Code Two-Bay Battery Charger User Manual
Charging a Battery Cartridge:
Charging a Battery Cartridge:
Figure 3
Figure 5
Charging Status:
To charge a battery, install 2 two plastic inserts into
a charging bay. (Figure 3)
Press down rmly on the inserts, until you hear
them click into place. (Figure 4)
Figure 4
Place the battery cartridge, with the manufacturer
label facing forward, into the charging bay.
(Figure 5)
To charge a battery, install 2 two plastic inserts into
a charging bay. (Figure 3)
Press down rmly on the inserts, until you hear
them click into place. (Figure 4)
Figure 3
Figure 4
Place the battery cartridge, with the manufacturer
label facing forward, into the charging bay.
(Figure 5)
Figure 5
Charging Status:
Each charging bay has an LED light to indicate the charging status of the battery or
reader. Once the reader, or battery, is engaged with the charging clips - the LED light
associated to that charging bay will light up. (Figure 6)
Each charging bay has an LED light to indicate the charging status of the battery or
reader. Once the reader, or battery, is engaged with the charging clips - the LED light
associated to that charging bay will light up. (Figure 6)
A red LED = reader/battery is charging
A green LED = reader/battery is fully charged*
*Note: In certain reader congurations, the radio is required to
always on, therfore requiring a constant power draw. In these
instances, while the power draw is minimal, the LED light may
never turn green when charging a battery attached to a reader.
Figure 6
14870 S. Pony Express Rd. #200 Bluffdale, UT 84065
www.codecorp.com (801) 495-2200
C001529_07_TwoBayBatteryCharger_Quickstart C001529_07_TwoBayBatteryCharger_Quickstart
© 2012 Code Corporation. All rights reserved.
Figure 6
A red LED = reader/battery is charging
A green LED = reader/battery is fully charged*
*Note: In certain reader congurations, the radio is required to
always on, therfore requiring a constant power draw. In these
instances, while the power draw is minimal, the LED light may
never turn green when charging a battery attached to a reader.
14870 S. Pony Express Rd. #200 Bluffdale, UT 84065
www.codecorp.com (801) 495-2200
© 2012 Code Corporation. All rights reserved.
Quickstart Guide
Quickstart Guide
Two-Bay Battery Charger
The Two-Bay Battery Charger features two
charging bays that can accomodate either two
bar code readers (CR2 or CR2500) or two
battery cartridges. You can also charge one of
each, as pictured in Figure 1.
Figure 1
Included:
Charger and Power Supply
4 plastic inserts for use when charging
battery cartridges.
Two-Bay Battery Charger
The Two-Bay Battery Charger features two
charging bays that can accomodate either two
bar code readers (CR2 or CR2500) or two
battery cartridges. You can also charge one of
each, as pictured in Figure 1.
Figure 1
Included:
Charger and Power Supply
4 plastic inserts for use when charging
battery cartridges.
To begin, plug the power cord into the back of the charger, and plug the adapter into a wall socket.
Charging a CR2 or CR2500 bar code reader:
To charge a reader, simply place the reader,
facing forward, into a charging bay. (Figure 2)
Note: Fully charge batteries before rst use.
The approximate charge time is 4 hours.
Figure 2
To begin, plug the power cord into the back of the charger, and plug the adapter into a wall socket.
Charging a CR2 or CR2500 bar code reader:
To charge a reader, simply place the reader,
facing forward, into a charging bay. (Figure 2)
Note: Fully charge batteries before rst use.
The approximate charge time is 4 hours.
Figure 2
Loading...