOTE: This system has PTN - Programmed Transmitter Notification. Each time the

ignition

is

turned ON, the LED will flash the number of transmitters programmed to the

in

memory, programming a 5th

memory.

system.

Manual Feature Programming - Feature Bank 2 - 5

1.

2.

3.

4.

5.

6.

Defaulting All Features: Pressing the

banks will default all features and return you to feature bank 2 - 4 chirps.

Turn the ignition ON. Press and hold the valet/override button. Within 10 seconds the system will chirp (3) three times. Use the valet/override button to advance through each option bank. For

feature programming advance to Feature Bank

2,

3,

4,

or 5 which

four, (5) five, (6) six and (7) seven chirps. Use the transmitter 0 button to scroll through the selections

in

each feature

bank, the system will chirp to match the feature number. Press the transmitter

(]:)

button to change the desired feature. The LED will

flash indicating the changed feature.

ciJ

button anytime while

in

any

of

is

(4)

the feature

NOTE: The system will remain

is

on, there

is

no time limit.

in

feature programming mode as long as the ignition

To

exit programming turn the IGNITION

OFF.

15

Feature Transmitter

Bank

1 -

Programming

3

Chirps

Refer to transmitter programming.

Factory Disarm

Lt

Green

I

On

Black

this

model

the

Lt

Green

2

NOTE:

16

Factory

Disarm

I

Black

Bank

Output

5

will

2nd

Unlock

wire

override

can

Factory Disarm Factory Disarm Factory Disarm

Start

be

configured

changes

Status

made

350mS 500mS

in

Bank

3

or

Bank

in

Bank

3.

5.

Any

changes

ca5054

to

this

feature

Install

rev

in

A.

2014 Voxx Electronics Corporation.

All

rights reserved.

17

Feature

4 Pin Alternate

4 Black I Yellow Output

Bank

5 - 7

Output

Chirps

Control

Pulse

During

Crank Running

Ground While

T

1

gm 10n

NOTE: On

this

model

the

Lt

Green I

Black

Output

will

wire

can

override

be

configured

changes

made

in

Bank 3 or

In

Bank

3.

Bank

5.

Any

changes

to

this

feature

in

Tach Programming

The unit will not operate unless a tach signal is programmed option is turned ON.

If

an

attempt

is

made to start the vehicle via the remote start without first programming tach, the unit will flash the parking lights 7 times indicating tach has not been learned and stored. If the tach rate is not properly programmed to the specific vehicle, the unit may not realize that the vehicle

instances and reengage the starter motor.

The Remote Start unit will learn the tach rate

packs, or single injector.

1.

2.

3.

Turn the ignition key to the ON position. Press and release the valeUoverride button 3 times. Immediately turn the ignition key

To

learn tach:

of

most vehicle's single coil, multiple coil

OFF.

or

is

running

the tach less

in

certain

Bank

5

4.

5.

Press and hold the valeUoverride button, then start the vehicle using the

key.

When the unit senses the tach signal, the parking lights will begin to flash.

6.

7.

Allow the vehicle to settle to a normal idle speed. Release the valeUprogram push-button switch. 1 long chirp and the

parking lights will turn on for 2 seconds indicating that the learned tach signal is stored and the unit has exited tach learn mode.

NOTE: If the unit fails to learn tach rate due to

poor tach source, the parking lights will not flash. connect the PURPLE/WHITE wire to the proper tach signal, and then repeat the tach

learn routine.

18

an

improper tach connection or a

To

correct this situation, locate and

ca5054 Install rev

A.

Smart

Tach

less Mode

Smart system and when activated programming to Tachless without the need to enter the feature programming mode.

Feature

1

Tach

1.

2.

3.

Feature

-Silent

less

Mode is available

will automatically

Activate the remote start. The parking

times indicating no tach Within the 7 The system

mode.

flash

will

chirp 1 time indicating the system is now

only

if a tach signal

signal

time period, press and

has been learned.

Descriptions

Bank

Choice:

2-

Security

Controls the normal arm/disarm chirps

has never been learned to the

change the Tach Mode feature

lights

should begin flashing 7

hold

the

0

button.

in

tachless

of

the security system.

in

option

ON

-

Silent arming/disarming upon first press

unlock a second time system will only lock/unlock

OFF -

2 - 8

Not

9 -

OBI

interface with external modules.

