Code XML02 Users Manual

CodeXML M3 Bluetooth® Modem Installation with USB Cable

Cable Installation

Attach the end of the USB cable to the CodeXML M3 Bluetooth® Modem (Figure

2). Connect the USB connector to the host computer (Figure 3). Once connected

the modem’s blue LED light will turn on.

Figure 2

Figure 3

Establish Mode

Scan the USB Mode code (M708_01-right). You are ready to
begin reading bar codes and transmitting decoded data to the host

computer.

Connecting with QuickConnect Code

See instructions on page 3 for establishing a paired connection between the
modem and the host computer.

USB Cable installed to CodeXML M3
Bluetooth® Modem

USB Mode

Connecting with QuickConnect Code (for all cable types):

Scan the QuickConnect Code on the label of the CodeXML M3 Bluetooth®
Modem using the Code reader with which you wish to establish a paired
connection to a host computer. The reader and host computer should easily

connect within 60 seconds. The Code reader will beep once and ash both LEDs
green as conrmation. If the reader and computer do not connect, the reader will
beep three times in rapid succession and ash red LEDs.

Modem Firmware Version Output & Values (for reference only):

For All Readers:

Scan to View

Firmware Version

VVVVvvvvCKP BaudString:

VVVV 4 digit rmware version (MSP430 rmware version)
vvvv 4 digit rmware version (TUSB rmware version)
C 1 digit comm mode: 1=RS-232, 2=Wand Emul., 3=USB

KBD

K Keyboard Map, same as reader host ICD setting 0x2d
P 1 digit packet protocol: 0=Raw, 1=SPX packet, 2=Code

Reader packet, 4=Encrypted Packet Format, 5= Protocol

Version (AES)

BaudString spx: Baud:DataBitsParityStopbits

CodeXML M3 Bluetooth® Modem
Important Note:

The CodeXML Modem has been tested for compliance with FCC regulations and was found to be compliant

with all applicable FCC Rules and Regulations. FCC ID#: QQ6-XML02
Model #: BTHDG-M3-RO-CX

Keyboard Input (USB)

The modem is defaulted to English language keyboards. If you need to
communicate in a different language requiring a change in keyboard settings,

please scan the appropriate code below:

English (Default) Universal French German

Japanese

2 C003996_01_CodeXML_M3_Modem_Quickstart

Non-printable ASCII Keyboard
(No Leading 0)

Non-printable ASCII
Keyboard (Crtl + character)

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Any changes made by the user not approved by Code Corporation can void the user’s authority to operate the
equipment.

To satisfy FCC RF exposure requirements for mobile transmitting devices, a separation of 20 cm or more

should be maintained between the antenna of this device and persons during device operation. To ensure

compliance, operations at closer than this distance are not recommended. The antenna used for this

transmitter must not be co-located in conjunction with any other antenna or transmitter.

C003996_01_CodeXML_M3_Modem_Quickstart 3

CodeXML M3 Blueooth® Modem Installation with RS232

Cable Installation

Attach the end of the RS-232 cable (pictured below) to the CodeXML M3
Bluetooth Modem (Figure 7). Connect the RS-232 adapter to the back of your
computer (Figure 8). Connect the RS-232 cable to the power supply (Figure

9). Plug the power supply into a wall socket (Figure 10). Once connected the

Modem’s blue LED light will turn on.

Quickstart Guide

CodeXML M3 Bluetooth® Modem ­Multiple Interface Unit (MIU)

The CodeXML M3 Bluetooth® MIU Modem is an external modem designed

to be connected to the host computer in use with a Code reader (CR2 or
CR3). The Modem enables a reader to wirelessly transmit captured and
decoded data to its host computer. The Modem can accommodate cabled
attachment with two connector types (Figure 1).

Figure 7 Figure 8

Figure 9

Figure 10

Connecting with QuickConnect Code

See Page 2 for instructions to establish a paired
connection between the Modem and the host
computer.

Establish Mode

Scan the RS-232 Mode code (M661_01-right).
You are ready to begin reading bar codes and
transmitting decoded data to a host computer with
any open software application that accepts data

from RS-232/Serial input

Change Baud Rate Settings: Scan the

RS-232 Mode

appropriate code below:

Note: These codes only affect Baud Rate for the
modem and do not affect any settings on Code Readers.

1200 2400 4800 9600 (Default)

RS-232 Cable (Left) - CodeXML M3
Bluetooth® Modem (Center) - Power
Supply (Right)

Default Modem

settings:

Baud Rate: 9600
Stop Bits: 8
Parity: None
Stop Bits: 1

Hardware: None

Figure 1

CodeXML M3 Bluetooth®Modem MIU

The CodeXML M3 Bluetooth® Modem is ‘plug & play.’ You simply plug­in the Modem and start transmitting data from Code readers without
downloading any drivers or software. The Modem can receive Bluetooth
signals from up to 300 feet (100 meters) away.

19200 38400 57600 115200

4 C003996_01_CodeXML_M3_Modem_Quickstart

For assistance, contact Code Technical Support at: [phone]; or by

email: [e-mail]

C003996_01_CodeXML_M3_Modem_Quickstart 1