Page 1
1ca1151 rev B. 201 1 Audiovox Electronics Corporation. All right s reserved.
PROFESSIONAL
SERIES
Security and Keyless Entry
Installation Guide
ca 1151
Page 2
2 ca1151 rev B. 201 1 Audiovox Electronics Corporation. All rights reserved.
Before You Begin ......................................................................................3
Wire Connection Guide ...........................................................................4
6 Pin Main Harness ................................................................................... 5
6 Pin Input / Output Harness ....................................................................6
3 Pin AUX Output Harness .......................................................................8
6 Pin Door Lock Output Harness ............................................................. 9
Additional Ports ...................................................................................... 10
LED Port...................................................................................................10
Programming Port....................................................................................10
Shock Sensor Port..................................................................................10
DBI Port....................................................................................................10
Set Up & Programming .......................................................................... 11
Transmitter Programming........................................................................ 11
Manual Feature Programming................................................................. 11
Programming Feature Banks .................................................................. 12
Adjusting the Shock Sensor .................................................................. 13
Testing the Shock Sensor ......................................................................13
Chirp Delete - User Accessible ..............................................................13
Dome Light Delay / Theater Dimming .....................................................13
Feature Descriptions .............................................................................14
Transmitter Button Functions ............................................................. 16
Security Trigger Zones .........................................................................17
System Layout .........................................................................................18
Table of Contents
Page 3
3ca1151 rev B. 201 1 Audiovox Electronics Corporation. All right s reserved.
PROFESSIONAL INST ALLA TION
STRONGLY RECOMMENDED
Installation Precautions:
Roll down window to avoid locking keys in vehicle
during installation
Avoid mounting components or routing wires near
hot surfaces
Avoid mounting components or routing wires near
moving parts
Tape or loom wires under hood for protection and
appearance
Technical Support (800) 421-3209
or go to
http://techservices.codesystems.com
Use a Digital Multi Meter for testing and verifying
circuits. DO NOT USE A TEST LIGHT, OR
"COMPUTER SAFE PROBE" as these can set off air
bags or damage vehicle computers.
Use grommets when routing wires through metal
surfaces
BEFORE YOU BEGIN
Page 4
4 ca1151 rev B. 201 1 Audiovox Electronics Corporation. All rights reserved.
3 Pin AUX Output Harness
6 Pin Input / Output Harness
6 Pin Main Harness
6 Pin Door Lock Output Harness
Page 5
5ca1151 rev B. 201 1 Audiovox Electronics Corporation. All right s reserved.
4 BLACK GROUND
Connect the BLACK wire to a solid chassis ground point using a ring terminal and
self tapping screw (not supplied). Scrape away paint from the grounding point to
ensure a good connection. The recommended grounding point is a metal surface
in the driver’s side kick panel area.
NOTE: Do not ground the BLACK wire with any other vehicle components.
6 Pin Main Harness
1 WHITE PARKING LIGHT OUTPUT
2 WHITE/RED PARKING LIGHT INPUT
3 WHITE PARKING LIGHT OUTPUT
Locate the parking light output wire at the vehicle’s light switch.
Verification: This wire registers positive voltage when the parking lights
are turned on.
Positive switching Parking Lights:
Connect the WHITE/RED wire to a 15 Amp max fused battery source.
Connect the WHITE wire to the parking light output wire.
Negative switching Parking Lights:
Connect the WHITE/RED wire to a good chassis ground.
Connect the WHITE wire to the parking light output wire.
5 BROWN SIREN OUTPUT ( + )
Locate a suitable mounting location in the engine compartment for the siren, away
from moving parts.
With the bell of the siren aiming downwards, secure the siren in place using self
tapping screws, being careful not do drill into any hoses, wiring or components.
Connect the BLACK siren wire to a chassis ground using a ring terminal and self
tapping screw (not supplied).
Route the BROWN siren output wire from the control module through the firewall
and connect to the RED wire on the siren.
NOTE: Be sure to loom the siren wires, and seal the grommet.
Page 6
6 ca1151 rev B. 201 1 Audiovox Electronics Corporation. All rights reserved.
6 RED BATTERY 12V ( + )
Locate 1 of the vehicle’s constant 12 Volt battery wires at the ignition switch.
Verification: This wire will register ( + ) voltage in all positions of the ignition
switch.
Connect the RED wire to the constant 12 Volt battery wire.
NOTE: Remove all fuses until all connections are made.