OBI

ADS

10 - Not

11

-

L.E.D.

normal

available

Port

Protocol:

Protocol

available

Output

sound the arm/disarm chirps upon a second press

buttons.

arm/disarm chirps upon the first press

on

this

when Armed:

will

this

model.

Determines the protocol type

model.

locked.

of

lock/unlock, pressing lock/

activate the arm/disarm chirps respectively. The

of

the

of

lock/unlock.

in

Control

which the

of

the LED when the

OBI

port uses to

system

is

armed

I

ON

- LED

OFFnormal operation (armed/locked) and does not affect programming, mode, diagnostics, passive

2014

Voxx Electronics Corporation.

will

LED

flash when system is armed

will not

All

flash

rights reserved.

when system

lock

I

locked

is

armed

countdown or PTN.

I

locked. Only

applies to

valet

19

Feature Bank 3 - Output Control

1 -Extended Lock Pulse: Controls the timing

of

the BLUE and

GREEN

wires.

1 Second - Single 1 second lock pulse, single 1 second unlock pulse.

3.5 Seconds - Single 3.5 second lock pulse, single 3.5 second unlock pulse. 1 Second Lock, Double Pulse

Unlock-

Single 1 second lock pulse, double 1

second unlock pulse. 30 Second Lock, Double Pulse Unlock - Single 30 second lock pulse, double

1 second unlock pulse. Double Pulse Lock, 1 Second

Unlock-

Double 1 second lock pulse, single 1

second unlock pulse.

2 - Factory Disarm - Lt Green/Black Output: Controls the timing

BLACK

factory disarm output.

Factory Disarm - Single 1 second pulse with unlock and remote start activation.

2nd Unlock -

Same

output as unlock with 2nd press

of

unlock.

of

lock output

the

LT.

GREEN/

Start Status - Single

1 second pulse with unlock and continuous output

during the remote start cycle. Factory Disarm - Single 350mS second pulse with unlock and remote start

activation. Factory Disarm - Single 500mS second pulse with unlock and remote start

activation.

NOTE: On this model the Lt Green I Black Output wire can be configured in Bank 3

or

Bank

3.

3 - Ignition Controlled Locks: Control

or

OFF.

5.

Any

changes to this feature in Bank 5 will override changes made in Bank

OFF

- Door locks not activated by ignition.

Lock and

Unlock-

Doors lock when ignition is turned on and unlock when

ignition is turned off.

of

door

locks when the ignition is cycled ON

Lock Only - Doors lock when ignition is turned on only. Unlock Only Doors unlock when ignition is turned

20

off

only.

ca5054 Install rev

A.

4 - Trunk

Output

Timing - Red/White

RED/WHITE output.

1

Second Pulse -

1

0 Second - Continuous output for 1

1 second

pulse

Output: Controls

output.

0

seconds.

the output timing/type of the

5 -

Horn

some

6 -

Real

20 Seconds Latched

- Continuous output for

until IGN

ON

- Continuous output

ON. Latched

is

pressed again.

Output

vehicle will 16mS

Panic:

ON OFF-

ON

until

Button Press - Continuous output

Timing:

require a

1

OmS

Controls

Control

longer

the minimum horn

pulse

30mS 40mS 50mS

the panic out when triggered from the transmitter.

- Randomized horn honks when panic Standard pattern horn honks when panic

20

seconds.

until

the vehicle's

until the activation button

pulse time

in

milli

to activate the factory horn.

is

triggered.

is

triggered.

ignition

seconds,

is

turned

Feature Bank 4 - Remote Start Control

1 -

RF

Start Chirp: Turns remote start activation confirmation chirps

2 - Run Time:

control

of

down at any time by use of the transmitter or system shutdowns.

3 - Running Lights: start.

Steady-

Flashing

Controls

the time

the remote start

Controls the WHITE

Parking

lights

- Parking

in

minutes that the

until

the system times out. The system may

vehicle will stay running under

parking light output wire during remote

constant during the remote start

lights flash

at a

slow

pace during the remote start

cycle.

ON

also

or

OFF.

be shut

cycle.

21

4 - Tach Mode: Determines how the system monitors the engine running during

remote start.

