Cocoon IT315007 Instruction Manual

INSTRUCTION MANUAL

Model Number: IT315007

QUADCOPTER WITH HD CAMERA

Record your flight in HD

Warranty Note

If you experience any issues with this product, or it’s
performance is not what you had expected, please contact
us at Winplus before returning the item to the store.

It is likely that we can resolve any problems for you via
phone or email.

We can be reached on:

Phone: [phone] (Mon - Fri; 8:30am - 6:00pm EST)
Email: [e-mail]
Web: www.winplus.com.au

Warranty Details

The product is guaranteed to be free from defects in workmanship and parts for a period
of 12 months from the date of purchase. Defects that occur within this warranty period,
under normal use and care, will be repaired, replaced or refunded at our discretion.
The benefits conferred by this warranty are in addition to all rights and remedies in respect
of the product that the consumer has under the Competition and Consumer Act 2010 and
similar state and territory laws.

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law.
You are entitled to a replacement or refund for a major fail

ure and for compensation
for any other reasonably foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the failure
does not amount to a major failure.

AFTER SALES SUPPORT

YEAR WARRANTY

1

MODEL: IT315007 PRODUCT CODE: 51176 09/2015

[e-mail]

1300 663 907

AUS

VOYAGER QUADCOPTER

5

After Sales Support

1300 663 907

Model Number IT315007

[e-mail]

Safety Instructions

Follow all instructions and take notice of all warnings to reduce risk of re or electric shock.

• Read the instructions in this manual thoroughly before operating your Voyager Quadcopter.

• This Voyager Quadcopter must be operated safely at all times. It is the operator’s responsibility

to always y in safe conditions.

• Always check each component of the Voyager Quadcopter is operating correctly before ying.

• Always follow local aviation rules and regulations when ying the Voyager Quadcopter.

• This Voyager Quadcopter is designed for ages 14+.

• Adult supervision is always advisable with any form of ying toy.

• Always ensure your ight area is safe.

• If a problem occurs with the Voyager Quadcopter, always contact the supplier before attempting

to y again.

• Do not y in windy, rainy or low light conditions.

Winplus Australasia will not take any responsibility for incorrect use of the Voyager Quadcopter.

Rules & Regulations

The following regulations must be followed when operating your Voyager Quadcopter in Australia.

• You must only operate this aircraft in your line-of-sight in daylight.

• You must not y closer than 30 metres to vehicles, boats, buildings or people.

• You must not y over populous area, such as beaches, other people’s backyards, heavily

populated parks, or sports ovals where there is a game in progress.

• If you are in controlled airspace, which covers most Australian cities, you must not y higher

than 120 meters (400 feet).

• You should not y within 5.5 km of an aireld.

• It’s illegal to y for money or economic reward unless you have an unmanned operator’s

certicate issued by the Civil Aviation Safety Authority (CASA).

Source: http://www.casa.gov.au/wcmswr/_assets/main/lib100071/ying_with_control_model.pdf

It is the Voyager Quadcopter operator’s responsibility to regularly check and obide by the current

rules and regulations.

Incorrect operation of this Voyager Quadcopter may result in severe injury, loss of property or nes.

Winplus Australasia does not take any responsibility if local rules and regulations are not followed.

6

After Sales Support

1300 663 907

Model Number IT315007

[e-mail]

Contents

Warranty Details 4

Safety Instructions 5

Rules & Regulations 5

Parts List 7

Technical Specications 7

Features 7

Product Overview 8

1.1 Voyager Quadcopter 8

1.2 Remote Control - Buttons 8

1.3 Remote Control - Display 9

Installation 10

2.1 Installing the Control Batteries 10

2.2 Charging and Inserting the Voyager Quadcopter Battery 10

2.3 Installing Landing Skids and Blade Guards 11

2.4 Safe Flight Environment 11

2.5 Pairing the Voyager Quadcopter with the Remote 11

Operation 12

3.1 Flying the Voyager Quadcopter 12

3.2 Fine Tuning 13

3.3 Using the Camera 13

3.4 Speed Control 14

3.5 Tricks 14

3.6 Mid Air Start 14

3.7 Changing to Mode 2 14

3.8 Mode 2: Flying 15

3.9 Mode 2: Fine Tuning 15

3.10 Resetting the Voyager Quadcopter 16

3.11 Replacing Propellor Blades 16

FAQs 17

Repair and Refurbished Goods or Parts Notice 18

Flight Log 19

7

After Sales Support

1300 663 907

Model Number IT315007

[e-mail]

