Cocoon HE150277 Instruction Manual

INSTRUCTION MANUAL

Model Number: HE150277

create

Warranty Note

If you experience any issues with this product, or it’s
performance is not what you had expected, please
contact us at Winplus before returning the item to the
store.

It is likely that we can resolve any problems for you via
phone or email.

We can be reached on:

Phone: [phone] (Mon - Fri; 8:30am - 6:00pm EST)
Email: [e-mail]
Web: www.winplus.com.au

Important

Getting the most out of your 3D Pen:

Read the manual carefully

It will help you get set up with ease

Visit www.cocooncreate.com.au

We’ve got additional support videos and guides

Call After Sales Support - 1300 663 907

Available Monday - Friday, 8:30am - 5:30pm AEST

Email [e-mail]

We’re always happy to help

.

Warranty Details

The product is guaranteed to be free from defects in workmanship and parts for a period
of 12 months from the date of purchase. Defects that occur within this warranty period,
under normal use and care, will be repaired, replaced or refunded at our discretion.
The benefits conferred by this warranty are in addition to all rights and remedies in respect
of the product that the consumer has under the Competition and Consumer Act 2010 and
similar state and territory laws.

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law.
You are entitled to a replacement or refund for a major fail

ure and for compensation
for any other reasonably foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the failure
does not amount to a major failure.

AFTER SALES SUPPORT

YEAR WARRANTY

1

[e-mail]1300 663 907

AUS

3D Pen

create

MODEL: HE150277 PRODUCT CODE: 52916 02/2016

4

After Sales Support

1300 663 907

Model Number HE150277

02/2016

[e-mail]

Important Safety Instructions

Before you get started, please read these important safety instructions.

Caution: The Cocoon Create 3D Pen generates high temperatures at the nozzle that can

cause injury. Do not touch the tip of the 3D Pen nozzle while operating, and allow time for

the nozzle to cool down after operation.

Vapours/fumes may be irritating at operating temperatures. Always use the

Cocoon Create 3D Pen in an open, well ventilated area

Do not leave the Cocoon Create 3D Pen unattended during operation

Contact with extruded material may cause burns. Wait for extruded material to

cool before touching the object

Use the Cocoon Create 3D Pen on a heat-resistant at surface as the device is

hot during operation. Do not place the 3D Pen on any type of fabric or ammable

material at any time

• The 3D Pen must not be exposed to water or rain, or damage will occur

• Do not attempt to modify the internal components of the 3D Pen, or disassemble the

device under any circumstances

• Do not use the 3D Pen if damage of housing or cables are evident

• In case of emergency, turn o the 3D Pen at the power outlet

• When not in use, eject plastic lament from 3D Pen to prevent building up of residual

lament inside the 3D Pen

• Unplug the 3D Pen and adaptor and store in a cool dry place, keep out of reach of

children

5

After Sales Support

1300 663 907

Model Number HE150277

02/2016

[e-mail]

Contents

Warranty Details 3

Important Safety Instructions 4

Parts List 6

Technical Specications 6

Product Overview 7

Instructions 8

Connect to Power 8

Heating the 3D Pen 8

Trim Filament 9

Insert and Load Filament 9

Draw 9

Adjusting Extrusion Speed 9

Standby Mode 9

FAQs 10

Repair and Refurbished Goods or Parts Notice 11

6

After Sales Support

1300 663 907

Model Number HE150277

02/2016

[e-mail]

Parts List

Technical Specications

Features

1 x 3D Pen

3 x 3 Metre 1.75mm ABS Filament

1 x Power Adaptor

1 x Getting Started Guide

1 x Instruction Manual

1 x Warranty Card

Extrusion:

Extruder Diameter: 0.7mm

Filament Input Speed: Slow (Approx. 0.08cm/s) - Fast (Approx. 0.75cm/s)

Supported Print Materials: Cocoon Filament (PLA/ABS)

Temperature settings: 140ºC - 190ºC

Electrical:

Power Adaptor Input: 100V – 240V ~ 50/60Hz

3D Pen Input Rating: 12V

3A

Physical Dimensions:

3D Pen Dimensions: 184 x 31 x 46mm

Weight: 65 grams

• Adjustable speed

• Adjustable heat settings

• Ceramin nozzle for heat insulation

• Ergonomic design for comfort

7

After Sales Support

1300 663 907

Model Number HE150277

02/2016

[e-mail]

1 4

5

6 7 8 9

2 3

Product Overview

1. Forward Button

2. Eject Button

3. Power Indicator

4. Filament Port

5. Power Jack

6. Heat Indicator

7. Temperature Dial

8. Speed Slider

9. Nozzle

Fig. 1

8

After Sales Support

1300 663 907

Model Number HE150277

02/2016

[e-mail]

Instructions

Connect to Power

Connect one end of the power adaptor to the power jack located at the end of the pen,

then connect the other end to a mains power outlet and switch on. The Power Indicator

LED will turn on.

Heating the 3D Pen:

Press the Forward Button (refer g 1, page 7) to begin heating the 3D Pen. The Heat

Indicator LED will turn red when the 3D Pen begins heating. Once the 3D Pen has reached

the pre-set temperature, the Heat Indicator LED will turn green.

Temperature Settings

The heating temperature of the pen is set at a

default of 188ºC

Use a small at head screwdriver (not included)

to turn temperature dial to desired heating

temperature. Turn clockwise to decrease

and anticlockwise to increase the heating

temperature.