Tach - Hard wired directly to the tach wire

of

the vehicle to monitor AC

voltage. Tach less (Crank Average/Voltage) - Determines crank time by averaging the

last 8 times the vehicle was started with the key and then monitors the

change

Hybrid (Crank Average

the last 8 times the vehicle was started with the

OBI

connected to the

in

voltage after remote start.

I No Voltage)- Determines crank time by averaging

key.

Port - Monitors the vehicle's tach rate through

OBI

port.

an

interface module

5 -Voltage Level: The voltage variance for remote start when set to tachless. (see

tach mode)

HIGH - The variance is

activated to after the engine is running must be greater than 0.5 volts.

LOW - The variance

in

battery voltage from before the remote start

in

battery voltage from before the remote start

is activated to after the engine is running may be less than 0.5 volts.

6

-Crank

Time: Preset output times for the PURPLE starter wire.

1 Second 0.8 Seconds 1.5 Seconds 2 Seconds 4 Seconds

7 - Crank Average I Crank Time: The length

of

time

in

which the remote start will

crank the vehicle's starter.

Crank Average - Determines crank time by averaging the last 8 times the vehicle was started with the

Preset

8-

Gas I Diesel: Selects engine type and delay time for the starter output wire

Time-

Preset starter output time. (see crank time)

key.

during remote start activation.

Gas-

Gasoline engine, no delay for the starter output wire.

10 Second Delay - Diesel engine, delays the starter output wire for 1 0

seconds after the ignition has been powered up by the remote start.

15 Second

Delay-

Diesel engine, delays the starter output wire for 15

seconds after the ignition has been powered up by the remote start.

20 Second Delay - Diesel engine, delays the starter output wire for 20

seconds after the ignition has been powered up by the remote start.

45 Second

Delay-

seconds after the ignition has been powered up by the remote start.

22

Diesel engine, delays the starter output wire for 45

ca5054 Install rev

A.

9 -

Single

single or

10

-

IGN

I

Double Pulse Start:

double

2

Output:

press from the transmitter.

Programmable

Switches the remote start activation between a

high current output.

Ignition 2

-

Ignition

output during remote start. Accessory- Accessory output during remote start. Start

11

- 2 or 3 Hour

I

Crank -

Crank

Start:

output during remote start.

When activated, the remote start

programmed time and shut down every 2 or 3 hours.

12 - 14 Not available

15 -Accessory

Output:

on

this

model.

Programmable

high current output.

Accessory - Output becomes active with the same timing as the accessory output, drops out during crank.

Ignition

- Output becomes active with the same timing as the ignition output

and does not drop out during crank. Start

output wire, during crank

I

Crank

- Output becomes active with the same timing as the starter only.

will

activate and run for the

2014

Voxx

Electronics Corporation.

All

rights reserved.

23

16 - Pulse Additional Outputs

w/

Unlock: When the Unlock button is pressed on

the remote transmitter the system will also simultaneously pulse additional outputs. Ignition, Accessory & Ground While Running outputs for 1 second. The 3rd setting also activates the pulse after shutdown output to turn off the RAP on certain vehicles

OFFIGN, ACCY,

simultaneously pulse the Ignition, Accessory

When Unlock is pressed no additional outputs are activated.

GWR-

When the Unlock button is pressed the system will also

& Ground while Running outputs

for 1 second. IGN, ACCY, GWR, then Pulse After

Shutdown-

When the Unlock button is pressed the system will also simultaneously pulse the Ignition, Accessory & Ground while Running outputs for 1 second then waits 2 seconds then pulses the green/white pulse after shutdown wire for 1 second.

17 - Door Lock Control During Remote Start: Controls the systems door lock

outputs during the remote start sequence.

or

OFF - The system will not lock Unlock before Start, Lock After

unlock the vehicle.

Start-

Unlock Pulse before remote start sequence begins, Lock pulse after remote start sequence is complete and engine is running.

Unlock Before

Start-

Unlock Pulse before remote start sequence begins.

Lock After Start - Lock pulse after remote start sequence is complete and engine is running.

Lock After Shutdown - Lock pulse after remote start shutdown sequence is complete.

Feature Bank 5 - 4 Pin Alternate Output Control

1 - Lt Green/Black Output : Controls the L T GREEN/BLACK output activation type

and timing.

Pulse before Start

I During

activated. Also a 1 second pulse when unlock is pressed. Ground While Running - Continuous output for the entire remote start

sequence until after the vehicle shuts down. Ignition - Output becomes active with the same timing as the ignition output

and does not drop out during crank. Accessory-

Output becomes active with the same timing as the accessory

output, drops out during crank.