Parts List

Technical Specications

Features

1 x Voyager Quadcopter

1 x Remote Control

4 x Replacement Propeller Blades

4 x Blade Guards

1 x Screwdriver

1 x USB Charging Cable

4 x ActivEnergy AA Batteries

1 x Instruction Manual

1 x Getting Started Guide

1 x Warranty Card

Voyager Quadcopter Input: 3.7V, 500 mAh

Voyager Quadcopter Battery Type: Lithium-Ion

Charging time: 75 minutes (USB recharge)

Flying time: 7 minutes

Remote range: 50 meters

Frequency: 2.4 GHz (4 channel)

Video Resolution: 720P

Image Resolution: 3.6MP

Low-voltage protection: If the Voyager Quadcopter’s battery gets too low, the rotors will stop,

protecting the battery from damage.

Over-current protection: If the Voyager Quadcopter’s blades become jammed, the control will stop

supplying power to the rotors automatically.

3D Eversion: Built-in functions allow you to perform advanced manoeuvres with ease.

6-Axis Gyroscope: Ensure the Voyager Quadcopter remains steady when ying.

8

After Sales Support

1300 663 907

Model Number IT315007

[e-mail]

1

2

3

Product Overview

1.1 Voyager Quadcopter

1.2 Remote Control - Buttons

1. Camera 2. Propeller Guards 3. Landing Skids

1. High/Low Speed Button

2. Antenna

3. Indicator

4. Left Control Stick

5. Photo/Video Switch

6. Left Tuning Switch

7. On/O Switch

8. Trick Button

9. Right Control Stick

10. Forward/Back Trim

11. Mode Switch

12. LCD Display

5

6

11

12

7

8

1

2 3

4

9

10

9

After Sales Support

1300 663 907

Model Number IT315007

[e-mail]

Product Overview

1.3 Remote Control - Display

1. Signal Indicator

2. Mode Indicator

3. Turn Left

4. Throttle Lever Fine-

tuning

5. Throttle

6. Right

7. Backward

8. Turn Left/Right Fine-

tuning

9. High/Low Speed

Indicator

10. Control Battery Level

11. Turn Right

12. Forward/Backward Fine-

tuning

13. Throttle

14. Left

15. Sideways Fine-tuning

1 9

2 10

5 13

3 11

6 14

8

7 15

4 12

10

After Sales Support

1300 663 907

Model Number IT315007

[e-mail]

Installation

2.1 Installing the Control Batteries

1. Use a screwdriver to remove the screw on the back of the remote control, then open the

battery cover.

2. Install 4x AA batteries into the back of the remote control. Please note the polarity positions

indicated.

3. Replace the cover and reinstall the screw.

Note: For best performance, do not mix dierent types of batteries.

2.2 Charging and Inserting the Voyager Quadcopter Battery

1. Push the on/o switch of the Voyager Quadcopter to o, then open

the battery cover.

2. Pull out the battery wire from the power port and remove battery.

3. Insert the battery power port into the small end of the USB charging

cable.

4. Insert the other end of the USB charging cable into a USB port. The

charging indicator will now turn on.

5. Once the charging indicator has turned o, the battery is fully

charged. A full charge will take approx. 75 minutes.

6. Disconnect the USB cable from the USB port.

7. Disconnect the battery power port from the small end of the USB

charging cable.

8. Reconnect the battery wire to the power port on the Voyager

Quadcopter.

9. Close the battery cover. To ensure it is securely closed, push cover in

until it snap-locks into place

Note: Always charge in a dry and ventilated area.
Always remove the battery from the quadcopter when charging.
Do not charge the battery if the surface is still warm.
Only use the original USB charging cable provided.
Replace the battery if it becomes swollen.

1

2

3

4

11

After Sales Support

1300 663 907

Model Number IT315007

[e-mail]

Installation

2.3 Installing Landing Skids and Blade Guards

1. Insert the blade guards onto each of the wings as shown (g 2.3.1).

2. Secure the blade guards with screws.

2.4 Safe Flight Environment

Always check that you are following the rules and regulations for your location.

2.5 Pairing the Voyager Quadcopter with the Remote

1. Push the ON/OFF switch on the remote control to ON.

2. Open the Voyager Quadcopter battery cover and insert the battery connector to the power port.

3. Close the battery cover and turn on the Voyager Quadcopter. The Voyager Quadcopter LED’s will

commence ashing to indicate that it is attempting to pair to the control.