TIPS:

Below are some tips to determine if you will be required to change the temperature settings

on your 3D Pen to improve the quality of your drawings:

a. If bubbles are visible in the lament you have extruded, the heating temperature is

too high. Reduce the temperature by 8-15 degrees

b. If the lament is extruded slowly even when extrusion speed is set to high, or if

lament also appears to have a dull nish, the heating temperature is too low.

Increase the temperature by 5 degrees

c. If the lament is extruded too quickly, it will come out in liquid form. This means the

heating temperate is too high. Reduce the temperature by 10-18 degrees

190ºC

188ºC

169ºC

B

103

5c

158ºC

140º

C

140º

C

148º

C

9

After Sales Support

1300 663 907

Model Number HE150277

02/2016

[e-mail]

Instructions

Trim Filament

Cut the lament to your desired length and ensure the tips of both

ends are at. This ensures the lament can be fed through the

Filament Port smoothly.

WARNING: Always trim the ends of ejected laments prior to next

use. Placing a melted end into the Filament Port can cause the

material to jam inside the pen.

Insert and Load Filament:

Insert one end of the lament into the Filament Port. Press and hold the Forward Button to

begin loading until lament is extruded from the nozzle.

WARNING: Only use Cocoon Filament for the Cocoon Create 3D Pen (PLA/ABS is

recommended). Attempting to feed other materials through the lament port may cause

damage to the 3D Pen internally, and may void your warranty.

Draw:

Hold the Forward Button to extrude and draw. To stop, release the Forward Button. You

can change the speed of the lament extrusion by adjusting the Speed Slider.

Adjusting Extrusion Speed

The Cocoon Create 3D Pen has a stepless Speed Slider. This allows you to adjust the

speed the lament is extruded from the nozzle.

a. Move the Speed Slider forward towards the nozzle to decrease the speed

b. Move the Speed Slider backwards to increase the speed

NOTE: The speed of the extrusion can also be inuenced by the heating temperature
pre-set. If the temperature is too hot for the PLA/ABS, lament will extrude quickly from the
nozzle. If the temperature is not hot enough for the PLA/ABS, extrusion will be slow & dull

Standby Mode

The 3D Pen will automatically switch to standby mode if left unused for 5 minutes. If the

Heat Indicator’s green light is o, the pen is in standby mode. Press the Forward Button to

reheat the 3D Pen until the heat indicator LED light turns green.

10

After Sales Support

1300 663 907

Model Number HE150277

02/2016

[e-mail]

FAQs

Question Solution

Why isn’t the Power
Indicator light turning on?

• Check that power adaptor is plugged into the power jack
of the 3D Pen and mains outlet properly and that the power
outlet is switched on

My Pen is not heating up

• Check that the Power Indicator light is on

• Press the Forward Button to start heating. When 3D Pen is

being heated, the Heat Indicator LED will turn red

There is no lament

extruding from the nozzle

• Check the Heat Indicator light is green to ensure pen is
heated and ready for use

• Ensure there is sucient lament in the Filament Port. When
lament’s length is too short for extrusion, the sound of

extrusion changes to a higher pitch, indicating to insert more

lament.

• Check that the temperature is set hot enough to heat
the lament. You can adjust and increase the heating

temperature if necessary. Refer to pg 8 for Temperature
settings

• The lament may be jammed inside the port. Press the Eject
Button and trim o the ends of the lament and reinsert.

A lot of vapours/fumes
during extrusion

• The heating temperature is too high for the lament.

Decrease the temperature using the Temperature Dial

The lament is extruding

too fast

• The heating temperature is too high for the lament.

Decrease the temperature at the Temperature Dial

• Decrease the speed of extrusion by moving the Speed Slider
towards the nozzle

Filament is not sticking to
surface

• Ensure surface is clean and free from dust

• Angle the pen so that the lament is forced onto the surface

Can’t build in 3D - lament

doesn’t support itself

• Decrease the speed of extrusion by moving the Speed Slider
towards the nozzle

Repair and Refurbished Goods

or Parts Notice

Unfortunately, from time to time, faulty products are manufactured which need to be returned
to the Supplier for repair.

Please be aware that if your product is capable of retaining user-generated data (such as files
stored on a computer hard drive, telephone numbers stored on a mobile telephone, songs
stored on a portable media player, games saved on a games console or files stored on a USB
memory stick) during the process of repair, some or all of your stored data may be lost.

We recommend you save this data elsewhere prior to sending the product for repair.

You should also be aware that rather than repairing goods, we may replace them with
refurbished goods of the same type or use refu

rbished parts in the repair process.

Please be assured though, refurbished parts or replacements are only used where they
meet ALDI’s stringent quality specifications.

If at any time you feel your repair is being handled unsatisfactorily, you may escalate your
complaint. Please telephone us on 1300 663 907 or write to us at:

Winplus Australasia
PO BOX 537

Bayswater Business Centre
Bayswater, VIC 3153

Winplus Help Desk 1300 663 907
(Operating Hours: Mon-Fri 08:30AM to 6:00PM)

[e-mail]
www.winplus.com.au

3D Pen

AFTER SALES SUPPORT

YEAR WARRANTY

1

MODEL: HE150277 PRODUCT CODE: 52916 02/2016

[e-mail]

1300 663 907

AUS

create

Repair and Refurbished
Goods or Parts Notice