Unlock-

1 second pulse when remote start is

Pulse During Crank - Output becomes active with the same timing as the starter output wire, during crank only.

24

ca5054 Install rev

A.

2 -

Lt

Blue

Output :

Controls

the

LT

BLUE output activation type and timing.

Pulse

After

Start

I

During Lock - 1 second sequence and has confirmed the when

lock

is pressed.

Ground

While

sequence Ignition-

Running - Continuous output for the entire remote start

until

after the

vehicle

Output becomes active with the same timing as the ignition output

and does not drop out during crank.

Accessory - Output becomes active with the same timing as the accessory

output, drops out during crank. Pulse During Crank - Output becomes active with the same timing as the

starter output wire, during crank

3-

Green/White

Output:

Controls

timing.

Pulse

After Shutdown - 2 second

shutdown.

Ground sequence

While

until

Running - Continuous output for the entire remote start

after the

vehicle

shuts down.

only.

the

GREEN/WHITE output activation type and

pulse

shuts down.

pulse

is running.

after the remote start

Also

a

1 second

after the remote start has

pulse

Ignition

and does not drop out during crank. Accessory

output, drops out during crank.

Pulse

starter output wire, during crank

4 -

Black/Yellow

timing.

Pulse starter output wire, during crank

Ground sequence

Ignition and does not drop out during crank.

Accessory - Output becomes active with the same timing as the accessory output, drops out during crank.

- Output becomes active with the same timing as the ignition output

- Output becomes active with the same timing as the accessory

During Crank - Output

becomes active with the same timing as the

only.

Output :

Controls

the

BLACKNELLOW

output activation type and

During Crank - Output becomes active with the same timing as the

only.

While

Running - Continuous output for the entire remote start

until

after the

vehicle

shuts down.

- Output becomes active with the same timing as the ignition output

2014 Voxx

Electronics

Corporation.

All

rights reserved.

25

Transmitter Button Functions

26

ca5054 Install

rev

A.

Remote Start Shutdown Diagnostics

If the remote start shuts down or fails to start, the parking lights will flash one of the

patterns below indicating the shutdown input. To

manually enter diagnostics and view the last shutdown, turn the ignition

press and release the

LED

FLASHES

._.

button.

SHUTDOWN ZONE

ON

and

3 Flashes

4 Flashes

5 Flashes

7 Flashes

Hood Brake

Remote

Input

Start Valet Mode

Manual Transmission Mode not set (manual

transmission models only)

Tach not learned

I

Crank Average not learned

2014 Voxx Electronics Corporation.

All

rights reserved.

27

"'

(X)

#

4120106

#

4120102

#4120103

D

E~

......

N

L()

n:LO

0

<D

s(j

(")

'<t

ll:

#

4120107

~

IU

0 0

u

#

4120192

#

4120110

BLUE GREEN

BLACK/YELLOW GREEN/WHITE LT

BLUE

L T

GREEN/BLACK

BLACK WHITE/RED WHITE

BLACK/WHITE BROWN/BLACK RED/WHITE BLUE/BLACK PURPLE/WHITE GRAY BROWN/RED

OBI PORT

ANTENNA LED

0

VALET

#

4180025

PURPLE RED ORANGE PINK/WHITE RED/WHITE PINK

UNLOCK

(-)

LOCK

(-)

PULSE DURING

CRANK

( - )

PULSE

AFTER SHUTDOWN ( - )

FACTORY

ARM

I

PULSE

AFTER

START ( - )

FACTORY DISARM

I

PULSE

BEFORE

START ( - )

GROUND PARKING LIGHT INPUT PARKING LIGHT

OUTPUT

ILLUMINATED ENTRY

OUTPUT

( - )

HORN OUTPUT

(

- )

TRUNK RELEASE

OUTPUT

( - )

START STATUS

I

ACTIVE

OUTPUT

(-) TACH INPUT HOOD INPUT

(

- )

BRAKE

INPUT

(

+)

STARTER

OUTPUT-

MOTOR SIDE

(

+)

BATTERY

12V (

+)

ACCESSORY 1 (

+ )

IGNITION

2

( + )

BATIERY

12V (

+)

IGNITION

1

(

+ )

2014 Voxx

Electronics

Corporation.

