Cocoon HE161192 Instruction Manual

.

.

MODEL NUMBER: HE161192

INSTRUCTION MANUAL

VERSION 1
ISSUED 23/11/17

.

.

.

.

.

.

WARRANTY NOTE

If you experience any issues with this product or its
performance is not what you had expected, please contact
us at Winplus before returning the item to the store.

It is likely that we can resolve any problems for you via
phone or email.

We can be reached on:

Phone: [phone] (Mon - Fri; 8:30am - 6:00pm AEST)
Email: [e-mail]
Web: www.winplus.com.au

IMPORTANT

Getting the most out of your 3D Printer Touch:

Read the manual carefully

It will help you set up with ease

Visit www.cocoonproducts.com.au

We have additional support videos and guides

Call After Sales Support - 1300 663 907

Available Monday - Friday, 8:30am - 6:00pm AEST

Email [e-mail]

We’re always happy to help

.

.

.

Warranty Details

The product is guaranteed to be free from defects in workmanship and parts for a period
of 12 months (dependant on product) from the date of purchase. Defects that occur within this
warranty period, under normal use and care, will be repaired, replaced or refunded
at our discretion. The benets conferred by this warranty are in addition to all rights and
remedies in respect of the product that the consumer has under the Competition and
Consumer Act 2010 and similar state and territory laws.

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law.
You are entitled to a replacement or refund for a major failure and for compensation
for any other reasonably foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the failure
does not amount to a major failure.

AFTER SALES SUPPORT

MODEL: HE161192 PRODUCT CODE: 56826 01/2018

REGISTER YOUR PURCHASE ATwww.aldi.com.au/en/about-aldi/product-registration/TO KEEP UP-TO-DATE WITH IMPORTANT PRODUCT INFORMATION

1300 663 907

AUS

[e-mail]

YEAR WARRANTY

1

3D Printer Touch

create

.

5

.

AFTER SALES SUPPORT

1300 663 907 [e-mail] MODEL: HE161192

SAFETY INSTRUCTIONS

Before you get started, please read these important safety instructions.

CAUTION: The Cocoon Create 3D Printer Touch generates high temperatures and includes moving

parts that can cause injury. Never reach inside of the Cocoon Create 3D Printer Touch while it is in

operation, and allow time for the printer to cool down after operation.

Vapours/fumes may be irritating at operating temperatures. Always use the Cocoon Create 3D
Printer Touch in an open, well ventilated area.

Do not leave the Cocoon Create 3D Printer Touch unattended during operation

Contact with extruded material may cause burns. Wait for printed objects to cool before
removing them from the build platform.

Always take care when using the Scraper. Never direct the Scraper towards your ngers.

Only use the 3D Printer Touch in a clear working area

• The printer must not be exposed to water or rain, or damage will occur.

• The printer is designed to be used with ambient temperature ranging 15°C - 30°C, and humidity
ranging 20% - 50%. Operating outside these limits may result in low quality models.

• In case of emergency, turn o the 3D Printer Touch at the power outlet.

• It is recommended that you use eye protection when cleaning/sanding printed models to avoid small
particles contacting eyes.

• Please read and understand the contents of this installation and user manual carefully. Failure to read
the manual may lead to personal injury, inferior results, or damage to the 3D Printer Touch. Always
make sure that anyone who uses the 3D printer knows and understand the contents of the manual
and makes the most out of the 3D Printer Touch.

• 3D Printer Touch is not intended for use by persons with reduced physical and/or mental capabilities,
or lack of experience and knowledge, unless they have been given supervision or instruction
concerning the use of the appliance by a person responsible for their safety. Children should be under
constant supervision when using the printer.

• Before installation, you should make sure that the 3D Printer Touch is unplugged from the power
supply. Only using furniture that can safely support 3D Printer Touch.

• The socket-outlet shall be installed near the equipment and shall be easily accessible.

3D Printer Touch has been tested according to the AS/NZS 60950-1, which falls under the low voltage
directive. 3D Printer Touch must be used in conjunction with the original power cord. In combination,
they guarantee safe use in relation to short-circuit, overload, over-voltage and over temperature. Always
unplug the printer before doing maintenance or modications.

HOT SURFACE

MOVING PARTS

DO NOT TOUCH

.

6

.

CONTENTS

Warranty Details 4

Safety Instructions 5

Parts List 8

Technical Specications 9

Introduction 10

1.1 What is 3D Printing? 10

1.2 From 3D Design to Printed 3D Object 10

1.3 Good 3D Printing Practices 12

Product Overview 13

2.1 Printer Front View 13

2.2 Printer Rear View 14

2.3 Print Bed 15

2.4 Control Panel 16

2.5 Touch Screen Control Panel 17

Setup 20

3.1 Unboxing and Assembly 20

3.2 Levelling the Bed 22

3.3 Filament 24

3.3.1 Filament Types 24

3.3.2 Inserting Filament 25

3.3.3 Removing Filament 25

3.3.4 Storage 25

3.4 Using the SD Card 26

3.4.1 Loading les from your Computer 26

3.4.2 Printing from the SD Card 26

3.5. Removing 3D Objects from the Bed 27

Preparing To Print a File 28

4.1 Creating a GCODE File 28

4.2 Cura Setup 28

4.3 Download the Latest Cura Prole 28

.

7

.