4. Ensure the Voyager Quadcopter is placed on a level surface.

5. Push the left control stick to the highest position until you hear the remote control beep, then pull

down to the lowest position until you hear another beep. When successfully paired, the lights on

the quadcopter will stop ashing and change to solid colours.

g 2.3.1

12

After Sales Support

1300 663 907

Model Number IT315007

[e-mail]

Operation

3.1 Flying the Voyager Quadcopter

NOTE: The best way to know which direction the Voyager Quadcopter is facing is by the coloured LEDs on
its wings. The red lights are on the front two wings, the green lights are on the back wings. Always keep the
Quadcopter in direct line of sight.

Hover up and down:

Push the left control stick up or down. The Voyager

Quadcopter will y upward or downward.

Forward and backward:

Push the right control stick up or down. The Voyager

Quadcopter will y forward or backward.

Turn Left and Right:

Pull the left control stick left or right. The Voyager Quadcopter will

turn left or right.

Sideward y:

Pull the right control stick left or right. The Voyager Quadcopter will

y left or right.

13

After Sales Support

1300 663 907

Model Number IT315007

[e-mail]

3.2 Fine Tuning

The Voyager Quadcopter should keep steady when using the left control stick only. At times however,

you may need to ne tune the control to keep the Voyager Quadcopter steady. Depending on the

issue, use the following buttons to ne tune the Voyager Quadcopter;

Flying forward/backwards:

Use the forward/back switch.

Flying left/right:

Use the mode switch.

Rotating left/right:

Use the left tuning switch.

Note: The amount of ne tuning is indicated on the remote control LCD display.

3.3 Using the Camera

1. Ensure a Micro SD card is securely inserted into the camera.

Note: The gold contacts should be facing down

2. Ensure the camera is connected to the Voyager Quadcopter

correctly, and that the green light indicator is on prior to ying.

3. Taking a Photo:

a. Press the Photo/Video switch on the remote control upwards to take a photo. The camera

LED will ash red to indicate that a photo has been taken.

4. Taking a Video:

a. Press the Photo/Video switch on the remote control downwards to start taking a video. The

camera LED will change to RED to indicate a video is being recorded.

b. Press the Photo/Video switch on the remote control downwards again to stop taking a

video. The Camera LED will change back to GREEN.

Operation

14

After Sales Support

1300 663 907

Model Number IT315007

[e-mail]

3.4 Speed Control

This Voyager Quadcopter can be operated at low speed and high speed settings. These are indicated

by the ‘L’ and ‘H’ on the top right corner of the LCD display.

To change between low and high speed, press the ‘High/Low speed button’ on the top left corner of

the remote control.

3.5 Tricks

Once you are familiar with basic ight operations, you can

perform some impressive tricks.

1. Fly the Voyager Quadcopter to a height of more than 3

metres.

2. Hold down the Trick button on the top right side of the

remote control.

3. While still holding down the Trick button, push the right

control stick in any direction to perform a 360 degree ip.

3.6 Mid Air Start

Thanks to the 6-axis gyroscope, you can throw the Voyager Quadcopter and push the throttle

upwards. The Voyager Quadcopter will automatically level out and hover smoothly in the sky.

3.7 Changing to Mode 2

This Voyager Quadcopter allows you to swap the sideward control with

turn left/right control.

1. With the remote control turned o, hold the Mode Switch to the

right.

2. Turn on the remote control. A longer beep sound indicates the

mode has been changed. You will also notice that Mode 2 is now shown on the LCD display.

Note: To return to Mode 1, perform these steps again.

Operation

15

After Sales Support

1300 663 907

Model Number IT315007

[e-mail]

3.8 Mode 2: Flying

Hover up and down:

Push the left control stick up or down. The Voyager Quadcopter will y

upward or downward.

Forward and backward:

Push the right control stick up or down. The Voyager Quadcopter will y

forward or backward.

Turn Left and Right:

Pull the right control stick left or right. The Voyager Quadcopter will

turn left or right.

Sideward y:

Pull the left control stick left or right. The Voyager Quadcopter will y

left or right.

3.9 Mode 2: Fine Tuning

Depending on the issue, use the following buttons to ne tune the Voyager Quadcopter;

Flying forward/backwards:

Use the forward/backward switch.