All

rights reserved.

29

30

ca5054 Install

rev A.

Electronics Corporation. All

Voxx

2014

rights reserved.

31

FCC

COMPLIANCE

Voxx

Electronics

Corporation.

Customer Service 1-800-421-3209

WWW.CODE-ALARM.COM

This device complies with Part 15 of the Industry

1.

This device may not cause harmful interference, and

2.

This device must accept any interference received,

Canada. Operation is subject to the following two conditions:

may cause undesired operation.

Warning!

Changes or modifications not compliance could

32

void the user's authority to operate the equipment.

expressly

R41

0-192-690

FCC rules

and with

RSS-21 0

including

approved by the party

of

any interference that

responsible

for

ca5054

Install

rev

A.

CCICc:~~~m

Remote

IMPORTANT NOTE:

applicable

SAFETY PRECAUTIONS

Electronics

Voxx

2014

Corporation .

The operation

to most vehicles.

All

Start

and

Entry System

the Security and Convenience

of

However, due to the configuration

may not

rights reserved.

apply. Please

see your

Keyless

System

some vehicles,

of

installing dealer

as described in this manual

some functions

for more information.

AND/OR

4280599

is

Table

of

Contents

Using Your Remote Control

Using the

Two

Stage

Activating Trunk Release (optional) ................................................... 3

Using the Progressive Car Finder Feature ........................................ 3

Using the

Programmed Transmitter Notification ................................................ 3

Valet Eliminating

Using Your Remote

Remote Starting Your Remote Entering Your Preheating or User Programmable Using the "Quick-Stop"

Operating the 2 Operating the Remote

Keyless

Door

Personal Protection

Mode ........................................................................................ 4

Lock

Entry .................................................................... 3

Unlock (optional) ..................................................... 3

I

Unlock

Vehicle

Start

Start Safety

Shutdown .................................................................... 4

Vehicle while Precooling

I

3 Hour Start

Daily Start

.................................................................... 3

Alarm ................................................. 3

Notification Chirps .................................... 4

Starter ....................................................... 4

Vehicle

Run Time

Feature ......................................................... 5

Features ........................................................... 6

............................................................ 4

it

is

Running via Remote Start .............. 4

the

Vehicle's Interior ................................. 5

I

Run Time Extension ....................... 5

Up Timer Mode .................................. 5

Timer ......................................................... 6

Transmitter Button Functions ................................................................ 7

Replacing Warranty

2

Remote

Control

Information

.............................................................................. 8

Batteries ..................................................... 7

ca5054 Owners

rev A

Using Your Remote Control

Using the Keyless Entry

used to unlock the

button

&J

The vehicle's doors.

used to lock

is

lock or unlock the doors simply press and release the desired

To

the vehicle's doors, the

~

function button one time. For your convenience, the parking lights

the doors are unlocked and twice when the door are locked.

defaulted with Silent Choice enabled, which requires a second

NOTE: The system

@

the

press

the vehicle. If

of

your system

is

or button to activate

set up for 2 step unlock, a third press of unlock

is

audible locking/unlocking response from

an

activate the audible response.

Stage Door Unlock (Optional)

Two

button one time

this feature

If

enabled

is

your system, pressing the

on

,?

only the driver's door. Press again within three seconds to unlock the remaining doors.

is

will flash

once when

will

unlock

will

Activating the Trunk Release Feature (Optional)

open the

The button is used to open the trunk of the vehicle.

the button for 3 seconds.

press and

hold

To

Using the Progressive Car Finder Feature

button to locate your vehicle. The system

)))

Press the

c::J

and sound 5 times at

volume, increasing

low

volume each time the button

in

will flash

pressed.

Using the Personal Protection Alarm (Panic)

button for 3 seconds to activate the personal protection alarm.

)))

Press and

hold the

c::J

During panic mode, the normal function of the transmitter buttons

and unlock the door (if the

and buttons can be used to

The transmitter's

installed).

option

is

@

stop the alarm, press and hold the

To

again for 3 seconds. The system

will automatically

lock

)))

c::J

stop after

button

30

vehicle's trunk

the parking lights

is

suspended.

be

will

the transmitter

on

seconds.