AFTER SALES SUPPORT

1300 663 907 [e-mail] MODEL: HE161192

Servicing 29

5.1 Servicing your 3D Printer Touch 29

5.1.1 Replacing the Print Mat 29

5.1.2 Nozzle Cleaning 29

5.1.3 Extruder Cleaning 30

5.1.4 Routine Component Check 30

5.1.5 Storing 30

Finishing 31

6.1 Finishing Techniques 31

6.1.1 Useful Tools/Equipment 31

6.1.2 Removing Support Material 31

6.1.3 Sanding 32

6.1.4 Surface Coating 32

Maintenance 33

Disposal of Packaging 33

Disposal of Product 33

Troubleshooting 34

10.1 Troubleshooting 34

10.1.1 Printing Problems 34

10.1.2 Connectivity Problems 35

10.1.3 Other Problems 36

10.2 Useful Terms 36

Appendix 38

References 38

Repair and Refurbished Goods or Parts Notice 39

.

8

.

PARTS LIST

1 x Cocoon Create 3D Printer

Touch (Extruder Tower,

Heated Print Bed)

1 x Filament Spool Holder

1 x Filament Spool Stand

1 x Power Cable

1 x USB Cable

1 x SD Card

1 x Scraper

1 x Replacement PTFE Tube

1 x Hex Key Set

6 x Hex Bolts

2 x Cable Ties

4 x 10m PLA Filament

3 x Print Bed Mats

(1 on Print Bed and 2 spare)

1 x 0.4mm Drill Bit

1 x Extruder Cleaner

6 x Rubber Feet

1 x Levelling Card

1 x Instruction Manual

1 x Getting Started Guide

1 x Warranty Card

.

9

.

AFTER SALES SUPPORT

1300 663 907 [e-mail] MODEL: HE161192

TECHNICAL SPECIFICATIONS

Printing

Print Technology: Fused Filament Fabrication (FFF)

Build Volume: 200 x 200 x 180mm

Layer Resolution: 0.1 – 0.4mm

Positioning Accuracy: X 0.012mm

Y 0.012mm

Z 0.004mm

Extruder Quantity: Single Extruder

Extruder Diameter: 0.4mm

Print Speed: 10mm/s - 70mm/s

Travel Speed: 10mm/s - 70mm/s

Supported Print Materials: Cocoon Create Branded PLA, ABS, PVA,

HIPS, PLA Wood, PLA Flex, Conductive

Temperature

Ambient Operating Temperature: 15°C – 30°C

Operational Extruder Temperature: 170ºC – 255ºC

Operational Print Bed Temperature: 15ºC – 109ºC

Software

Slicer Software: Cura

Cura Input Formats: .STL, .OBJ, .DAE, .AMF

Cura Output Format: .GCODE

Connectivity: SD Card, USB port (Expert users only)

Electrical

Input Rating: 200-240VAC, 50/60Hz, 2.0A

Physical Dimensions

Printer Frame Dimensions: 400 x 410 x 400mm

Weight: 10KG

.

10

.

1.1 What is 3D Printing?

3D Printing is a process whereby a real object is created from a 3D Design. Fused Filament

Fabrication (FFF) is one of the most common technologies used by 3D Printers to achieve this. FFF

works on an ‘additive’ principle by laying down material, such as PLA or ABS lament, in layers to

create a 3D object.

1.2 From 3D Design to Printed 3D Object

3D Design Slice to GCODE Setup 3D Printer Touch 3D Printing Process 3D Printed

Object

3D Design

Having a 3D Design is the rst step to creating a 3D Object. To start your

creative journey, visit www.cocoonproducts.com.au/3dcreator to download

and share free 3D Designs. There are a number of websites that provide free

access to 3D designs however all that we provide are already converted

to the correct printing format (GCODE). Most other website les require

reformatting (See ‘Slice to GCODE’ for further information).

Alternatively, you can create your own 3D Design using 3D Modelling Software. Programs such as

SketchUp or Blender allow this, however this can take some practice before successfully modelling

your 3D Design. After you’ve nished your 3D Design, you can export it as an .STL le, to be

imported into a ‘Slicer’ program such as Cura.

Slice to GCODE

A ‘Slicer’ converts a 3D Design (usually in .STL or .AMF format) into

individual layers. It then generates the machine code (such as GCODE) that

the 3D Printer Touch will use for printing.

INTRODUCTION

.

11

.

AFTER SALES SUPPORT

1300 663 907 [e-mail] MODEL: HE161192

We recommend Cura, as it uses a simple interface and includes a large

amount of support material.

Setup 3D Printer Touch

It’s important to set up your printer before every print. We’ve included some

steps on page 12 in section 1.3 ‘Good 3D Printing Practices’ for you to

quickly refer to each time.

3D Printing Process

Now that you’ve loaded a GCODE le onto the printer, it will commence

heating up the Extruder and Heated Print Bed, then start printing. While

printing, the nozzle will move along the X and Y axis as each layer is printed.

This can take some time, depending on the size of the 3D model, print speed of the 3D Printer Touch

and resolution of each layer.

Here is an example of how size, inll, and resolution can aect printing time:

Dimensions:

62.5 x 25.75 x 67.75mm 70 x 70 x 140mm

Inll:

20% 0% 20% 20%

Resolution:

2mm 2mm 2mm 1mm

Print Time:

53min 39min 6hr 40min 13hr 12min

Filament Used:

4m 2.54m 45m 45.67m

3D Printed Object

Once the printer has completed all the layers, you will have a 3D Printed Model.

The Cocoon Create 3D Printer Touch is compatible with a broad range of lament types and is

capable of printing 3D models ranging from small and simple to complex objects with moving parts.

What you print is limited only by your imagination.

INTRODUCTION

.

12

.

1.3 Good 3D Printing Practices

Please refer to these steps during every print to ensure the best quality.