Flying left/right:

Use the left tuning switch.

Rotating left/right:

Use the mode switch.

Operation

16

After Sales Support

1300 663 907

Model Number IT315007

[e-mail]

3.10 Resetting the Voyager Quadcopter

In the event of the Voyager Quadcopter ying in a strange manner, rst check that there is no issue

with ne tuning on the remote control.

If ne tuning did not solve the issue, you can reset the Voyager Quadcopter to factory settings

with this method:

1. Perform the steps in “Pairing the Quadcopter with the

Remote Control” to pair with the Voyager Quadcopter.

2. Hold both control levers at their bottom right position. The

Voyager Quadcopter LED’s will ash rapidly.

3. After 2-3 seconds, the LEDs will stop ashing and

change to a solid colour. This indicates that the Voyager Quadcopter has restarted and reset

successfully.

3.11 Replacing Propellor Blades

Eventually your propeller blades may need to be replaced. Do not operate the Voyager

Quadcopter with damaged propeller blades as you may suddenly lose control of the Quadcopter

during ight. Follow the steps below to replace your Voyager Quadcopter’s propeller blades.

1. Position the Voyager Quadcopter on a level, horizontal surface with the front end facing

forward, as shown below.

2. Determine which blades need replacing and note the blade type (A or B) by checking the

underside of the blade.

3. Using the screwdriver provided, unscrew the damaged blade.

4. Replace the blade with the same type (A or B), also checking the diagram below to conrm the

correct blade type.

5. Screw in the replacement blade rmly using the screw that was removed in step 3.

6. When ying your Voyager Quadcopter again, gently increase the throttle to check that the

Voyager Quadcopter will remain stable when ying. If the incorrect blade type is used, the

Voyager Quadcopter will be unable to remain level.

Operation

Front BA

AB

17

After Sales Support

1300 663 907

Model Number IT315007

[e-mail]

FAQs

Question Solution

My Voyager Quadcopter didn’t pair with my
Remote Control

At times the Voyager Quadcopter may fail to pair with
the remote control. Attempt to pair again, ensuring the
Voyager Quadcopter is resting on a level surface.

My Voyager Quadcopter isn’t responding Check that the battery in the Voyager Quadcopter

is still charged. Also check that the remote control
batteries are still charged.

My Voyager Quadcopter is slow to respond Ensure that the remote control batteries are still

charged. There may also be interference from a similar
frequency nearby. Try using the Voyager Quadcopter in
a dierent location, away from other radio controlled
devices.

Not ying straight or spinning Follow the steps in ‘Fine Tuning’ to congure the

Voyager Quadcopter correctly. If unsuccessful, also
try following the steps in ‘Resetting the Voyager
Quadcopter’.

My video wasn’t saved To save power, the Voyager Quadcopter only saves

videos when you press the video button to stop
recording. Unfortunately, if the Quadcopter runs out
of power whilst recording, the video won’t be saved.
Recharge the Voyager Quadcopter and try taking a
video again, making note of how much battery may be
remaining.

Repair and Refurbished Goods

or Parts Notice

Unfortunately, from time to time, faulty products are manufactured which need to be returned
to the Supplier for repair.

Please be aware that if your product is capable of retaining user-generated data (such as files
stored on a computer hard drive, telephone numbers stored on a mobile telephone, songs
stored on a portable media player, games saved on a games console or files stored on a USB
memory stick) during the process of repair, some or all of your stored data may be lost.

We recommend you save this data elsewhere prior to sending the product for repair.

You should also be aware that rather than repairing goods, we may replace them with
refurbished goods of the same type or use refu

rbished parts in the repair process.

Please be assured though, refurbished parts or replacements are only used where they
meet ALDI’s stringent quality specifications.

If at any time you feel your repair is being handled unsatisfactorily, you may escalate your
complaint. Please telephone us on 1300 663 907 or write to us at:

Winplus Australasia
PO BOX 537

Bayswater Business Centre
Bayswater, VIC 3153

Winplus Help Desk 1300 663 907
(Operating Hours: Mon-Fri 08:30AM to 6:00PM)

[e-mail]
www.winplus.com.au

AFTER SALES SUPPORT

YEAR WARRANTY

1

MODEL: IT315007 PRODUCT CODE: 51176 09/2015

[e-mail]

1300 663 907

AUS

VOYAGER QUADCOPTER

Flight Log

Date Time Location Event Log