6 Pin Input / Output Harness
1 PURPLE DOOR TRIGGER INPUT ( + )
Locate the vehicle’s dome light or door pin switch wire.
Verification: This wire will register positive voltage (POS) when the door is
opened and the interior light is on. This wire will
register ground or "0" Volts when the door is closed and the interior light is
off.
Connect the PURPLE wire to the vehicle’s positive door input wire(s).
NOTE: Certain vehicles may require multiple connections. Refer to vehicle
application guide
2 GRAY HOOD PIN INPUT ( - )
Install a Hood Pin Switch and connect to the GRAY wire.
Verification: This wire when connected will register ground when the
vehicle's hood is opened.
Connect the GRAY wire to the hood pin.
NOTE: Be sure to loom the wire, and seal the grommet.
Page 7
7ca1151 rev B. 201 1 Audiovox Electronics Corporation. All right s reserved.
5 ORANGE GROUND WHEN ARMED OUTPUT ( - )
This wire will have a continuous ( - ) 300mA output when the system is Armed. This
wire is typically used for controlling window modules or additional sensors.
4 YELLOW IGNITION INPUT ( + )
Locate the vehicle’s ignition wire at the ignition switch.
Verification: This wire registers voltage when the key is turned to the ON (or
RUN) position. The voltage does not drop out when the key is turned to the
START (or CRANK) position.
Connect the YELLOW wire to the vehicle’s Ignition wire.
6 RED/WHITE TRUNK RELEASE OUTPUT ( - )
Locate the vehicle’s trunk release wire at the trunk release switch.
Verification: This wire will register either positive voltage or ground when
the trunk release is activated.
This is a low current output, 300mA.
3 GREEN DOOR TRIGGER INPUT ( - )
Locate the vehicle’s dome light or door pin switch wire.
Verification: This wire will register ground (NEG) when the door is opened
and the interior light is on. This wire will register positive voltage when the
door is closed and the interior light is off.
Connect the GREEN wire to the vehicle’s negative door input wire(s).
NOTE: Certain vehicles may require multiple connections. Refer to vehicle
application guide
Page 8
8 ca1151 rev B. 201 1 Audiovox Electronics Corporation. All rights reserved.
1 VIOLET/BLACK AUX 1 OUTPUT ( - )
This wire provides a ( - ) 300mA output capable of driving relays. For Control of
optional accessories (i.e. Power Window/Sunroof, etc.).
To activate refer to the transmitter button configuration chart. Please refer to the
selectable options for timing.
3 BROWN/BL ACK HORN OUTPUT ( - )
Locate the vehicle’s horn wire.
Verification: This wire will register at positive voltage and register
ground when the horn switch is pressed.
Connect the BROWN/BLACK wire to the vehicle’s horn wire. This is a low current
output, 300mA.
3 Pin AUX Output Harness
2 GREEN/BLACK FACTORY DISARM ( - )
This wire will supply a ( - ) 300mA pulse both upon disarming the system and
when the trunk release feature is activated. Locate the factory perimeter alarm
disarm wire from the key cylinder inside the drivers door.
Verification: This wire registers ground if the key is turned to the unlock
position in the driver’s door cylinder.
Connect the GREEN/BLACK wire to the factory alarm disarm wire.
Page 9
9ca1151 rev B. 201 1 Audiovox Electronics Corporation. All right s reserved.
6 Pin Door Lock Output Harness
1 BROWN/B LACK UNLOCK SWITCH ( 87A )
2 BLUE/BLACK UNLOCK MOTOR ( 30 )
3 VIOLET/BLACK UNLOCK POLARITY ( 87 )
4 WH IT E/ BL AC K LOCK SWITCH ( 87A )
5 GREEN/BLACK LOCK MOTOR ( 30 )
6 VIOLET LOCK POLARITY ( 87 )
The door lock / unlock outputs are designed to control several different types of
systems which may require additional parts.
3 Wire Ground Switched Door Locks:
Connect the GREEN/BLACK wire to the wire that provides a ground signal from
the factory door lock switch to the factory door lock control relay.
Connect the BLUE/BLACK wire to the wire that provides a ground signal from the
factory door unlock switch to the factory door lock control relay.
Connect the VIOLET and the VIOLET/BLACK wires to a solid chassis ground
point. The WHITE/BLACK and BROWN/BLACK wires are not required for this type
of door lock/unlock system.
3 Wire Positive Switched Door Locks:
Connect the GREEN/BLACK wire to the wire that provides a +12 volt signal from
the factory door lock switch to the factory door lock control relay.