Before Printing

1. Ensure your GCODE le is correctly setup, lament diameter is set to 1.75mm and correct

temperature settings for the material you are using (refer to table 3.3.1, page 24)

2. Check all cables and connectors are connected

3. Check that Heated Print Bed is level and approximately 0.1mm from the nozzle

4. Check that Heated Print Bed is clean and dust free and nozzle does not have excess material

stuck to it

During Printing

1. Closely monitor the rst layer being printed – Most problems will occur in the rst layer. If

problems occur, stop the 3D Printer Touch at the power outlet

2. Do not leave the 3D Printer Touch unattended while in operation

3. Keep hands clear while machine is operating

After Printing

1. Wait for the Heated Print Bed and Extruder to cool down

2. Carefully remove 3D Object using the supplied scraper. Never use Scraper towards your body.

Keep Scraper evenly at when scraping to avoid damage to the Heated Print Bed. Damaged

Heated Print Bed will aect adhesion for future prints

3. Store 3D Printer Touch in a clean, dry environment

INTRODUCTION

Always check Print Mat
is clean and there is no

residual plastic

Always check all cords

are connected

Always check GCODE

file settings match

filament and printer

Always check Extruder

distance is 0.1mm

from Print Mat

Always check Print

Bed is level

.

13

.

AFTER SALES SUPPORT

1300 663 907 [e-mail] MODEL: HE161192

PRODUCT OVERVIEW

2.1 Printer Front View

1. X Rail

2. X Belt Drive

3. Extruder Spring Lever

4. Extruder Cooling Fan

5. X Stop (Micro Switch)

6. Filament Cooling Fan

7. Extruder Driving Motor

8. Filament Spool Holder

Assembly

9. Tower Frame

10. Touch Screen

6

2

9

10

8

1

4

7

3

5

.

14

.

PRODUCT OVERVIEW

2.2 Printer Rear View

1. X Cable Track

2. X Axis Stepper Motor

3. Z Cable Track

4. Extruder

5. Z Drive Screw

6. Z Rod

7. Z Stop (Micro Switch)

8. Z Axis Stepper Motor

3

4

8

5

6

1 2

7

.

15

.

AFTER SALES SUPPORT

1300 663 907 [e-mail] MODEL: HE161192

PRODUCT OVERVIEW

2.3 Print Bed

1. Y Stop (Micro Switch)

2. Heated Print Bed

3. Printing Mat

4. Levelling Thumb Screw

5. Print Bed Frame

6. Y Axis Stepper Motor

7. Y Belt Drive

8. Y Rail

2

1

3

4

5

8

7

6

.

16

.

PRODUCT OVERVIEW

2.4 Control Panel

1. Touch Screen

2. SD Port

3. Mini USB Port

4. Power Socket

5. Power Switch

1

2

3

4

5

.

17

.

AFTER SALES SUPPORT

1300 663 907 [e-mail] MODEL: HE161192

2.5 Touch Screen Control Panel

Print

• Choose File: Shows les on SD card ready to print

• Status: Status of chosen print le

• Bed Temperature: (0-109ºC)

• Extruder Temperature: (0-255ºC)

• Fan Speed: (0-100%)

• Continue: Starts/resumes printing the selected le

• Pause: Pauses the currently printing le

• Settings: manually increase/decrease print speed (0-300%), extruder temperature, bed

temperature and fan speed

NOTE: If you are making changes in ‘Settings’, ensure you select ‘Conrm’ to proceed to update the
changes made for your current print le

• Stop: Stops the current print job completely

• Back: Return to Main Menu

PRODUCT OVERVIEW

.

18

.

PRODUCT OVERVIEW

Quick Menu

• Preheat: Preheat Extruder and Heat Bed Temperature for PLA or ABS lament

• Home XZY: Automatically resets Extruder location to Home position

• Move:

• -X Axis+: Move the Extruder along the X-Axis manually

• -Z Axis+: Move the Extruder along the Z-Axis manually

• -Y Axis+: Move the Extruder along the Y-Axis manually

• Extruder Flow:

• In: Pulls lament into the Extruder

• Out: Ejects the lament out of the Extruder

• Disable Motor: Unlocks Print Bed to be movable manually

• Home X: Position the Extruder to the home position on the X-Axis

• Home Y: Position the Extruder to the home position on the Y-Axis

• Home Z: Position the Extruder to the home position on the Z-Axis

• Back: Return to Quick Menu

• Cool Down: Select to begin cooling down your Printer’s Print Bed and Extruder

• Change Filament:

• Add Filament: Select from Touch Screen the type of lament you will be inserting.

• Remove Filament: Select from Touch Screen the type of lament you will be removing.

Your Printer will begin to heat up the Extruder and Print Bed to the correct temperature

settings of selected lament type

• Raise Extruder: Automatically raise the Extruder from the Print Bed

• Preheat PLA: Select for printing with PLA Filament. Once selected, the Bed Temperature

and Extruder Temperature status will be displayed on touch screen

• Preheat ABS: Select for printing with ABS Filament. Once selected, the Bed Temperature

and Extruder Temperature status will be displayed on touch screen

• Back: Return to Change Filament Page

• Disable Motor: Unlocks Print Bed to be movable manually on x and y-axis only

• Back: Return to Main Menu

.

19

.