Programmed Transmitter Notification

As a security precaution each time the vehicle's ignition is turn light with

flash

the number of transmitters programmed into the system. This to identify unauthorized transmitters from accessing your unauthorized transmitter has been programmed to your system, contact your dealer for assistance.

2014 Voxx Electronics

Corporation.

All

rights reserved.

the status LED

on

helps

vehicle. If you believe

installing

an

3

Valet Mode

Valet

enter or exit

Eliminating Lock I

System

Mode

valet

1.

2.

3.

4.

lock and

is

used to

mode Turn the Push and The LED

disable

the system from remote starting.

simply follow vehicle's

hold

will

ignition

the programming/valet button.

turn on

the 4 steps outlined below:

ON.

solid when valet

Release the programming/valet button.

Unlock Notification Chirps

unlock

notification chirps can

entering the programming feature banks.

1.

2.

Turn the ignition Press and

will

respond with 1 chirp for

release

ON

the valet/programming button 3 times. The system

then

OFF.

ON

or 2 chirps for

Using Your Remote Vehicle Starter

mode is active

be

toggled

ON

OFF.

To

or

OFF without

Remote Starting Your Vehicle

To

activate the remote vehicle

within 2 seconds. The system

system will correct,

check the vehicle

the vehicle will start within 5 seconds. The

(or flash depending on system settings) as a

started and

If

your

2 more times to start the

is

running.

vehicle stalls

or does not start, the system will

vehicle 5 seconds between each start attempt. attempt, the system

will abort the remote vehicle

start function, press and

will

sound, the parking lights will flash

to ensure it is safe to start.

vehicle's

visual

indication that the

pause 5 seconds, then try

(a

total

of 3 attempts). The system

If the

vehicle

does not start after the 3rd

start process.

release

If all

parking

the button 2 times

safety parameters are

Remote Start Shutdown

Press and

hold

the button for 3 seconds to turn the vehicle

off.

Entering the Vehicle while it is Running via Remote Vehicle Start

1.

Unlock

the vehicle's doors.

1 time and the

lights will

vehicle

will

pause

turn on

has

2.

3.

Enter the

Insert

the key into the ignition switch and turn to the

vehicle. DO NOT PRESS

position.

4.

4

Press the brake pedal.

the

vehicle will

operate

The remote

normally.

THE BRAKE PEDAL!

ON

vehicle starter

will

disengage and

or RUN

ca5054 Owners rev A

Preheating

or

Precooling the Vehicle's interior

Before exiting the vehicle, set the temperature controls to the desired setting and operation. After the system starts the vehicle, the heater or air conditioner will activate and heat or cool the vehicle's interior to your setting.

User Programmable Run Time I Run Time Extension

The system has the ability to allow the user to extend the time the vehicle will be running under control of the remote start. This will only extend the run time back to the

is

current run time setting during the current remote start cycle. If your system

is

run 15 minutes and the time remaining

4 minutes, extending the run time will reset

set to

the countdown timer to 15 minutes and your vehicle will continue to run for another 15 minutes. Follow the steps below to extend the vehicle's run time.

1.

2.

3.

The remote start must already be active. Press and release the button 4 times. The system will chirp 1 time and flash the parking lights 4 times to

confirm that the run time has been reset.

Using the

~~Quick-stop"

Feature

If you want to make a short stop and keep your vehicle running (to keep the interior warm or cool), the quick-stop feature allows you to do this while keeping your vehicle secure and your keys with you.

To

engage quick stop:

1.

2.

Stop the vehicle and place the transmission

in

PARK.

With your foot off the brake pedal, press and release the

-~

button 2

times within 2 seconds. The LED will flash 3 times to confirm quick

is

entered.

r]J

3.

stop Remove the keys from the ignition and exit the vehicle. Press the

button to lock the vehicle's doors if desired.

Note: Do not leave children or animals unattended

in

the vehicle when using the

quick-stop feature.

Operating the 2 I 3

Hour

The system has the ability to start the vehicle every 2 or 3 hours for a 48 hour period. This feature is especially useful engine and engine fluids warm 3 hour, selection between 2 or 3 hour

WARNING!

Be certain that the vehicle is outdoors before using this or any remote starting device. A running engine produces dangerous carbon monoxide fumes which can be harmful or fatal if prolonged exposure occurs. DO NOT remote start the vehicle if it

garaged.