Connect the BLUE/BLACK wire to the wire that provides a +12 volt signal from
the factory door unlock switch to the factory door lock control relay.
Connect the VIOLET and the VIOLET/BLACK wires to a +12 volt battery source.
The WHITE/BLACK and BROWN/BLACK wires are not required for this type of
door lock/unlock system.
Page 10
10 ca1151 rev B. 201 1 Audiovox Electronics Corporation. All rights reserved.
Data Bus Interface Port
This 4 pin port is used for Flashlogic Door Lock and Transponder Databus
Interfaces to communicate with the vehicle's Databus. When using the DBI port to
control the Flashlogic Door Lock and Transponder Interface modules the
following options may be available. Please refer to the D2D (Data to Data)
function list available per vehicle on the tech service web site.
Door Trigger
Trunk/Hatch Open Door Lock Control
Dome Light Supervision Factory Alarm Arm / Disarm
Manual Arm / Disarm Inputs (factory keyless controls system)
LED Port
The LED included in the kit will serve as a visual indicator of the alarm’s status. It
should be installed in the dash, located where it can be easily seen from outside
the vehicle, yet not be distracting to the driver. Once a location has been
selected, check behind the panel for wire routing access, and to confirm the drill
will not damage any existing components as it passes through the panel. Drill a
1/4" hole, and pass the red and blue wires from the LED through the hole, from
the front of the panel. Firmly press the body of LED into the hole until fully seated.
Additional Ports
Programming / Valet Button Port
Select a mounting location that is within reach of the ignition switch, as this
switch in combination with the ignition switch, will be used to program the certain
features of the system. It is suggested that the switch be mounted to the lower
dash panel in the driver’s area within reach of the driver.
Shock Sensor Port
Select a solid mounting surface for the shock sensor inside the passenger
compartment (behind the dash), and mount the sensor using cable ties, making
sure to allow access to the sensitivity adjustment for use later in the installation.
Page 11
11ca1151 rev B. 201 1 Audiovox Electronics Corporation. All right s reserved.
Manual Feature Programming - Feature Bank 2 & 3
1. Turn the ignition ON.
2. Press and hold the valet/override button.
3. Within 10 seconds the system will chirp (3) three times.
4. Use the valet/override button to advance through each option bank. For
feature programming advance to Feature Bank 2 or 3, which is (4) four or
(5) five chirps.
5. Use the transmitter button to scroll through the selections in each
feature bank, the system will chirp to match the feature number.
6. Press the transmitter button to change the desired feature. The LED will
flash indicating the changed feature.
Set Up & Programming
Transmitter Programming - Feature Bank 1
1. Turn the ignition ON.
2. Press and hold the valet/override button.
3. Within 10 seconds the system will chirp (3) three times.
4. Press 1 button of each transmitter you wish to program.
5. The system will respond with 1 chirp for each accepted transmitter.
6. Pressing the override button at anytime during programming will advance to
the next bank.
NOTE: The system will exit transmitter programming after 15 seconds of inactivity.
NOTE: This system has 1 button programming which programs all channels of the
system.
NOTE: The system will hold up to 4 transmitters in memory, programming a 5th
transmitter will erase the oldest transmitter in memory.
Page 12
12 ca1151 rev B. 201 1 Audiovox Electronics Corporation. All rights reserved.
Feature Bank 1 -
3 Chirps
Transmitter Programming
Refer to transmitter programming.
Defaulting All Features: Pressing the button anytime while in any of the
feature banks will default all features and return you to feature bank 2 - 4 chirps.
NOTE: The system will remain in feature programming mode as long as the
ignition is on, there is no time limit. To exit programming turn the IGNITION OFF .