AFTER SALES SUPPORT

1300 663 907 [e-mail] MODEL: HE161192

PRODUCT OVERVIEW

Level Wizard

Follow instructions on the touch screen for levelling the Print Bed

• Back: Return to Main Menu

Advanced Settings

• PID Settings: (We recommend to leave setting as default if you are new to 3D Printing)

• PID-P: Proportial Response

• PID-I: Integral Response

• PID-D: Derivative Response

• Conrm: Select to update print settings

• Back: Return to Advance Settings

• Motor Settings:

• X-Axis:

• Y-Axis:

• Z-Axis:

• E-Axis:

• Conrm: Select to update print settings

• Back: Return to Advance Settings

• Factory Reset: Resets 3D Printer to default Settings

• Back: Return to Main Menu

.

20

.

3.1 Unboxing and Assembly

Your Cocoon Create 3D Printer Touch is packed tightly and carefully - take your time unpacking it.

To view a step by step video of the Unboxing and Assembly, visit cocoonproducts.com.au

1. Carefully remove the Extruder Tower and Heated Print Bed from the

box and place them on a clean, level work space. Slot the rubber feet

onto all 4 corners of the Heated Print Bed Base, and one on both sides

of the Extruder Tower Base. Carefully remove the cable tie that holds

the Extruder in place

NOTE: Raise the Extruder by gently pulling the z-axis rod towards the top of the
Extruder Tower and move the Extruder to one side prior to assembling the Printer

2. Insert the Heated Print Bed Controller carefully through the legs of the

Extruder Tower and align the bolt holes on each side. Using the Hex

Wrench, insert and tighten the two bolts on bottom of each Extruder

Tower

3. Insert the long cable connector marked ‘A’ into the motor connector of

the Extruder Tower marked ‘A’

4. Insert the short cable connector marked ‘B’ into the motor connector

of the Extruder Tower marked ‘B’

5. Insert the white connector marked ‘C’ into the motor connector of the

Extruder Tower marked ‘C’

SETUP

.

21

.

AFTER SALES SUPPORT

1300 663 907 [e-mail] MODEL: HE161192

6. Insert the black connector marked ‘D’ into the black connector of the

Extruder Tower marked ‘D’

7. Insert one end of the black cable connector marked ‘E’ into the black

connector of the Extruder Tower marked ‘E’. Insert the other end to the

black connector marked ‘E’ into the black connector on the side of the

Heated Print Bed marked ‘E’

8. Attach the upper arm of the lament spool holder by unscrewing the

end cap, then reattaching. Position the Filament Spool Holder Stand on

top of the Extruder Tower, then insert the bolts and tighten with the Hex

Wrench

9. Ensure the power switch is in the OFF position, then insert the Power

Supply Cable into the back of the 3D Printer Base. Insert the other end

into a nearby mains power outlet. Turn on the power outlet, then turn on

the power switch at the back of the 3D Printer Base

10. Wait for the printer to initialise, with the home screen shown on the

Touch Screen.

You have successfully setup your Cocoon 3D Printer Touch

SETUP

.

22

.

SETUP

3.2 Levelling the Bed

IMPORTANT NOTE: Levelling the bed is an extremely important step and if it is not done
correctly every time, your prints will fail or be of poor quality

Before you begin to level the Heated Print Bed:

• Ensure the springs on all 4 corners of the Heated Print Bed are tightened all the way to the

bottom by turning each thumbwheel anti-clockwise until you can no longer turn them. This

reduces the distance between the 2 plates of the print bed to a minimum. Wipe the top of the

Heated Print Bed with a clean, lint-free cloth to ensure no dust particles or other objects are on

the Heated Print Bed

• Check the Z axis alignment. The X rail (holding the Extruder) should be parallel to the Heated

Print Bed. If it is not, manually rotate individual z-axis stepper motors

on the bottom of both shafts to adjust. Place a Hex Wrench on the

z-axis rod and run it across the Heated Print Bed to check the z-axis is

aligned horizontally

Option 1 – Using Level Wizard to Level the Bed

1. Press ‘Level Wizard’ on the touch screen panel and follow the steps

as indicated

NOTE: The ‘Level Wizard’ will guild you through levelling each corner of your Print Bed. Check
the Heated Print Bed is approximately 0.1mm from the nozzle. Once all 4 corners are checked, it is
recommended that you press ‘Next’ to thoroughly check once more and ensure your Bed is levelled.

2. To return to Main Screen, press ‘Back’

Nozzle Too High

Insucient contact area

resulting in poor adhesion

and extrusion skipping

Correct Height

Filament pushed into the

print bed slightly to maximize

surface area contact whilst

still allowing good extrusion

ow

Nozzle Too Low

Not enough clearance for

the lament to be extruded,

which can damage the

extruder and/or print bed

.

23

.

AFTER SALES SUPPORT

1300 663 907 [e-mail] MODEL: HE161192

SETUP

Option 2 – Manually Levelling the Bed

1. Select ‘Quick Menu’ on the Main Screen and select ‘Home XYZ’

NOTE: The 3D printer extruder nozzle will move to the ‘Home’ position in the front left corner of the
Heated Print Bed. Turn o the 3D printer.

NOTE: Immediately turn o the machine if any of the motors are jamming or forcing against the
chassis

2. Select Disable motor to manually move the Bed

3. Manually move the Bed so the Nozzle Head is at a corner of the Bed

4. Adjust the thumbwheels on the bottom of the Heated Print Bed so the distance between the

Bed and the Nozzle head is approximately 0.1mm apart

5. Fine tune the gap distance by sliding the levelling card or using an A4 piece of paper. You

should be able to feel a slight friction when sliding the paper between the Bed and the

Nozzle Head

6. Repeat steps 4 to 6 for all other corners of the Bed

7. Move the Extruder to the centre of the Heated Print Bed and test the gap with the levelling

card or a sheet of paper. Keep adjusting and testing until the gap is uniform on all points of

the bed

.

24

.