Start Up Timer Mode

in

cold climates where the only means to keep the

is

to periodically start the engine. The default setting

is

made

in

is

option programming.

is

To

begin the 2

1.

I

3 hour start up timer mode:

Turn the vehicle's ignition

ON

then

OFF.

2.

3.

Press and Press the button 4 times, the system

a.

b.

To

exit the 2

4.

1.

Release the valet

I

3 hour start up timer mode:

Turn the

OR

1.

Activate the remote vehicle control.

Operating the Daily

hold

the

valet

button.

will;

When set for 3 Hour parking lights

4 times.

(default)-

chirp 2 times and flash the

When set for 2 Hour - chirp 1 time and lights

2 times.

button.

vehicle's Ignition ON.

start feature using the remote

Start

Timer

flash

the parking

The system has the

ability to start your

vehicle based on a 24-hour countdown timer.

This feature requires a two-part activation sequence. From the remote, of

the

vehicle, countdown timer (the finished operating the

pressing both the

vehicle will start 24 hours from this time). Next, When you are

vehicle

for the day, perform the

liJ

&

{)

buttons together

will

activate the 24 hour

following steps to

process.

1.

2.

Turn the ignition

Within

10 seconds,

ON/OFF (vehicle

while

pressing the brake, press and

must be disarmed).

release

button twice.

3.

Remote

For safety and security reasons, the system

vehicle

1.

2.

The

vehicle will

Start Safety

Features

emit 2 chirps and

starter from activating if any

The

vehicle

The brake

hood

pedal

is

open.

is pressed prior to turning the ignition key to the

of

the

following

flash the parking

will

shutdown or prevent the remote

lights

occur:

position.

while

ine range

complete the

the

4 times.

ON

3.

4.

6 ca5054

The engine is over-revved (tach checking Valet

mode is active.

only).

Owners rev A

Transmitter Button Functions

1 Way Transmitter

I

Lock

Unlock

ltruok

Car

Finder

Panic

Remote Remote

ShutDown

Run Time Extention

2

Daily

l

3

Hour

Start

. :<

Start

Timer

Lock

X

.

··.·

··

·

··

..

Unlock

X

Car Find I

Panic

.·

.

X

Start

X

Operation Method

Press

and Release

Press and Release

Push

and

Hofd

(3

Sec)

Press and Release

Push

and Hold (3

Press and Release depending

Push

and Hold (3 Sec)

Press and Release 4 times.

Ignition ON/OFF. Press Valet Button,

Press Lock

Sec)

(1

on

Press Start

+

Start

or 2 times

selectable option)

and Hold

4 times

Replacing Remote Control Batteries

1-Way Remote Control

The batteries (model CR2016) inside each remote year under

control

and the

normal use. When the batteries become weak you

range (the distance from the

small

LED on the remote control will

batteries:

1.

2.

Unsnap and disassemble the Remove the

and

3.

4.

Reassemble Test operation

(part#

replace

CATX4)

vehicle

old

batteries, observing

with new

the halves

of

CR2016

of

the remote

dim.

halves

batteries.

control.

control should last

will notice the remote

control will work) deteriorate

To

replace the remote

of the remote control.

the+/-

symbols on the batteries

control.

approximately 1

control

2014

Voxx

Electronics

Corporation.

All

rights reserved.

7

Code

Systems,

Inc.

Limited

Lifetime

Warranty

Code Systems Inc. ("CODE") warrants to the ORIGINAL PURCHASER

of

this CODE vehicle security product (the "Product"), purchased from an authorized CODE dealer, that (except as provided below) should this Product under normal use and conditions, be proven defective DURING THE LIFETIME OF THE VEHICLE

IN

WHICH IT WAS ORIGINALLY INSTALLED, such

in

material or workmanship

defect(s) will be repaired or replaced (at CODE's option) without charge for parts directly related to repairs

of

the defect(s).

Switches, indicator lights, and transmitter cases are similarly warranted to the original purchaser for

of

a period of one (1) year from the date of purchase

the Product.

CODE accessories, sold separately, are covered by the applicable warranty accompanying the accessory.

This warranty the vehicle installed

is

non-transferable, non-assignable and

in

which it was originally installed; or (2) the vehicle

is

transferred to another party.

is

voided when: (1) the Product

in

which the Product was originally

is

removed from

This warranty does not apply to any product damaged by accident, physical or electrical abuse, improper installation, alteration, or use contrary to its intended function, fire, flood, or other natural acts.