Feature Bank 2 -
4 Chirps
Security Control
1 LED Flash 2 LED Flash 3 LED Flash 4 LED Flash 5 LED Flash
1 Silent Choice ON
OFF
2 Passive Locks
Active
Passive
3 Passive Arming
Active
Passive
4 Siren / Horn ARM/DISARM Chirps
Siren /Horn
Siren Horn
5 Siren Duration
30 Seconds
60 Seconds
6 Security
ON
OFF
7 Anti-Hijack Mode
OFF
ON
Feature Bank 3 -
5 Chirps
Output Control
1 LED Flash 2 LED Flash 3 LED Flash 4 LED Flash 5 LED Flash
1 Extended Lock Pulse
1 Second
3.5 Seconds
1 Second Lock,
Double Pulse
Unlock
30 Second
Lock, Double
Pulse Unlock
Double Pulse
Lock, 1 Second
Unlock
2 Factory Disarm
Factroy
Disarm
2nd Unlock
3 Ignition Controlled Locks
OFF
Lock and
Unlock
Lock Only Unlock Only
4
Trunk Output Timing
Red / White Output
Push and Hold
10 Seconds 20 Seconds
Latched until
IGN ON
Latched ON
until Button
Press
5 Horn Output Timing
16mS
10mS 30mS 40mS 50mS
6 Real Panic
ON
OFF
7
AUX 1
Violet / Black Output
Push and Hold
Latched
Latched until
IGN ON
Dome Light
Output
Page 13
13ca1151 rev B. 201 1 Audiovox Electronics Corporation. All right s reserved.
Dome Light Delay / Theater Dimming
The system can be programed to delay arming after the lock button is pressed (60
second max) for vehicles with a dome light delay or theater dimming feature. Once
programed the system will ‘learn’ the timing of the dome light delay and add 2
seconds before arming.
1. Close all doors with ignition off.
2. Using the transmitter press LOCK, UNLOCK, LOCK ,UNLOCK, LOCK ,
UNLOCK, LOCK. The LED will light solid to indicate the system has
entered DOME DELA Y LEARN MODE.
3. Immediately OPEN then CLOSE the door WITHOUT disarming the
system. The system will then monitor the door trigger wire. Once the
dome light turns off, the system will then add 2 seconds and then exit
the learning mode.
4. The LED will begin to flash indicating the system has exited the
learning mode and is now armed.
Chirp Delete - User Accessible
System ARM/DISARM chirps can be toggled ON or OFF without entering the
programming feature banks.
1. Turn the ignition ON then OFF.
2. Press and release the valet/programming button 3 times. The system
will respond with 1 chirp for ON or 2 chirps for OFF.
Adjusting the Shock Sensor
1. Increase sensitivity by turning the adjustment dial clockwise.
2. Decrease sensitivity by turning the adjustment dial counter clockwise.
T esting the Shock Sensor
Arm the system and wait 6 seconds for the zone to stabilize, then firmly strike
the vehicles bumper.
Page 14
14 ca1151 rev B. 201 1 Audiovox Electronics Corporation. All rights reserved.
2 - Passive Locks: Determines manual or automatic locking of the vehicle’s
doors.
Active - Requires use of the transmitter to lock the vehicle’s doors.
Passive - Automatically locks the vehicle’s doors 1 minute after the last door
is closed
3 - Passive Arming: Determines manual or automatic locking of the vehicle’s
doors.
Active - Requires use of the transmitter to arm the security system.
Passive - Automatically arms the security system 1 minute after the last door
is closed
4 - Siren / Horn: This feature selects which output(s) will sound the system’s
arm/disarm chirps. This feature does not effect the triggered state of the security
system and during a triggered cycle, both the siren and horn outputs will activate
respectively.
5 - Siren Duration: Determines the length of time the system will sound the
siren/horn during a full trigger event.
6 - Security: Controls security functionality - ON / OFF.
ON - Full security functionality.
OFF - The security system does not trigger. Panic and all other convenience
features operate as normal.
7 - Anti-Hijack Mode: Controls Car Jack mode - ON / OFF.
OFF - Standard security system operation.
ON - Enables Car Jack mode functionality as described in the owners
manual
Feature Bank 2 - Security
1 - Silent Choice: Controls the normal arm/disarm chirps of the security system.
ON - Silent arming/disarming upon first press of lock/unlock, pressing lock/
unlock a second time will activate the arm/disarm chirps respectively. The
system will only sound the arm/disarm chirps upon a second press of the
lock/unlock buttons.
OFF - normal arm/disarm chirps upon the first press of lock/unlock.
Feature Descriptions
Page 15
15ca1151 rev B. 201 1 Audiovox Electronics Corporation. All right s reserved.
Feature Bank 3 - Output Control
1 - Extended Lock Pulse: Controls the timing of the BLUE and GREEN lock
output wires.
1 Second - Single 1 second lock pulse, single 1 second unlock pulse.
3.5 Seconds - Single 3.5 second lock pulse, single 3.5 second unlock pulse.
1 Second Lock, Double Pulse Unlock - Single 1 second lock pulse, double 1
second unlock pulse.
30 Second Lock, Double Pulse Unlock - Single 30 second lock pulse, double
1 second unlock pulse.