3.3 Filament

The Cocoon Create 3D Printer Touch uses high quality PLA and ABS laments. Only use quality

Cocoon Create laments as using generic laments may damage your 3D Printer Touch, aect the

print quality and may void your warranty. Extra lament including multiple colours and types are

available from the online store at cocoonproducts.com.au.

For beginners, we recommend using PLA materials as they are easy to print and does not

produce fumes when printing. Before using other types of laments, ensure you understand the

advantages and disadvantages of other laments and their proper usage.

3.3.1 Filament Types

Filament Type PLA ABS PVA HIPS

Extruder Temp: 215ºC 240ºC 175ºC 240ºC

Heat Bed Temp 60ºC 90ºC 50ºC 60ºC

Ocial Name: Polyactic Acid Acrylonitrile

Butadiene Styrene

Polyvinylv Alcohol High Impact

Polystyrene

Printing Level: Basic Advanced Advanced Advanced

Advantages: • Bioplastic

• Non-Toxic

• Less warping
issues

• Hard or soft/
exible variants

• High print
speed

• Smooth nish

• Durable

• Ideal for
mechanical
parts

• Water soluble

• Non-Toxic

• Lightweight

• Cost eective

• Dissolvable in
Limonene

Disadvantages: • Low heat

resistance

• Easier to break
than ABS

• Requires
thicker walls
than ABS

• Petroleum­based

• Non­biodegradable

• Heated Print
Bed required

• Fumes when
printing

• Sunlight
deterioration

• Sensitive to
high heat.

Do not heat
over 190C

• Only available
in white

Finishing: • Sanding

possible

• Limited gluing

• Easy sanding

• Easily soluble in
acetone

• Gluing Only • Gluing Only

Alternative types of PLA

These PLA Alternatives require advanced knowledge of the 3D Printer Touch. Please visit

www.cocoonproducts.com.au for details of lament types and parameters.

SETUP

.

25

.

AFTER SALES SUPPORT

1300 663 907 [e-mail] MODEL: HE161192

SETUP

3.3.2 Inserting Filament

1. On the Main Screen, select ’Quick Menu’ > ‘Change Filament’> ‘Add Filament’

2. Select the desired type of Filament to be added. The Extruder will automatically be raised

and your Printer will begin heating the Extruder to the correct temperature. When the

temperatures are within a few degrees of the target, you are ready to insert the lament

3. Place the included lament onto the Spool holder. Carefully insert the end of the lament into

the hole on the Extruder. The Extruder will begin to slowly pull the lament in. Once lament

begins extruding, press ‘Back’ to stop

4. Carefully remove the extruded lament from the Nozzle Head and ensure the Print Bed is

clean

WARNING: Extruder and Heated Print Bed will still be hot

3.3.3 Removing Filament

1. On the Main Screen, select ’Quick Menu’ > ‘Change

Filament’> ‘Remove Filament’

2. Select the desired type of Filament to be removed. The Extruder will automatically be raised

and your Printer will begin heating the Extruder to the correct temperature

3. Once the Extruder reaches the correct temperature, the lament will begin retracting from

the Extruder. Gently pull the lament up until it is released and press ‘Back’ to stop

NOTE: Trim of the end of the retracted lament prior to reinserting into the Extruder to prevent
clogging the Printer Nozzle.

3.3.4 Storage

Both PLA and ABS laments are sensitive to moisture. If stored in a humid environment, the quality

of the lament can deteriorate, with a tendency to bubble and spurt from the nozzle tip. This will

aect print quality, so when storing PLA or ABS for an extended period of time, follow these tips.

• Store in a sealed, air tight bag/container. We recommend a vacuum seal bag

• Store with a silica gel (moisture absorber) pack. One is included with each lament spool

.

26

.

SETUP

3.4 Using the SD Card

3.4.1 Loading les from your Computer

1. Insert your SD Card into a card reader or memory card slot and connect to your computer

(refer to your computer manual for further instructions if required)

2. The SD Card will appear as a folder (refer to your computer manual for further instructions if

required)

3. Copy your converted GCODE les to the SD card, then safely remove

3.4.2 Printing from the SD Card

1. Insert the included SD card into the slot on the right side of the 3D Printer, ensuring that the

metal contacts are facing upwards

2. Select ‘Print’ from the Main Menu and select your desired le to print

3. Once selected, your le will begin to load and your le status can be viewed on the touch

screen. Your printer will automatically commence heating the Extruder and Print Bed to the

correct printing range before commencing the print

NOTE: If your le is not printing correctly, press the ‘Stop’ Button to discontinue the print. Ensure the
extruder is raised prior to removing the print o the Bed

NOTE: Immediately turn o the machine if any of the motors are
jamming or forcing against the chassis

NOTE: If you cannot access the Print menu, it is likely the SD Card is not
mounted properly. Try removing and reinserting the SD Card.

.

27

.

AFTER SALES SUPPORT

1300 663 907 [e-mail] MODEL: HE161192

SETUP

3.5. Removing 3D Objects from the Bed

When the Cocoon Create 3D Printer Touch has completed printing your 3D printed object, it’s time

to remove the object from the bed.

1. Once the print is completed, the nozzle and Heated Print Bed will automatically commence

cooling down. Wait until the Extruder and Heated Print Bed have cooled down to room

temperature. This will allow the plastic to contract, making it easier to remove

2. Once cooled, turn o your 3D printer and carefully remove the 3D printed object using the

supplied Scraper , carefully ‘wedge’ under one of the edges of the 3D object. Take care to keep

the Scraper at with the bed, as to not cause damage to the Print Mat

3. As one edge begins to lift, gently maneuver the Scraper forward to continue to ‘wedge’

between the 3D object and the Heated Print Bed

4. Once the part has fully separated from the bed, it is safe to remove

NOTE: Always take care when using the Scraper. Never use excessive force or scrape towards your hand.