In

order for the Product to be repaired or replaced under the terms Product must be returned to an authorized CODE dealer and accompanied by a copy sales receipt. The date of purchase and year, make and model of the vehicle

of

this warranty, the defective

of

the retail

in

which the Product

was originally installed must be clearly indicated on the sales receipt.

is

This warranty

exclusive and CODE MAKES NO OTHER WARRANTIES EXPRESSED OR IMPLIED. ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS WRITTEN WARRANTY.

FORA

PARTICULAR PURPOSE, SHALL

IN

NO CASE SHALL CODE BE LIABLE FOR ANY CONSEQUENTIAL OR

BE

LIMITED TO THE DURATION OF THIS

INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, WHATSOEVER.

CODE does not warrant that the Product cannot be compromised or circumvented. THE EXTENT OF CODE'S LIABILITY UNDER THIS WARRANTY PROVIDED ABOVE AND,

IN

NO EVENT SHALL CODE'S LIABILITY EXCEED THE PURCHASE

IS

LIMITED TO THE REPAIR OR REPLACEMENT

PRICE PAID BY THE ORIGINAL PURCHASER OF THE PRODUCT WITHOUT INSTALLATION LABOR.

Some states do not allow the exclusion or limitation

of

incidental or consequential damages, so the above limitation may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state

8

ca5054 Owners rev A

This

product

0407,034,0580.160,5.132.660,

5.349.93'1. 5.357.560. 5.381 '128t

5.532.670, 5.534!845, 5,646.591,

5.798.711,

5.872.519, 5,898.391'

5.990.786, 6,028.732. 6.028,505,. 6.040,636. 6,043,734. 6,087,996. 6,093.,979, 6,140,914

6,

184.779.

6.462,648,

7,069,127. 7,095,314, 7,102.515. 7.135.962.

7.332.998,

is covered

5,650.774.

5,805.056,

6.218,740,

6.573.838.

7.443.285,

by

one

or

more

of

the

following U.S.

5,157,375,

5.412.371.

5,193,141,

5,467.070, 5.469,141, 5.469, 151. 5,506.568

5.563,576. 5,563,600. 5.572,185. 5,602.535,

Patents;

Other

Patents

pending.

5.245.694. 5,315.285, 5,334.969

5,614,883. 5,617.819

5.656.868. 5,673,017. 5,656.997, 5,71.2,638. 5.783,988, 5,783.989

5.819,568, 5,900,806. 5,905,431. 5,907,195. 5,914,667,

6,2

.

59,

6.697,719,

5.828~316.

169, 6,285·.296.

6,700.479. 6,781,507. 6,828.901,

5,838,255.

6,288.635

.. 6,317,034. 6.452,483. 6.452.484

5,850,173,

5,850, 174, 5,855,050

5,945,936. 5,952.933

6.982.631.

7,030,739

7,142.097, 7.191.053, 7.243,007. 7,248.150

7,463,135, 7.483.783.

7,519.400,

7.532,959. 7,616,099.

7,646.285

7.653,463, 7.962.260. 8.380.430.

2014

Voxx

Electronics

Corporation.

All

rights reserved.

9

10

ca5054 Owners

rev A

2014

Voxx

Electronics

Corporation. All

rights reserved.

11

Voxx

Electronics

Corporation.

FCC

COMPLIANCE

This device

Customer Service

WWW.CODE-ALARM.COM

complies

with Part 15 of the

1-800-421-3209

FCC rules

and with

RSS-21 0

of

Industry Canada. Operation

1.

This device may not cause harmful

2.

This device must accept any interference received,

may cause undesired operation.

Warning!

Changes

or modifications not

compliance could void the user's authority to operate the equipment.

12

is

subject to the

following

two conditions:

interference, and

including

expressly approved by the party

R41

0-192-700

any interference that

responsible

ca5054

for

Owners

rev A

WARNING

THIS

VEHICLE IS EQUIPPED WITH

A REMOTE

CONTROLLED

CAR STARTER

BEFORE

SERVICING THIS VEHICLE, REMOVE THE MAIN

POWER

FUSE (RED

WIRE) TO

THE

CAR STARTER

OR

DISCONNECT

THE

VEHICLE

BATTERY.

LBL0675