Double Pulse Lock, 1 Second Unlock - Double 1 second lock pulse, single 1
second unlock pulse.
2 - Factory Disarm: Controls the timing of the LT. GREEN/BLACK factory disarm
output.
Factory Disarm - Single 1 second pulse with unlock and remote start
activation.
2nd Unlock - Same output as unlock with 2nd press of unlock only.
3 - Ignition Controlled Locks: Control of door locks when the ignition is cycled
ON or OFF.
OFF - Door locks not activated by ignition.
Lock and Unlock - Doors lock when ignition is turned on and unlock when
ignition is turned off.
Lock Only - Doors lock when ignition is turned on.
Unlock Only - Doors unlock when ignition is turned off.
4 - Trunk Output Timing - Red/White Output: Control of the RED/WHITE trunk
release output wire when trunk release is activated from the transmitter.
Push and Hold - Output is continuously active until transmitter button is
released.
10 Seconds - Output stays active for 10 seconds regardless of length
button press on transmitter.
20 Seconds - Output stays active for 20 seconds regardless of length
button press on transmitter.
Latched until IGN ON - Output stays active until the ignition is turned on.
Latched ON until Button Press - Output stays active until deactivated by
transmitter.
Page 16
16 ca1151 rev B. 201 1 Audiovox Electronics Corporation. All rights reserved.
T ransmitter Button Functions
7 - AUX 1 - Violet/Black Output: Controls the VIOLET/BLACK AUX 1 output
activation type and timing.
Push and Hold - Output is continuously active until transmitter button is
released.
Latched - Output stays active until button is pressed again.
Latched until IGN ON - Output stays active until the ignition is turned on.
Dome Light Output - Output is used for illuminated entry and is not controlled
by the AUX 1 function of the transmitter.
5 - Horn Output Timing: Control the minimum horn pulse time in milli seconds,
some vehicle will require a longer pulse to activate the factory horn.
16mS 10mS 30mS 40mS 50mS
6 - Real Panic: Controls the panic out when triggered from the transmitter.
ON - Randomized horn honks when panic is triggered.
OFF - Standard pattern horn honks when panic is triggered.
Page 17
17ca1151 rev B. 201 1 Audiovox Electronics Corporation. All right s reserved.
Security T rigger Zones
If the security system has been triggered the LED will flash one of the patterns
below indicating the zone.
LED FLASHESTRIGGER ZONE
2 Flashes Hood / Trunk Input
3 Flashes Door Input
4 Flashes Shock Sensor
5 Flashes Ignition Input
Page 18
18 ca1151 rev B. 201 1 Audiovox Electronics Corporation. All rights reserved.
VIOLET/BLACK AUX 1 OUTPUT ( - )
GREEN/BLACK FACTORY DISARM OUTPUT ( - )
BROWN/BLACK HORN OUTPUT ( - )
PURPLE DOOR TRIGGER INPUT ( + )
GRAY HOOD PIN INPUT ( - )
GREEN DOOR TRIGGER INPUT ( - )
YELLOW IGNITION INPUT ( + )
ORANGE ARMED OUTPUT ( - )
RED/WHITE TRUNK RELEASE OUTPUT ( - )
WHITE PARKING LIGHT OUTPUT
WHITE/RED PARKING LIGHT INPUT
WHITE PARKING LIGHT OUTPUT
BLACK GROUND
BROWN SIREN OUTPUT ( + )
RED BATTERY 12V ( + )
BROWN/BLACK UNLOCK SWITCH ( 87A )
BLUE/BLACK UNLOCK MOTOR ( 30 )
VIOLET/BLACK UNLOCK POLARITY ( 87 )
WHITE/BLACK LOCK SWITCH ( 87A )
GREEN/BLACK LOCK MOTOR ( 30 )
VIOLET LOCK POLARITY ( 87 )
SHOCK SENSOR PORT
PROGRAMMING / VALET PORT
LED PORT
DBI PORT
CA 1151
Page 19
19ca1151 rev B. 201 1 Audiovox Electronics Corporation. All right s reserved.
Page 20
20 ca1151 rev B. 201 1 Audiovox Electronics Corporation. All rights reserved.
Audiovox Electronics Corporation.
Customer Service 1-800-421-3209
WWW.CODE-ALARM.COM
FCC COMPLIANCE
This device complies with Part 15 of the FCC rules and with RSS-210 of
Industry Canada. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including any interference
that may cause undesired operation.
Warning!
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Loading...