NOTE: Always keep the Scraper as level as possible. Scraper can damage the print mat if not used

correctly

NOTE: Removing a 3D object, particularly one with a large surface size, can be a long process. Never
rush when removing a 3D printed object

TIP: If you are persistently having trouble removing 3D printed objects, try the following:

• Use a layer of blue masking tape (designed to not leave behind residue) on the Heated Print

Bed. Be sure to remove and replace after each print

• Check if the printing mat is damaged and replace if needed

Replacement mats can be purchased at cocoonproducts.com.au

.

28

.

PREPARING TO PRINT A FILE

4.1 Creating a GCODE File

The Cocoon Create 3D Printer Touch prints 3D les in GCODE format. GCODE les provide essential

movement and printer settings required to print your object. To prepare and convert your 3D le

to GCODE format, you must use a ‘Slicer’ program such as Cura. Cura is a free open source slicer

available for Windows and Mac platforms. Cura can convert various 3D le formats, such as STL

les, into GCODE. Follow the steps below to download and install Cura.

4.2 Cura Setup

Install the Cura software on the included SD card or download the latest version of Cura from the

link below:

https://ultimaker.com/en/products/cura-software/list

You can learn how to install and use Cura from below link:

https://ultimaker.com/en/resources/16579-installation

After installing Cura, please add your Cocoon Create 3D

Printer Touch to Cura:

1. On rst launch, Cura will ask you to add a 3D Printer

Touch. Alternatively, you can add a 3D Printer Touch

by selecting Machine > Machine Settings > Add

New Machine

2. Select Other

3. Select Custom…

4. Enter Machine name as ‘Cocoon Create Touch’, or your desired name

5. Input Machine width and depth as 200

6. Input Machine height as 180

7. Change Nozzle size to 0.4mm

8. Ensure Heated Print Bed is ticked

9. Select ‘Finish’

4.3 Download the Latest Cura Prole

For optimal print settings, download the most up to date Cocoon Create 3D Printer Touch Cura

Prole from the link below and import it into Cura. Note this is optimized for use with PLA.

https://www.cocoonproducts.com.au/download/

.

29

.

AFTER SALES SUPPORT

1300 663 907 [e-mail] MODEL: HE161192

SERVICING

5.1 Servicing your 3D Printer Touch

5.1.1 Replacing the Print Mat

The Cocoon Create 3D Printer Touch includes 2 Extra Print Mats.

Additional Print Mats are available for purchase from

cocoonproducts.com.au

1. Remove the current Print Mat by slowly peeling from one corner

2. Using rubbing alcohol and a microber towel, carefully remove any

residual adhesive left on the Heated Print Bed

3. Peel the 3M backing from the new Print Mat

4. Gently place the new Print Mat onto the Heated Print Bed, making

sure to align with each edge. It is recommended to start at a corner

to ensure no bubbles become present

5. Use the Scraper to apply pressure on the new Print Mat, ensuring

strong adhesion. Keep the Scraper level as it can damage the Print

Mat

TIP: Warming the bed slightly may make removal easier. You can also use masking tape in lieu of a

Print Mat. Blue painters tape is recommended.

5.1.2 Nozzle Cleaning

If your Extruder nozzle becomes blocked, follow these steps to clean the

nozzle.

1. Remove the existing lament using steps from section 3.3.3

‘Removing Filament’

2. Using a clean 0.4mm drill bit, insert the drill bit into the nozzle by

hand, twisting while inserting

3. Remove the drill bit from the nozzle, twisting while removing

4. Repeat steps ‘2’ and ‘3’ three times, then follow the steps in section

3.3.2 ‘Inserting Filament’ to re-insert the lament into the nozzle

1

2

3

4

.

30

.

5.1.3 Extruder Cleaning

If your Extruder becomes blocked, follow these steps to unclog the Extruder.

1. Remove the existing lament using steps from section 3.3.3 ‘Removing Filament’

2. Gently press down on the Extruder lever, and carefully insert the Extruder Cleaner into the

lament hole. You will notice excess lament clogged in the Extruder being pushed through

the nozzle.

3. Remove the Extruder Cleaner from the hole and repeat the step ‘2’ until no more lament is

exiting the nozzle.

4. Follow the steps in section 3.3.2 ‘Inserting Filament’ to re-insert the lament into the nozzle

5.1.4 Routine Component Check

Motor Connectors

Loose motor connections could cause a 3D print to fail. It’s a good habit to

routinely check for any damage to the connectors or the black cables.

Axis Lubrication

Regular lubrication of the X and Y Axis rods is important for the longevity

and smooth running of your printer. The rods can be lubricated with

machine oil or synthetic grease. We recommend using bearing grease, and

to apply generously to both the X Axis and Y Axis rods.

Nuts and Bolts

Loose nuts and bolts could aect the geometry of the 3D Printer Touch.

Check that all nuts and bolts remain rmly tightened. If required, re-tighten using the hex wrench.

5.1.5 Storing

Always store your 3D Printer Touch in a cool, dry location that is free from dust.

SERVICING

.

31

.

AFTER SALES SUPPORT

1300 663 907 [e-mail] MODEL: HE161192

FINISHING

6.1 Finishing Techniques

6.1.1 Useful Tools/Equipment

• Safety Goggles

• Mask

• Long-nose Pliers

• Wire cutters

• Sandpaper (100, 200, 300, 400, 500, 600 Grit)

• Medium, ne and extra ne sanding sponges

• Acrylic based primer spray paint

• Acrylic based spray paint (colour of your choice)

• Acrylic based varnish spray paint

NOTE: Dierent paint types are also compatible with PLA and ABS. Consult your local paint supplier for
the best compatibility for your intended purpose.

6.1.2 Removing Support Material

Even after support material is removed by hand, residual material will remain.

1. Ensure that safety goggles and a mask are worn for protection

2. Remove most of the support material by hand, taking care not to

damage the 3D object

3. Using the long-nose pliers, carefully grasp some of the remaining

material, then twist to remove. Repeat until no more material can

be removed.

4. Using the wire cutters, cut away any excess lament.

3

.

32

.

6.1.3 Sanding

Though Fused Filament Fabrication (FFF) is capable of producing high quality objects straight out

of the machine, the layer lines will be visible. Sanding will reduce these ‘step’ marks in the model.

1. Ensure that safety goggles and a mask are worn for protection

2. Starting with 100 grit sandpaper, carefully sand your 3D object using small, circular motions

NOTE: PLA is less resistant to high temperatures caused by sanding. Take your time sanding your 3D
object to avoid damage.

3. Using the medium sanding sponge, sand dicult to reach areas of your 3D object

4. Gradually increase the sandpaper grid until the 3D print is smooth

TIP: Spraying a primer ller will also help to reduce the layer lines on the 3D Object. This can then be
sanded away and repeated, until the desired smoothness is achieved

6.1.4 Surface Coating

Finally, to make your models more presentable, follow these steps;

1. Ensure that safety goggles and a mask are worn for protection

2. Ensure that your 3D object is clean and free from dust

3. Spray your model using an acrylic based primer, following the directions of your primer

4. Allow appropriate time to dry before applying additional coats

5. Spray your model using an acrylic based paint of your colour. Allow appropriate time to dry

6. Spray your model using an acrylic based varnish, following the directions of your varnish.

Allow appropriate time to dry before applying additional coats.

NOTE: Dierent paint types are also compatible with PLA and ABS. Consult your local paint supplier for
the best compatibility for your intended purpose.

Congratulations! Your 3D object now looks like a professionally nished product!

FINISHING

.

33

.

AFTER SALES SUPPORT

1300 663 907 [e-mail] MODEL: HE161192

MAINTENANCE

The maintenance of 3D Printer Touch should be conducted by skilled person only. Always unplug

the printer before doing maintenance or modications.

In order to have a smoothly working 3D Printer Touch it is important to maintain it correctly. Please

follow the safety/deterioration checks during maintenance:

• Check condition of all rubber belts

• Oil the lead screens with light machine oil (sewing machine oil)

• Check the condition of the power cable. Make sure there are no cracks in the sheath

• Check the condition of the wiring on the printer to ensure nothing is pinched of damaged

• Check the fans are operational during print

• Check the chassis is secure. Tighten any screws if there is ex in the frame

DISPOSAL OF PACKAGING

This product has been packaged to protect it against transportation damage. Unpack the

appliance and keep the original packaging carton and materials in a safe place. It will help prevent

any damage if the product needs to be transported in the future, and you can use it to store the

appliance when it is not in use.

In the event, it is to be disposed of, please recycle all packaging material where possible. Wrapping

can be a suocation hazard for babies and young children, so ensure all packaging materials are

out of their reach and disposed of safely. Observe any local regulations regarding the disposal of

packaging and dispose of it appropriately for recycling. Contact your local authorities for advice on

recycling facilities in your area.

DISPOSAL OF PRODUCT

Observe any local regulations regarding the disposal of waste products. Contact your local

authorities for advice on recycling facilities in your area.

At the end of its working life, do not throw this product out with your household rubbish. Electrical

and electronic products contain substances that can have a detrimental eect on the environment

and human health if disposed of inappropriately. Observe any local regulations regarding the

disposal of electrical consumer goods and dispose of it appropriately for recycling. Contact your

local authorities for advice on recycling facilities in your area.

.

34

.

TROUBLESHOOTING

10.1 Troubleshooting

If having any troubles when using the 3D Printer Touch, please refer to the troubleshooting guide

below, or call customer support on 1300 663 907.

You can also visit cocoonproducts.com.au for support videos and advanced tutorials.

10.1.1 Printing Problems

Clicking sound from one of the stepper motors

One of your stepper motors may not be connected properly. Check each connection and then

inspect the cable routing for any faults

File not printing

Remove the SD Card and insert into your Computer. Open the GCODE le using a text editor (eg.

Notepad), and inspect if GCODE is readable or not. If le consists of multiple ‘ÿÿÿÿ’ symbol, then le

has been corrupted. Try reformatting your SD Card and reloading the GCODE le.

NOTE: Reformatting will delete all les on your SD card

Not extruding when starting to print

Ensure that the nozzle temperature has been set to match your material

Not sticking to the bed

• Ensure that the bed is clean and free from dust

• Check that the bed is level and set to a distance of approximately 0.1mm

• If there are defects / deep scratches in the printing mat, it may need to be changed. Change the

mat or use blue painters masking tape

• Add a brim or raft to your le

• Check that the bed temperature matches your material

• Ensure nozzle to bed gap is not bigger than 0.1mm. Material will solidify if gap is large.

Models Warping/Curling

• Check that the bed temperature matches your material

• Check the inll % of your GCODE. The higher the inll, the more likely to warp

• Add a brim or raft to your le

.

35

.

AFTER SALES SUPPORT

1300 663 907 [e-mail] MODEL: HE161192

Model appears very ‘stringy’

• Ensure that the lament diameter is set to match your lament spool (1.75mm), then try

creating a new GCODE before printing again

• Check you are using the correct temperature for the lament used

Print stopped halfway

• Check that the GCODE le is complete and not corrupt

• Check the original model le

The motor does not stop at the end of axis

Check that the stop micro switches are aligned with the motor mount and registering.

The print head/bed does not move

• Check the part can be moved by hand when stepper motor is disabled. Clear anything that is

blocking the path

• Check that the motor is turning (using position menu). If motor turns but belt does not, you

will need to tighten the gear motor gear nut. Please visit cocoonproducts.com.au for further

support.

10.1.2 Connectivity Problems

My 3D Printer Touch isn’t turning on

Check that you have correctly inserted the power cable into the rear of the Control Box, the power

cord is plugged into the mains outlet and that the Control Box power switch is on.

TROUBLESHOOTING

.

36

.

10.1.3 Other Problems

Filament stuck when removing

Please visit cocoonproducts.com.au/3dprinter/videos for a video on how to clear the nozzle

with stuck lament.

Where can I buy more lament?

If you require more lament, visit our online store, cocoonproducts.com.au to purchase various

colours and types.

What brand of lament should I buy?

We recommend using only Cocoon Create branded lament. Lower quality generic laments can

damage your 3D Printer Touch and potentially void your warranty.

What types of lament can my 3D Printer Touch Print?

The Cocoon Create 3D Printer Touch accepts various types of laments including PLA, ABS, PVA,

HIPS and specialty laments such as wood, exible, luminous and conductive. For our full range of

laments visit cocoonproducts.com.au

10.2 Useful Terms

ABS Filament

Commonly used plastic lament with good strength and industrial properties

Brim/Raft

Types of printed foundations that help models adhere to the printbed

Display

Provides the main interface for operating the 3D Printer Touch

Firmware

Software that is programmed into the electronic board

GCODE

Code that is produced using the slicing process. Describes the movements and temperature

TROUBLESHOOTING

.

37

.

AFTER SALES SUPPORT

1300 663 907 [e-mail] MODEL: HE161192

settings of your 3D Printer Touch

Heated Print Bed

Surface that your 3D objects are printed onto

Nozzle

Opening at the bottom of the print head where lament is pushed through

PLA Filament

Commonly used plastic lament with low environmental impact

SD Card

Secure Digital memory card. This is where your GCODE les can be stored and accessed by the 3D

Printer Touch

Slicing

Process that turns a 3D Design into a code that can be used by 3D Printer Touch

Spool

Filaments of PLA and ABS are wrapped, creating a spool

Stepper Motor

DC motors that move in discrete steps. This allows for precise positioning and/or speed control

.stl

A common le format for 3D Designs/Models

USB Cable

This cable allows communication between the Cocoon Create 3D Printer Touch and a computer,

using the USB port of the computer

TROUBLESHOOTING

.

38

.

APPENDIX

References

Some of the 3D Models used in this manual and other included materials were sourced from the

below:

Repair and Refurbished Goods

or Parts Notice

Unfortunately, from time to time, faulty products are manufactured which need to be returned
to the Supplier for repair.

Please be aware that if your product is capable of retaining user-generated data (such asles
stored on a computer hard drive, telephone numbers stored on a mobile telephone, songs
stored on a portable media player, games saved on a games console or les stored on a USB
memory stick) during the process of repair, some or all of your stored data may be lost.

We recommend you save this data elsewhere prior to sending the product for repair.

You should also be aware that rather than repairing goods, we may replace them with
refurbished goods of the same type or use refurbished parts in the repair process.

Please be assured though, refurbished parts or replacements are only used where they
meet ALDI’s stringent quality specications.

If at any time you feel your repair is being handled unsatisfactorily, you may escalate your
complaint. Please telephone us on1300 663 907 or write to us at:

Winplus Australasia

PO Box 537 Bayswater Business Centre, Victoria, Australia

1300 663 907 - Hours: Mon-Fri 8:30am - 6:00pm AEST

[e-mail]

AFTER SALES SUPPORT

1300 663 907

AUS

[e-mail]

YEAR WARRANTY

1

MODEL: HE161192 PRODUCT CODE: 56826 01/2018

3D Printer Touch

create

.

.

.

Repair and Refurbished Goods

or Parts Notice

Unfortunately, from time to time, faulty products are manufactured which need to be returned
to the Supplier for repair.

Please be aware that if your product is capable of retaining user-generated data (such asles
stored on a computer hard drive, telephone numbers stored on a mobile telephone, songs
stored on a portable media player, games saved on a games console or les stored on a USB
memory stick) during the process of repair, some or all of your stored data may be lost.

We recommend you save this data elsewhere prior to sending the product for repair.

You should also be aware that rather than repairing goods, we may replace them with
refurbished goods of the same type or use refurbished parts in the repair process.

Please be assured though, refurbished parts or replacements are only used where they
meet ALDI’s stringent quality specications.

If at any time you feel your repair is being handled unsatisfactorily, you may escalate your
complaint. Please telephone us on1300 663 907 or write to us at:

Winplus Australasia

PO Box 537 Bayswater Business Centre, Victoria, Australia

1300 663 907 - Hours: Mon-Fri 8:30am - 6:00pm AEST

[e-mail]

AFTER SALES SUPPORT

1300 663 907

AUS

[e-mail]

YEAR WARRANTY

1

MODEL: HE161192 PRODUCT CODE: 56826 01/2018

3D Printer Touch

create

.

.

.

.